0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
How many speakers does dodge magnum have?
according to the JL Audio website. A dodge magnum standard SXT or SE setup has six speakers total. on the dash it has two 3.5" speakers; 6.5" speakers on the two front doors; and two 6x9" speakers in the rear.
(Hose, water pump, thermostat gasket, timing cover gasket?) It was actually the top hose that connects the water pump to the engine. There was a big rip in it and the hose was swollen from being saturated with coolant there was "muddy" mess everywhere and there is no way to see this hose as it is covered by the AC unit amongst other parts and after taking off the fan shroud and water pump, I was able to feel the short 5 inch angled hose with a finger to notice the hole. The butterfly clamps were a nightmare to remove (took over an hour) and the hose was stuck on there good. I had to twist and rip it off and use a screwdriver to scrape the remainder off. Absolute pain. I wonder if there is better butterfly clamp tools? I used needlenose pliers which kept slipping. It took little time to put it all back together with a new hose and a fresh gasket and seal. I used slothead tightening ring clamps for easier access if it ever has to be removed again.
How do you remove the door panel for a 2004 dodge ram?
You have to remove all of the Phillips screws,the door handle and the master power window switches.
Then tug up on the door panel and it will life right off.
Where is the thermostat located on a 5.2 2001 dodge ram?
It is under the housing that the upper radiator hose hooks to.
What is the head bolt torque pattern and torque foot pounds for a 2001 1500 ram 5.9 liter engine?
The torque is 95 lb/ft. The pattern is to slowly tighten in a criss cross pattern.
SMALL CHRYSLER273, 318, 340, 360 A Engine
Fastener Type Torque Spec
Main cap bolts 85 ft.-lbs.
Connecting rod bolts (plain) 45 ft.-lbs.
Cylinder head bolts, 273-318 85 ft.-lbs.*
Cylinder head bolts, 340-360 95 ft.-lbs.*
Rocker shaft bracket bolts 17 ft.-lbs.
Intake manifold bolts 35 ft.-lbs.
Oil pump cover bolt 95 in.-lbs.
Oil pump attaching bolt 35 ft.-lbs.
Oil pan bolts 15 ft.-lbs.
Cam locking bolt 35 ft.-lbs.
Cam thrust plate bolts 210 in.-lbs.
Harmonic damper bolt 135 ft.-lbs.
Flywheel/flexplate bolts 55 ft.-lbs.
Flywheel housing to engine block bolts 50 ft.-lbs.
Flexplate to torque converter bolts 270 in.-lbs.
Clutch housing bolts 30 ft.-lbs.
Front cover bolts 30 ft.-lbs.
Water pump bolts 30 ft.-lbs.
* Follow factory torque sequence
My personal experience would be replace and properly gap spark plugs, and use a higher octane gas or these yellow bottles called "HEAT". Good luck!
How do you repair an oil leak on a 1994 Chevrolet Cavalier 6-cylinder intake manifold?
The lower intake on either the 2.8L V6 the 3.1L V6 or the 3.4L V6 all are the same set up lower intake gaskets are very common to leak oil at the lower intake gasket due the the fact that right below it is the push rods and lifters. if you want to get your hands dirty and attempt to do it yourself there's some work to this job and requires a good memory and cautious removal and installing habits. LET'S BEGIN: First take off the air cleaner hose then the PCV hose then unhook all throttle body cables and connector wires also the 2 coolant hoses below the throttle body as well as the upper radiator hose, then unhook the vaccum hose from the back of the upper intake manifold then remove the 3 bolts/nuts on the bracket that's in front of where the vaccum hose is that you just removed. Remove the EGR valve just take out the 3 bolts don't try messing with the steel line it'll be rusty and hard to remove without damaging. The gasket should be ok to reuse on the EGR valve as long as it doesn't get torn in the process or so replace it. Next remove the upper intake manifold the gaskets although they are paper they can be reused if not damaged. But normally its best to replace them. Next unhook the fuel rail make sure to do this so safely with the key off and the battery unhooked or the fuel pump fuse unhooked. take off both fuel lines. Next remove the wires from the injectors be careful you have to push in the on clips do not pry on them they will break. If they are hard to push in I recommend using needle nose pliers to make it easier. Next remove all bolts from fuel rail. Then evenly pull up on the fuel rail if not done cautiously injectors can be broken. A pry bar will help removal when used carefully. The O rings on the injectors if not damaged can be reused if not damaged but make sure to lube them with a light coat of grease before installation otherwise damage and possible leaks could happen. Next remove the drive belt then remove the alternator and the unhook the wires. Next remove the Power Steering Pump bolts there are 3 of them and they are behind the Power Steering Pump pulley they are 10MM bolts rotated the pulley to access each bolt for removal. There is no need to remove the Power Steering Pump hoses simply lift up the Power Steering pump and place out of the way. next remove the valve cover bolts these are torx head bolts remove all 4 on each valve cover take off the valve covers the gaskets if in good shape on the valve covers can be reused if not replace them its worth the money if you've gotten into it this far. Next remove the lower intake manifold bolts then pull up on the lower intake manifold make sure all hoses are unhooked and out of the way as well as wires. Remove old gasket and cautiously clean the gasket surface lay a rag or cloth or towel in the valley to prevent gasket material or dirt etc. from getting into the oil. Next install new lower intake gasket. Use Black RTV Silicone on the ends of the gasket to hold gasket in place. Then reassemble in reverse make sure to properly tighten all bolts and fasteners to prevent stripping or leaks due to improper torque. I am only doing this for instructional purposes and this should only be looked at like guidelines since there are differences between years and engine setups, if you are unsure of or have problems with anything after following these instructions I suggest that you take it to a mechanic.
