0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Where is the shift solenoid on a 2005 dodge ram 4x4?
Inside the transmission, on top of the valve body.
What is the horsepower rating on a 1965 Pontiac Tempest 326 engine?
250hp The Horse Power rating stock is 250 HP
Where is the vacuum canister on a 1998 Pontiac Transport?
If you mean the Emissions Evaporator canister; it is under the vehicle fastened to the frame near the fuel tank. It is a rectangular shaped black plastic box with a few hoses and lines connected to it. The lines are connected with quick connectors, and there are some going to the fuel tank and some going up front to the engine.
1999 dodge ram 1500 standard cab 318 magnum the ac works great but the heater is not woking at all?
Low on coolant.
Stuck open thermostat.
Plugged heater core.
Faulty temp blend door.
Where is the thermostat located on a 2002 dodge ram 1500 5.9 ltr?
At the end of the upper radiator hose where it connects with the top of the motor.
What is the proper headlight adjustment height for a 2006 dodge 1500?
http://www.coolbulbs.com/HID-VISUAL-HEADLIGHT-AIMING-PROCEDURE.pdf
What are the symptoms of a faulty throttle position sensor 92 f150 4x4 EFI 351?
some sympons of a fault tps is tht it bogs out when throtel is opened quickly alot of the time it will only rev up to a sertant pint like it has a rev limeter on it other times it may be very slugish at the begining then all of a sudded it just gets the power back after the throtel is opened about 30% to 50% i hope this helps you out
"addtional info" to see if the problem is the tps disconnect the sensor. If you have the same idle your sensor has gone or is going bad.
How much HP is a stock 6.7 Cummings 2010 Ram?
350 horsepower and 650 ft/lbs of torque is the standard rating for highway use variants of the 6.7 Cummins (not Cummings) ISB engine.
Need to remove cooling fan on 07 dodge ram 3500 cummins?
I don't know why you would need to remove the engine fan, but here is some information on how to do so. The nut that mounts the fan and clutch to the hub is a 36MM though a 1 7/17" Wrench will be close. Instead of purchasing a fan removal wrench you might rent one from a local auto parts store. 2007 Cummins spins counter clockwise so your nut will be right hand thread. Lefty loosey, righty tighty. You will need a large pair of channel locks to grab the hub bolt heads, or a large tool like a screw driver to pry them still so the fan assembly does not rotate while you work to loosen the fan nut, which will likely be very tight.
Many wheels and pulleys are very tight on the shaft and must be removed using a "puller". There are several types, some use jaws or clamps, others use bolts. The ones that use bolts come in different configurations with one of the configurations being "three bolt".
What that means is that the puller is attached to the pulley or wheel using three bolts, then a center bolt is used to push the puller and wheel/pulley assembly off the shaft. Many wheels and pulleys are very tight on the shaft and must be removed using a "puller". There are several types, some use jaws or clamps, others use bolts. The ones that use bolts come in different configurations with one of the configurations being "three bolt".
What that means is that the puller is attached to the pulley or wheel using three bolts, then a center bolt is used to push the puller and wheel/pulley assembly off the shaft.
Can you bypass the oxygen sensor on a 1995 Dodge Ram Truck and if so how?
Yes. I just unplugged the 02 sensor and car runs fine , not dumping excess fuel , I also removed the front and rear plug-ins at the throttle body , will know more about the mpg after the tank has been used . I'm trying to get my van ready for an HHO system and I was told by them that the fuel economy will be between 20 and 40 percent because the 02 sensor will make the mixture run "rich" when the hydrogen is burned , ATM the 02 sensor is unplugged and only the check engine light is on , if this does not make the computer "run continuously lean" My next step will be to isolate the return voltage wire from the 02 sensor in the harness and run a hot lead from the battery and then regulating that voltage with a resistor to around 3.5v . Will update as events permit
Can you adjust the automatic choke for a 5.2 L 1994 Dodge Ram pick up?
A 1994 Dodge Ram is fuel injected and does not have a choke.
Why is my 2004 Dodge Ram 2500 with a Hemi blowing white smoke there's no mixture of oil and water?
Check the coolant level. Is there a sweet smell to the white smoke from the exhaust? Sounds like either a blown head gasket or a cracked head.
How do you reset a airbag light on a 99 dodge ram 1500?
The light can not be reset without fixing the cause of the code that turned the light on.
How do you set the ignition timing on a 1994 dodge ram 360?
The distributor is synched to zero degrees with a scan tool. It can not be done with a timing light.
What power adders can you put on a 04 dodge 1500 hemi?
I added: Hypertech chip, K&N air filter, headers with dual exhaust. The best improvement came from the headers.
