0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
Where is the radiator drain plug for a 1992 Chevy Beretta?
it is on the side almost at the bottom of the radiator..very hard to get too !!!!
How do you adjust the parking brake on a 1993 Chevy Beretta?
Under vthe back of the car between the rear wheels there is a cable. it should run from the back of each wheel to an adjustment screw. this screw is probablly rusted up really bad. by putting a wrench on the short side of the screw(driver side) and turning the nut that is on there you can adjust your brake one wway or the other. NOTE: upon adjusting my brake cable one day it snapped in half. then i went to the dealership and had it fixed.
How do you bleed the clutch on a 1994 Chevy Beretta?
it's the same as bleeding the brakes. find the bleeder screw by the slave piston housing. open it have someone step on the clutch for you. just keep an eye on the reservoir because since its so tiny the fluid will empty faster than on the brake system.
How do you install a voltage regulator in an 1989 Chevrolet Beretta GT?
The voltage regulator is in the alternator.
Why doesnt my 1990 Chevy beretta oil gauge work?
It is most likely the oil pressure sensor, located on the front of the engine block near the oil filter. There is also a slim possibility that the gauge in the instrument cluster is defective.
dude! sounds like air brake sys.(system needs to be bled get air out of sys.)As for gettin stuck , check linkage,brake booster and master cyl.
Your car smells like gas and when started makes a popping sound in the engine?
make sure all your sparks plugs are tight, sounds like a loose plug
Your 95 beretta has a leak and gas is getting into the oil tank---any reason why?
You have a serious problem here. This will cause permanent engine damage. It could be a bad fuel pressure regulator, or one or more injectors are bleeding off when you stop. Fix ASAP !
How do you replace the headlight bulb located on a Chevy?
more then likely w/ no more info then is provided there is a silver rod on top of the headlight pod you slide to the side then the whole light will come out and you can replace the bulb and reinstall.
How do you bleed the hydraulic clutch on a 1992 Chevy Beretta V6?
There is a bleeder on the drivers side. It is on the side of the block. You have to hold the bleed and twist the top part. Its just like bleeding brakes too so you will need another person to help you.
depending on how old the trans is, and how many times the fluid has been changed, you could have a real problem, over time, with a transmission, actual particles of the transmission tiny bits of metal, have become loose, and float around in the fluid, actually making the fluid thick and dense, now this particle packed fluid, if left alone, will continue to allow the trans to operate properly and maybe reduce, daily problems, but its only a matter of time, before this dirty fluid, causes transmission failure, This happened to me, with a Ford Windstar Van, auto trans, van had ninety thousand plus miles, totally unaware if fluid had ever been changed, so i changed it, completely, and put all new fluid, new filter, and the next day trans started to slip, then worse the next day, and so on and so on, It was explained to me, that if you have your trans checked by a pro, and he says its okay for you to change the fluid, then you must change the fluid, on time, everytime like clockwork, if he says dont change the fluid then you dont change it, just add fluid when you need it, removing all the fluid basically removes the broken bits of gears and parts, and when new fluid is put in, the gears that once operated correctly, dont because, the clean fluid, doesnt protect the teeth, and now the gears slip, Dont quote me on this next statement, but my R&R guy said if your trans is old, dont change anything, just add fluid , if its new, then follow your owners manual, recommended maintenance schedule I hope this helped you, In conclusion, I highly recommend a trip to AAMCO or Mr. Transmission, and have it checked right away, new trannys, installed, cost 2200.00 with no warranty,
Will an 1988 Beretta engine fit in a 1995 Beretta?
depends on which engines you are switching around as to how much you have to change over. Any engine from any beretta should bolt into any other beretta, tempest or corssica. However, you might have problems with computer, wiring harness, gauges, etc.
You should also keep engine and tranny from doner car together.
Can you fit a 3800 v-6 in a Chevy beretta with a 5 speed munchie?
It has been done, but not without a lot of time, money, and patience. Almost everyone that has completed the swap has said it was not worth it, and would have rather swapped in a 3400SFI or 3500SFI. Go to 60degreev6.com or talk to someone on bstuff.com for more info regarding Berettas and engine swaps of this kind.
Where does the power to the radiator fan in a 95 240sx come from?
A relay in the fusebox near the battery, its receives a signal from the ECU when to turn on
How to remove ignition switch on 89 berretta?
the ignition switch is commonly caled the key lock clyinder
If you have tilt steering then you need to take it to a dealership they will have a specail tool to remove the pivot pins in the steering column housing. this makes key lock cylinder replacement impossible for the home auto repair technician.
if it is not tilt steering 1) remove negative battery cable 2) remove steering wheel: probably need steering wheel puller for this. 3) remove turn signal switch assembly 4) place lock cylinder in RUN position 5) remove turn signal switch housing screws 6) remove turn signal switch housing and steering shaft assembly : as complete unit: 7) lift the switch tab with a screwdriver then GENTLY pull on the buzzer switch wires and remove the buzzer switch 8) place the lock cylinder in the accessory position 9) remove retaing screws fro lock clyinder and remove the lock cylinder. 10) reverse to install.
hope this helps wolverine
What kind of oil goes in a Chevy Beretta?
5w30 unless you leak massive amounts of oil, then I would put 10w30.
Change turn signal lights in 1992 berretta?
For the rear? Pop the trunk, look on the inside opposite the brake light there should be 4 plastic wing nuts (3 large, 1 small), unscrew the 3 large ones and take off, slide the whole housing out and from the car, you now have access to the light sockets, turn them (some have a clip to keep them in place, squeeze this while turning if they have it) remove socket from tail light assembly. replace bulb with 2057 and put it all back together. about a 5 min job. Hope that helps someone.
You just put a new alternator in your 94 Beretta Why are the lights still dimming?
you probably bought it at autozone and need to get a good one from napa
Does the 1988 Chevy Beretta GT have power windows and power locks?
i just got my 88 beretta gt 2 days ago and it is great!to answer your question,yes the 88 etta gt does have power windows and locks
Where is the alternator in a 93 beretta?
It will be located along the the drive belt. It will be the unit that has little vents on it and if you look inside the vents it will have copper wire windings in it. Usually it is toward the top of the engine or towrd the front. Hope this helps you. It usually has a larger power wire connection and a ground wire going to it.
Why would a 1994 Chevrolet Beretta lose coolant and shake at about 60 mph?
Take it to a repair shop and have them do a block test to determine if you have a blown head gasket.
Remove the headrest from a 1996 beretta?
you must remove fabric from the upper seat there is a lock clip at the bottom of the post.. for more info... http://www.topspeedautogroup.com
