0
Jeep Grand Cherokee Laredo
The Jeep Grand Cherokee Limited is an upgraded version of the Grand Cherokee, with leather interiors, alloy wheels, heated seats and mirrors, and remote keyless entry. It’s powered by either a 5.6-liter or a 4.0-liter V8 engine.
3,451 Questions
Why would your 92 acura integra be leaking on your passenger side floor board?
There is a good chance that the heater core has rusted out. This is a little radiator inside the passenger compartment for transferring heat from the engine coolant to the air in the cabin. Always fun to replace.
In 2002 they had the I6 motor still, it takes 6 qts. with the filter change.
A thermostat stuck in the closed position is very common in overheating problems. Simple to check: Remove the radiator cap and start the engine. Look through he filler neck to see if you see the coolant circulate when the engine reaches normal operating temperature. If you don't see water circulate, more than likely the thermostat is stuck.
Is the pinion nut on a 1993 jeep grand Cherokee Laredo right threaded or left threaded?
Right hand. Righty tighty lefty loosey.
What is oil capacity for 2004 jeep grand Cherokee 4.0?
The 4.0L and 4.7L require 6 quarts of oil. This includes filter capacity. If you've lost your owner's manual for your Cherokee, you can download the original at Jeep's website, free of charge. The address is http://www.jeep.com/en/owners/manuals/index.html
Where is a flasher fuse located on a 1997 Jeep Grand Cherokee Laredo?
The '99 flasher fuse is in the fuse box in the engine compartment and the flasher switch solinoid in under the dash on the left side. Hope this helps.
The flasher fuse is located on the kick plate of the passenger side above the fuse box. I actually just replaced one too!
There is a little black stopper there, known as a ramp in the parts catalog. It stops the wiper arm and blade from going to low and getting stuck on the lip. The part number is 55155124 and goes for about $17.5, depending on the dealership. However, it is not unheard of somebody placing a larger size wiper blade if they are out of stock and unaware of the consequences.
What is the fuel pressure suppose to be on a 1997 Jeep Grand Cherokee with a 4.0?
39 psi plus or minus 5
39 psi plus or minus 5
What was serviced and by who? There is no way anyone can tell you what is wrong and how much to fix. The fact is that something is wrong with the SRS and you must get it fixed. The air bag could deploy at any time or not at all. Take it to your dealer.
Answersounds like your service tech may have been probing wires and probed an airbag wire a definite factory fixJeep Cherokee tps sensor location?
In most cases the TPS (throttle positon sensor) is located at one end of the throttle plate shaft. The throttle cable/linkage is attached on one side of the throttle plate shaft and the tps is attached to the other side.
Where is the cooling fan relay located on a 2000 Jeep Grand Cherokee with a 6 Cylinder engine?
Either take off the bumper or cut a 3" hole underneath the right headlight and you'll be able to access it
Where can a driver door be purchased for a 1994 grand Cherokee jeep limited?
dealer or junk yard. ahhh, is this a "real question"?
How do you take the door panel off to put window on track?
lower window to down position(if you can) remove door panel remove window weather stripping remove black window surround (should be a screw on top of surround towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window reveverse putting in
Where is the neutral safety switch located for the 1994 Jeep Cherokee?
On the passengers side of the trans about even with the front of the door fan shaped switch held on by two bolts.
I suggest taking it apart and cleaning it before you think about replacing.
The switch is nearly $300
To remove, flatten out the retaining washer side under nut, remove large nut, remove smaller ( 14mm ) bolt on the adjustment side.
cleaning is easy, 6 screws in back, pull apart, clean out all that old grease, pay special attention to the two contacts on the sweeper arm, they should move in and out easily as they have springs underneath and are the man contacts, apply new di-electric grease and reassemble.
reassemble and align before tightening, easiest way is to put trans selector in R and move switch until reverse lights come on.
What is the Correct tire size for jeep grand Cherokee year 2000?
The label in the drivers door jamb will have that information.
How do you change a brake light bulb on a 2003 jeep grand Cherokee Laredo?
Can a 1998 Jeep Grand Cherokee last long?
If you take care of it and don't drive the H#$% out of it it can last 300,000 miles without breaking a sweat.
How to change a water pump on a jeep 4.7 Cherokee?
WATER PUMP 4.7L ENGINES
The water pump on 4.7L engines is bolted directly to the engine timing chain case/cover.
A gasket is used as a seal between the water pump and timing chain case/cover.
If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.
The water pump can be removed without discharging the air conditioning system (if equipped)
REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.
The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive 4.7L Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.
CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.
If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - 4.7L When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.
Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - 4.7L Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - 4.7L Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing 4.7L for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.
Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks
How do you replace the right turn blinker on a 1997 Cavalier?
hi i can help you to replace the right blinker light, first raise the hood second there is a splash guard that runs the lenght of the fornt end just right above your headlights , remove that panel next you have two 1/2 inch bolt to remove ,then pull out the head light assy, next look to the blinker light and turn the socket 1/2 turn and pull out , replace then just put everything back toghter ,, hope this helps it did on my 99 ..
How do you check to see if your radiator fan is working on a 1999 jeep grand Cherokee?
Turn on the A/C and then turn the ignition to the on position without starting the engine. The fan will be running if it is good.
