0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
Low on Coolant Defective sensor? Sensor not connected when radiator installed? If none of these are true try disconnecting battery for 10 mins. to see if this resets sensor
How do you replace the front wheel hub assembly on 1995 Chevrolet beretta?
Pre-soak bolt if you can a day before with wd-40 or something simliar.
1. place car in neutral (block tires so it does not move) 2. jack car up and remove tire
3. remove brake caliper, should be a 3/8 allen bolt. Press in piston cup for brake( one step less on assembling.)
4. remove rotor
5. get a t-55 hex head socket and there will be 3 bolt holding wheeling bearing on.
depending how long it has been you may have to use a pair of vise-grips to help turn so you don't strip out head of bolt.
6. remove axle nut 30mm socket.
7. remove wheel bearing/ hub.
8. assemble back together.
How much does it cost to fix a transmission on a Chevy Beretta?
1.it will average between $1400 and $2100 dollars depending on who does the work.
2. Had my 1992, 3spd automatic (TH125) transmission fixed here in Pensacola FL at Bellview Transmission Inc for $400 plus tax in 2006. Might be a bit higher now. Call and ask for Bob...
Where is the thermostat on a 1994 Chevy Beretta 3.1 z26 and how do you replace it?
The 1994 Chevrolet Beretta thermostat is located on the front of the engine. You can follow the top radiator hose directly to the thermostat housing. The thermostat will be in the thermostat housing.
Why would a 1990 Chevy 2500 blow the ignition ECM fuse?
Not sure why blowing but if you can look in owners manual or chiltons to see what else is on the same circuit for example fuse #2 may have fuel pump and cigar lighter on the same circuit and if something metal falls into cigar lighter it will blow the fuse each time a new fuse is put in. Hope it helps. Also on my 1989 Chevy 2500 I had the same problem and I had a short in some wiring running along the driver side frame rail by the fuel filter.
Where is Blinker Relay located in Chevy Blazer year 1995?
On this model the flasher could be located in one of two places. It is either on the steering column just under the dash, or mounted on the fuse box under the dash on the drivers side.
What causes the low coolant light to stay on a 1996 Chevrolet beretta?
There is a sensor in the side of the radiator that is most likely defective.
Do you have a Picture of a fuse panel for a 90 Chevy beretta?
I can take a picture with my camera phone and send it to you in a text message if you have a camera phone. Go to a bookstore or a parts house and get a Haynes Manual.
What is and where is the wheel bearing located on a 94 beretta and how do you replace it?
The wheel bearing is located in the Hub Assembly. It provides a reduced friction environment, making the wheel turn easier.
Jack your car up then take off your tire. there should be a large nut in the center of the hub that is your wheeling bearing nut. there is also a bearing on the back side that you must remove the brake caliper to get to.
The neutral safety switch is what controls the reverse lights.
It is located on the top of the transmission almost directly below the brake master cylinder.
How do you find what the OBD-II codes for a 1996 Chevrolet beretta?
WWW.Berettastuff.Com they will answer any question you have about codes.
Where is the turn signal flasher unit located on a 1995 Chevy Corsica?
Remove the lower dash panel in the drivers side it will be in the right of the steering coluum. == ==
Where is the torque converter lock out switch on a Beretta '92 3 1 engine?
This is the plug and not the switch....The switch inself is located within the transmission.
>
If the car has a 3spd automatic (TH125) Look on the front (closest to the radiator) driver side of the tranny for a 4 prong plug...this is the TCC plug....
Unplug it and drive the car. If the problem goes away, then you can replace the solenoid or drive it with it unplugged...it WON'T HURT THE TRANNY!! You will suffer on mileage though.
How do you replace the heater core on a 1998 Chevy Beretta?
Not sure this can be answered as they quit making Berettas in 1996. You ask about a '98.
