answersLogoWhite

0

🚗

Dodge Ram

The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.

13,744 Questions

Location of fuel filter on 2000 dodge stratus es?

it's back at the gas tank. kinda hard to get to!!! I think top front! Fuel pump too if I'm not mistaken. I have the same car. If you can afford it, change both!!!!

What does it mean when you get code P0442 on a elandra 2000?

Trouble code P0442 means:Evaporative emission control system leak detected (Small leak)

How much horsepower does dual exhaust add to dodge ram 1500?

Not a significant difference all the dual exhaust does is cut back pressure ergo the louder sound

How do you remove overhead console in 2006 Dodge Ram 1500 Quad cab truck?

remove the two light lens be careful not to break them. then remove the two torx screws behind the lens. give a slight pull down on the front of the console to remove the two clips and you are done.

98 Dodge Ram 1500 - My Power Mirrors and Dome light have stopped working and no longer have power. I do not see them listed in the interior or exterior fuse panels anywhere. Where is the fuse located?

I'm answering my own question since no one else seems to be able to do it. After some investigation on my own, I found there is a fuse that is protected by a black locking tab. It is located within the fuse box on the drivers side door jamb. It's labeled "IOD" 10A. IOD stands for "Ignition Off Draw" and it is specifically there for items that directly tie to the battery to operate when your vehicle is not running, and also when the key is out of the ignition. The IOD fuse protects and supplies 12VDC to the Dome & Map lights, Power Mirrors, Cargo lights, Head lights, Parking lights, and other misc. accessories that operate while the vehicle is off.

Which rear wheel drive gearboxes can be used with j18a engine?

Vitara g16a auto. manual box bolts up but flywheel bolt pattern is different Samurai g13b box bolts up but flywheel bolt pattern is different

How do you replace a bulb for the left rear turn signal on a 98 Dodge Ram 1500?

two screws on the side of the bed where the tailgate closes over have to be taken out. then you pull the whole light assembly out there are two pins in the light to hold it in they sould pull right out they will hold the light back at first and make it hard to pull but pull strait out so you dont break the pins.

How do you adjust idle on a 1995 dodge ram diesel?

adjust it with the throttle linkage find your throttle on drivers side next to injection pump and its just 10 mm bolt to loosen and lengthen/shorten to what you need

2007 dodge ram engine light on?

could be a sencor or needs new gas cap,, mine keeps comming on and going off,, gonna try changing cap,, and if doesent work have to takeand get codes read, and if needed fixed,,

What can you do to increase your HP in your 1999 dodge Ram 1500 5.9 L V8?

Get a better air filter system with a chip and programmer and if that's not enough u can get an exhaust system or those cyclone things u put in ur air intake boot another thing would be a turbo charger

How do you remove a motor from a dodge ram 250 van 1989 model from front or out the dog house?

Front, Remove hood, grill, bumper, etc. You could through the dog house if you are superman. Leaning over the seat and picking up an engine is quite difficult.

How do you replace a starter on a 1994 Chevy pick-up?

Hey George===First remove the negative battery cable. Rme ve the flywheel cover. Then remove the bolts holding the starter to the block. Drop the starter down enough to remove the wires. then remove the starter. GoodluckJoe

What do you do if the passenger side window on a 1995 Jeep Cherokee does not work?

check your window lock switch on the drivers door control panel. That is the case with my 1990 works when it wants to.

99 Taurus how do you replace left front brake sensor?

The brake sensor is built into the wheel bearing. The whole unit has to be replaced. It is best to replace both bearings. Left wheel and right wheel ---- 1998 models have the sensors as a separate component - See "Related Questions" below for more