0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Gather necessary tools and materials.
If you plan to change your oil regularly, consider investing in the Following.
1. Small Floor Jack.
2. Jack Stands.
3. A Socket Set with adapter to go from 3/8 to 1/2 inch for strap wrench.
4. A Strap Wrench.
5. Oil Drain Pan.
6. A Funnel.
7. A Magnetic retrieval tool (to retrieve the plug encase you drop it in the hot oil).
8. Leather Gloves or Rubber Gloves (like the doctor's use, available at most auto parts).
Run the car's engine for 10 minutes before you drain the oil. Warm oil drains faster than cold oil.
Park the car on a level surface, engage the parking brake and turn off the engine.
If your car has a low clearance, raise it by driving it onto a ramp or by jacking it up and supporting it securely.
Open the hood and place the new oil and funnel on top of the engine to ensure that you won't forget to add oil afterwards (an expensive mistake that many D-I-Yer's make!). Tips:
Wear gloves to remove the plug if it's hot.
It's always best to replace the oil drain plug gasket.
Use the right size wrench or socket. Don't use an adjustable wrench: you can strip the drain plug bolt.
Consult your owner's manual or an automotive parts specialist to find out the weight of oil and type of oil filter your car needs.
You'll need the year, make, model and mileage of your car if you go to an auto parts store.
You will also need to decide what oil and filter you are going to use, Synthetic or Conventional.
Warnings:
Make sure the car is securely supported before you crawl underneath.
You will need two jack stands to support the front of your car after jacking it up.
Never get under a car that is supported only by a jack! A pair of jack stands costs less than $20.
Handle hot automotive oil with extreme care.
Only dispose of used motor oil and filters at authorized locations.
Used oil contains many carcinogens, avoid contact, and wear leather or rubber gloves. Draining the Oil and Changing the Oil Filter Steps:
1. Crawl under the car once it is securely supported.
2. Locate the oil drain plug on the underside of the engine, usually near the front center of the car. Consult your owner's manual for the exact location.
3. Place the oil drain pan under the plug and loosen the plug with a socket wrench. Remember: turn counterclockwise to remove bolts.
4. Remove the plug by hand. Be prepared for the rush of hot oil!
5. Let the oil drain into the pan. Hold onto the plug. (if you can)
6. Reposition the pan, if necessary, to catch all the dripping oil.
7. Wipe off the drain plug and the plug opening when the oil finishes draining.
8. Replace the drain plug gasket.
9. Reinstall the plug. Always start threading any bolts or screws by hand to prevent cross threading.
10. Tighten with a wrench or socket. Be careful not to over tighten the plug.
11. Locate the existing oil filter. Oil filters are usually on the side of the engine.
12. Position the oil pan underneath the filter to catch any remaining oil.
13. Use strap wrench to loosen the old oil filter if it is too tight to remove by hand. Make sure the rubber seal of the old filter is not stuck to the engine.
(Be careful when removing the old oil filter. It's full of oil.)
14. Use a rag to wipe the area where the filter mounts to the engine.
15. Use some new oil to lightly coat the rubber seal of the new filter.
(If you are lucky and your filter is straight up & down pre-fill the filter with fresh oil till it remains full.
Doing this will help with the startup lack of oil going to the engine.
Even if the filter mounts sideways you can pre-fill it to the point where the fresh oil is soaked into the filter material.
16. Screw the new filter into place by hand. Tighten 3/4 turn after the filter makes contact with the mounting surface, no more, no less!
It's usually not necessary to tighten the oil filter with the oil filter wrench, but have it at the ready if you're grip's not strong (or large) enough. Installing New Oil and Cleaning Up Steps:
1. Locate the oil filler cap on top of the engine. Remove it.
2. Place the funnel in the opening and pour in the new oil. Typically, you will use 4 to 5 quarts of oil. Check your manual for the correct oil capacity.
3. Replace the cap when you're finished.
4. Run the engine for a minute or two.
5. Check the area around the oil drain plug and the filter for oil leaks. Tighten the plug or oil filter if you find leakage.
6. Use rags and newspapers to wipe away excess oil.
7. Pour the used oil into a plastic container after the used oil cools. (Old 1 gal milk containers with screw-on lids work great for this.)
8. Dispose of the used oil properly: either bring it to a recycling center or an auto repair shop that can recycle it for you. Don't pour it down the sewer!
REMEMBER
Record the date and mileage after you change the oil so you will know when your car is due for another oil change.
It helps to put a small sticker on your windshield to remind you or a small service book available at your local auto parts store, that you keep in the glove compartment or console. Hope This Helps.
The transmission is 1997 dodge 1500,2500,3500 with the 5.9L. Just 1 year fits but you can use 1/2, 3/4 or 1 ton trucks. Must have a 5.9L. The transfer case must be out of a 1/2 ton truck otherwise its different. You can use 97 or 96 if it has ID# 52098357
What is the timing on a dodge 318?
