0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Where is the egr valve located on a 1998 dodge neon?
driver side of the motor towards the firewall. It is a UFO shaped object with 3 hoses coming out of it and an electrical connector.
first up i would check to make sure all plug wires are installed to the correct plugs 2 wires swapped to out of sequence plugs will cause this misfire
Where is the map sensor on a 2006 dodge ram 1500?
Looking at the front of the engine, the MAP Sensor on a 2006 Doge Ram 1500 is located is just to the right of the EFI or Electronic Fuel Ignition (what used to be the carburetor). There are two sensors located here plugged into the EFI. The MAP Sensor is the second one in from the front.
Can a torque converter out of a 350 Chevy work on a 396 Chevy big block?
YES
As long as the flexplate is the same size or has additional mounting holes.
To add to this answer in depth. i changed from a 350 to a 454. the 454 had a th400 transmission and the 350 had a th350 transmission. (This was a 4x4 so we had to use the th350 transmission because it had a married transfer case)the th400 flywheel did NOT match the th350 torque converter. We installed the th400 converter and it fit perfect in the th350 transmission. I would make sure torque converter bolts to flywheel and as well fits into trasmission before attempting to install in vehicle. It is a huge pain to make the swap half way through the install.
How do you fix a front wheel bearing on a 1997 Nissan Sentra or how much would it cost in a shop?
Wheel bearings on the Sentra must be pressed in. The bearings should run around $50 each at the auto parts store, you need two. You will also need 2 different oil seals on each wheel ($10 each). I am unsure what local shops will charge for the labor but I paid $50 for seals and bearings in both wheels. If you have access to a press, you could tackle the job. Ideally bearings/races are always pressed on, sometimes not an option in the real world. 1. If the bearing fell apart you will have one race stuck on the axle and the outer race stuck in the spindle. 2. To remove the race off of the axle heat the race with a heatgun or torch, trying not to heat the axle as much, then try and pry it off (chisel-screwdriver/hammer) without damaging the axle surface. 3. On the race that is stuck in the spindle: Pry out the 2 lipseals. On the outside of the spindle next to the race remove the skinny snapring. Heat up the spindle with a heatgun/torch, punch the race out towards the outside with chisel-screwdriver/hammer being careful not to damage the surface of the spindle. 4.Throw parts away, install new ones packed with grease. 5. new ones go in easier if you heat the spindle. 6. People come here for answers, they go to mapquest for directions to an autoshop.
Where is the exact location for the oil pressure sending unit on a 1997 Dodge grand caravan es?
According to a post in http://www.dodgeforum.com, the sending unit is probably close to the oil filter, on the side of the engine. The vehicle mentioned in the article, was a 1998 dodge caravan with 3.0 v-6. Probably the 3.3 and 3.8 v-6's are in nearly the same location in relation to the oil filter, as well as the 4-cyl engines.
Where is the air temperature sensor for 2001 Dodge Dakota 47?
Service manual says the IAT(intake air temp) sensor is installed into the intake manifold plenum near the left side of throttle body. it appears to screw in and out.
Hemi is short for hemispherical. It refers to the heads on an engine that are basicaly domed in shape. It is supposed to provide more compression area allowing more fuel mixture to be ignited at a time thus increasing horsepower. I'm fairly certain I'm remembering the definition correctly.
How do you align the drive plate with the crankshaft on a Dodge 318 engine in a Ram 1500?
The crankshaft and driveplate have an "offset" bolt pattern. If you look at both youll see the bolt pattern is misaligned intentionally so as the driveplate can only go on there one way.
What should the oil pressure be for 97 dodge ram 2500 5.9 liter?
Minimum of about 10 psi at idle, 30 psi at 3000 rpm
Where is the location for a 1983 dodge ram pick -up truck's freeze plug?
There are three on the left and three on the right sides, and two on the rear.
Can A Dodge Ram 1500 Have Police Lights?
Depends on the owner. If they are a volunteer fire fighter or undercover police then yes. If it's your buddy, then no, they can't.
Oil pressure sending unit location for 1995 ford ranger 2.3L?
According to Auto Zone, it is on the driver's side, in the upper part of the ENGINE BLOCK, above the level of the upper transmission case.
It is on the drivers side of the block, just below the head, approx 6 inches from the rear of the engine.
Where is the location of the thermostat on a 1997 dodge ram 1500 318 engine?
Where the upper radiator hose connects to the engine, you will find the thermostat under the housing.
How do you remove the rear tail light assembly on a 2004 Dodgea Ram 1500?
open you tailgate and there should be 2 screws with hex heads take those out and it should pop straight out
Does a 1999 dodge durango 518 auto trans have a modulator valve?
No. That transmission has a computer controlled electronic governor. If it is not shifting properly you need to start by checking PCM codes.