I am not responsible for anyone's problems or issues.
Your heater is not blowing air you can feel heat but will not blow?
The heater in all cars use a fan motor to blow the hot air. If you do not feel blowing air the fan is broken and needs to be replaced OR the fuse to the fan motor is burned out and needs to be replaced OR the fan switch that turns on the fan motor is bad OR the wires running to all of these is not connected somewhere. The solution? Check for a fuse in the fusebox that says "Blower" or "Fan". Remove it and put a new one in. If this does not work bring it to someone to test the other things, you cannot do it yourself.
Why on 1995 Camry starts but it turns off soonest you let go the gas pedal?
you will most likely need to change the spark plugs
Where is the fuse box under the hood of a 1992 Plymouth voyager?
The fuse box is not located under the hood, its located right under the steering wheel, there is a panel that just pops off to access the fuses.
What happens if you take the catalytic converter off of a 1998 Chevrolet Silverado?
It would be plain stupid to remove the converter. The converter is designed into the engine controls of the vehicle. Removing it wouldn't really increase power because they have very little backpressure. If you want to remove it because its plugged or bad then you could do so but the check engine light would come on and it would never pass a smog test. It won't physically hurt the engine to remove it. Removing the converter is against the law. I would have an aftermarket converter welded in to replace your old one if its bad.
What is the size of a 2004 Dodge Ram gas tank?
1500 Short Box 98 L (26 gal.)* 2500/3500 Short Box 128L (34 gal.)* All Long Box 132 L (35 gal.)*
If this is a Chrysler product would think the speed sensor went bad.
How do you remove and replace cabin air filter on 2001 dodge ram quad cab?
It wasn't built with a cabin filter.
How much horse power does chip add on dodge ram 5.9l?
The "chip" or programmer should have that listed on the package.
Where is the camshaft position sensor on a dodge 5.9 liter 1997?
That would be the pick up plate in the distributor under the rotor and cap.
What is the horse-power of the Dodge Cummins?
The Dodge Cummins has a rating of 160 horsepower for the years of 1989-1993.
Where is the ac orifice tube on a 99 DODGE ram 1500?
It is made into the high pressure line about midway where it runs along the passenger side fender. If replacing, you must replace the whole line.
Where is the transmission solenoid in a 1500 dodge ram 2003 5.9?
It is inside the transmission, on the valve body.
On a 2000 5.9L 4x4 Ram 1500 how do you remove the air filter?
There should be a hose clamp around the base of the air filter housing on the throttle body. You can access the screw for this clamp from the drivers side using a flathead screwdriver. Loosen this clamp, then unsnap the intake and the return hose from the passenger side of the engine. Lift up on the filter housing and there is a rubber washer that "snaps" down on a "bolt in front of the housing. Once you have the entire housing loose and out of the engine compartment, unsnap the 3 latches on the front and then it should be easy sailing from there. NOTE: when you reinstall the housing; 1. make sure the rubber gasket is installed on the top of the throttle body; 2. make sure you get the hose clamp reattached properly. Unfortunately, this generation of dodge ram air filters is a pain to put back together. Hope this helps!
Where are the O2 sensors located on a 2002 Tundra 4.7 Limited RWD?
You should have 4. Each located on the exhaust near the catalytic converter. The upper (before the catalytic converter) are about a foot away from the catalytic converter towards the engine. The rear (lower) are the same distance toward the rear of the vehicle. The drivers side upper O2 sensor is the most difficult (due to wrench access) to change but all are fairly easy.
How do you remove radio from 1997 Dodge Ram?
Remove the decorative radio retaining plate. Remove the radio retaining screws. Remove the wiring harness, from the back of the radio.