Depends on the year and application, could be anywhere from 0 to 12 degrees.
Please ask a new question with more info.
I have an 04 same engine etc having the same identical problem. Have you found a resolve yet?
Where is the PCV valve on a 2006 Dodge Ram 1500 5.7L?
On the passenger side and behind the throttle body there is a wing nut looking part. It is under that.
Where is the Leak on the front passenger side coming from?
If it tastes and smells sweet, you have a leaking heater core. If it is just water, you have a leak at the windshield or the A/C condenser drain line is clogged.
What is the best tool to use to remove the CV axle nut?
Honestly, a 1/2 in. impact wrench, with the impact socket that fits the nut. Could be a 28mm,30mm,32mm... or so. Use a torque wrench to install the new nut--over tightening can lead to bearing damage. Don't forget to punch the notch in on the nut to lock it in place. Use a new nut if possible. There's only about 90 lb-ft of torque on one of these nuts, so a socket on an 18" breaker bar works fine.
The fuel pressure is WAAAY too high 35 psi is about what it should be at. New fuel pump is needed. That should be your solution.
How do you take the front rotors off on a 2002 Dodge Ram 1500 2wd?
With tire removed you will need to unbolt the caliper which is held on by two bolts caliper bolts). Once the bolts are removed you should be able to dislodge the caliper by grasping the top and pulling back or by rocking from top and bottom. Secure the caliper with a hanger to the frame not the rubber lines, be careful the pads may come loose. You will now have to remove the the caliper bracket also attached by two bolts. Once the bracket is removed the rotors should slide right off the studs. If corrosion has built up lightly tap around rotor with rubber mallet or a piece of wood and hammer. GOOD LUCK!
Hi, Have you found out what the problem was? If so could you please let me know what it was because I am having the same problem. Thanks
What oil does a Dodge Ram 1500 5.7L use?
5w20 or 5w30, depends on if it has MDS.
If the oil cap says 5w20, use 5w20.
What is the numbering and placement of cylinders in a Dodge 3.7 L engine?
V6
pass side 2-4-6
driver 1-3-5
Old 225 cu inch inline 6
1-2-3-4-5-6
Normal running temp for your cummins diesel engine for your generator?
The normal operating temperature for a Cummins diesel engine in a generator typically ranges between 180°F to 220°F (82°C to 104°C). Maintaining this temperature range is crucial for optimal performance and longevity of the engine. If the temperature exceeds 220°F, it may indicate potential overheating issues that need to be addressed. Regular monitoring and proper maintenance can help ensure the engine stays within this optimal temperature range.
What is the correct idle RPM for a Dodge 318?
The proper idle speed for a Dodge with a 318 cubic inch engine about 475 to 500 RPMs. Any idle below that will cause stalling.
How do you change the transmission governor solenoid and sensor for a 2000 dodge ram 1500 46RE?
drain pan while pulling pan, pull pan off, then on drivers side of trans you will see where the valve body bolts to the far right side of truck, there is a sheetmetal retainer that holds both the solenoid and the sensor in place, pull the 3 1/4" bolts that hold it to the trans along with the 2 torx srews, once all bolts and screws are removed pull downward on sheetmetal retainer/bracket and the solenoid should pull right out of valve body, once solenoid and bracket are removed you can pull the black sensor out of the side of the govenor block. reverse to install!
Where is the vertical headlight adjustment screw on a 2002 cavalier?
The headlight adjustment screws are found in 2 holes behind each headlight, through the air shield. They are gold star shaped bolts.
Perhaps a bad master cylinder--return plugged or restricted As friction develops at rotors brake fluid expands and pushes back into master cylinder if return is restricted, expanded fluid will cause caliper piston to put pressure on rotor, essentially applying the brakes
NOTE: I had same problem with front left and it was the Caliper, had to rebuild the caliper
Will a trailer with a 7 prong trailer plug that works with a GMC also work with a 2003 Dodge Ram?
Yes, a typical 7 RV plug will work with any other 7 RV plug regardless of year make or model of tow vehicle.
Where would you get a dip stick for a dodge ram 2500 diesel?
You can get a cheap universal generic dipstick from the "Help" product line at your local auto parts store just ask the counter-man. Also at your local Chrysler Dealership Parts Desk will have the direct replacement part or should be able to order it.
How do you fix motor with malfunctioning electronic throttle system?
That depends on what the malfunction is. Start with checking for trouble codes.
That depends on what the malfunction is. Start with checking for trouble codes.
What is the front track of the 2012 RAM 1500?
The front track of the 2012 RAM 1500 is 5 ft. 8 in. (68 in.).
What is a 0441 Check Engine Light code in a 97 Dodge Ram?
P0441 EVAP Emission Control System Purge Flow Fault You can try cleaning the gas cap of any debris and reinstalling till you hear it click. Or it could be a bad purge solenoid. Or cracked or split lines in between in the evap system.