Recently replaced the heater core in my 1991 Beretta GT. Took all day, two people to replace a $20.00 part. They steering column had to lay to the floor. The complete dash pad/panel had to be removed. Once that was done the rest was basic and easy.
changed a heater core in 93 baretta,was told to drop steering and so forth,honestly after looking,its under the center of the dash and was the easiest and fastest i have ever changed a heater core me and a friend changed it replaced it,went and got the new one in under 3 hours
Where is the brake master cylinder in a 1977 VW bug?
Under the car. Look at your brake pedal. There's a silver rod on a clevis coming out the back side of the brake pedal. It goes into a rubber boot that's sticking through the firewall. On the other side of the firewall is the master cylinder. The bolts you've got to remove to get the master cylinder out are above and to the right, and below and to the left, of the rubber boot. Oh yeah...because of where it is, there's a special way to bench bleed (prime) a VW master cylinder. The way to bench bleed most master cylinders is to clamp them into a vise, put fluid in the reservoir that's attached to them and pump the rod until fluid comes out the brake line ports. On a VW that doesn't work because you are almost guaranteed to dump the bench bleed out while you're attempting to get it under the car. It's better to install the master cylinder, hook up the reservoir hoses and the brake pedal, then fill the reservoir and put someone in the car to pump the brakes while you keep the reservoir topped up. Put a metal--very important--container under the master cylinder. When you hear fluid hitting the metal pan, you're done.
Why my 1989 beretta gt headlights dont work?
Check the bulbs & fuses first. Then if o/k start looking for electrical problems such as switch, wiring & sockets
How to fix the cigarette lighter in a Chevy Beretta?
If the fuse is good, take the lighter out and check it in another car to see if it is good. If it is, then replace the recepticle. If it is bad, replace the lighter.
What kind of trans axle fluid goes in an 89 Beretta?
In a '89 Chevy Beretta the trans axle fluid is more of an oil and can be purshase at a local dealer. Its a 60 wt. synthetic oil. The fill tube is located between the motor and firewall,just under steering column at trans axle housing towards bottom of motor. It requires a funnle with a long flexable tube.
Edit by Loosenut: If its a stick use Styncromesh 89/90 if its automatic use Dextron III
How do you check trouble codes on a 1994 Chevy Beretta?
The ALDL port is located on the driver's side, under the dash. You will need a GM Tech1 (or compatible) scantool to retrieve codes from either a 1994 or 1995 Beretta. This is because GM was in a transitional period between 1993-1996 to comply with the government mandated OBD-II system. The diagnostic components in those years are a combination of OBD-I and OBD-II parts, and cannot be scanned with a standard scantool.
Unfortunately, unless you know someone with such a scantool (GM Tech1, Actron CP9150, etc.), you will need to go to a GM dealer to have your codes read.
Where is the o2 sensor located on a 96 beretta 3.1 v6?
There are two oxygen sensors on a 1996 Beretta.
One is down in the back of the engine on the exhaust manifold it has three wires running out of it. You will need a special tool to take it off. Edit by Loosenut: A 7/8 O2 socket. The other is on the exhaust downpipe, just before the catalytic converter.
How do you replace the fuel filter on a 1996 Chevy Beretta?
the fuel filter on a 96 beretta is on the driver side in the rear underneath. it is about as big as the oil filter and is silver. it is easy to take off. The fuel filter in my 96 Beretta is on the passenger side in the rear of the car right above the axle. It's also big and cylindrical. Someone suggested that you first start the car and shut it off in gear. That way, there won't be as much pressure in the gas line and leak all over the place. Suggestion: be prepared for gasoline to leak out of the lines. Do in well ventilated place or outside.
Check for a vacuum leak either under the dash or under the hood
Check the operation of the vacuum operated motors under the dash
Check the operation of the selector switch
How do you change the oil in a 95 beretta?
The oil on a 95 Beretta is changed by placing a drain pan under the engine, removing the oil filter, taking out the drain plug, and allowing the contents of the engine to drain. The drain plug is put back in, a new filter screwed on, and the oil refilled.
