0
Oldsmobile Cutlass
The Oldsmobile Cutlass was a compact/mid-size car produced by General Motors from 1961 to 1999. The Cutlass was one of the most popular nameplates in the vehicle industry during the 1970s.
1,158 Questions
1993 Cutlass Ciera starts won't drive when put in gear no reverse either?
how bout this on the 79 there is a vacum line to the trannie connects to trannie if comes off car wont go into gear look under for lose hoses. hope this helps
How do you change the oil pump on a 91 olds cutlass cierra 3300 v6 and where is it located?
The oil pump is located on the bottom of the engine. Drain the oil from the oil pan. Remove the oil pan. Remove the oil pump retaining bolts. Reverse the process to install your new oil pump.
I'd call a locksmith. They will be able to tell you the exact problem and how to fix it.
Where is the flasher component box on a 1994 Olds Cutlass Supreme?
In order to locate and replace the cylindrical shape flasher module, the four screws holding the fusebox in must be removed. The glove compartment door hinge is sort of in the way so it is best to remove glove compartment screws, though glove compartment door will still stay on. the cylindrical shape flasher module is located behind fusebox and it has to be searched for by feeling for it. In my case I found it by reaching behind fusebox to the left. I was told to first turn on my four way directional signal so that after I disconnected the cylindrical shape flasher module I knew for sure that I was not disconnecting the four way cylindrical shape module. Now the cylindrical shape flasher module that I removed was yellow in color and the one I bought to replace the cylindrical shape flasher module was silver in color. Getting the fuse box out took a little tilting and angeling to get out
What is the push rod placement for a 1998 oldsmobil 3.1?
With the engine in the car...from left to right....Front head is L-S-S-L-S-L Rear head will be L-S-L-S-S-L
How do you know when your fuel injectors are bad?
To Diagnose:
Throttle body injection:Take a light and as the car runs look at the spray pattern from the injector, it should be cone shaped and the same all the way around, any breaks or streams rather than an even spray means the injector is faulty. Port injection:Figure out what cylinder has the problem, I usually inspect the spark plugs first, then do an ignition short test. The spark plugs may have one or more showing a distinct difference in the colour of the deposits.Insure the computer and wiring are firing the injector, I have a set of noid lights for this, available from most automotive tool suppliers.
Insure there are no vacuum leaks, spraying WD40 or similar around works really well.
Remove and if possible bench test (at this point if I think I have a bad one I spend the average $35.00 (average) and replace the bloody thing.)
Your 1986 cutlass timing keep changing you have to keep setting the timing back?
Your timing chain may be worn to the point it is jumping a tooth and thus changing the timing. If you can hear the chain that is a good sign it is worn. I would inspect the timing chain.
What weight oil do you use for a 1994 Oldsmobile cutlass ciera?
you would use 5W-30W have the same car
1994 Oldsmobile Cutlass Ciera S 3.1 where is egr solenoid 3?
the Egr valve is located on the top of the engine on the left side near the intake ducting it has a bundle of three solenoids that stand vertically about one and a half or two inches they are black plastic one of them is number three if a trouble code says that a misread on number three you can remove the cover with a torx bit and try and remove the exhaust carbon build up be careful the solenoids themselves are spring loaded and can shoot out when the cover is removed reaassemble after cleaning and it may take care of the problem
This could be ecm (electronic control module) problem.
How much horsepower does a 1987 442 Oldsmobile cutlass have?
they stock 307 engine code "9" had 170 hp for 1987
Where is the VIN on a 1970 cutlass?
The VIN is located in several areas on a 1970 Oldsmobile Cutlass.
The Body VIN is on the driver's side dash and is viewable by looking through the windshield from the outside.
The Frame VIN is located on the outer side of the frame on the Driver's side about 1 foot up from the rear arch. It may be too rusty or covered in undercoating to see without some careful cleaning first.
The engine VIN is stamped on the block on a tab that protrudes from the cylinder wall that is closest to the driver's side front of the car.
The transmission VIN is also stamped onto the housing.
All of these VINs will have the same last 6 digits if the car is truly numbers matching.
Dan
Collector Car Corral
http://www.carcorral.com
How do you change the heater core on a 1989 Oldsmobile Cutlass Ciera?
How do you change the heater core on a 1989 Oldsmobile Cutlass Ciera? or where can I get the Info on replaceing it
Where can I get a free Ac diagram for 96 Oldsmobile ciera?
Try at http://www.autozone.com and sign up, they may have one..........
How do you adjust the idle on a 1993 Oldsmobile Cutlass Supreme?
In most 1990s and later vehicles you cannot adjust the idle. It is controlled by the ECM or computer. An idle that is not correct indicates something like a vaccuume leak or a sensor issue.
Where is the brake light switch located on a 1993 Nissan Sentra?
The brake light switch is located above the brake pedal on a 1993 Nissan Sentra. To reach the switch the driver's door needs to be opened.
I'd suspect a vacuum leak or a problem with the EGR valve, but if I were working on it I wouldn't replace anything until I've had a chance to check into it further. Clean the air intake mass air flow sensor with carb cleaner. . How can you crank it "in gear"??? You got sensor problems.
Why wont your car start after your upper radiator hose burst I fixed hose still wont start?
You may have overheated the engine or seized it.
How is the drivers headlight reached and replaced in a 94 Cutlass Ciera S not sealed beam?
you got to take the headlight assembly out To take the assembly out, first remove the corner marker light by removing three T-5 Torx screws. This will allow access to two of the (4) 10mm hex head cap screws, remove them. The other two can be removed by entering through the 2nd slot in the grille. Onjce those two are out you may have to loosen the grille slightly to get the headlight housing ridge out from behind the grille. Once out, remove the wire holder and terminal clip. The geay angle piece and then be rotated clocwise about 10 degrees and should pop right out. (note some dumb sob designed it to rotate clockwise to remove it)
What is the firing order for a 1994 Oldsmobile Cutlass Supreme 3.1L V6?
All 3.1 engines have the same firing order - It is 1,2,3,4,5,6
How do you take off the governor on an Oldsmobile?
If the "oldsmobile" was made in the last 20 years, it is computer controlled.
How do you replace a wiper motor for a 1999 Olds Cutlass?
Remove the wiper arm from your 1999 Oldsmobile Cutlass wiper motor. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
How do you fix your speedometer on your 1990 Oldsmobile cutlass?
May have to take it to a certified speedometer repair shop
