0
Plymouth Voyager
The Plymouth Voyager is a nameplate used in two different vans produced by Chrysler Corporation (later DaimlerChrysler AG) from 1974 to 2000. The name was also used in Plymouth’s minivan in 1984.
1,288 Questions
Where is the CCD module located in a 1998 Plymouth voyager?
There is no CCD module. CCD is the acronym for the communication system between computers on a 1998 Voyager. The engine, transmission, abs, airbag, cluster, HVAC, body, etc all communicate over the CCD bus, which is a pair of twisted wires.
How do you adjust the headlights on a 1996 Plymouth Voyager?
There are adjusting screws at the top and sides of the lights.
The screw posts are threaded bolts with a 4mm hex shape end on it and can be adjusted with a socket wrench.
The vertical screw post adjusts the light up (counter clockwise) and down (clockwise) and is located in an access hole on the top of the light assembly just to the outside of the headlight center.
The horizontal (left/right) adjustment screw post is located on the back of the light assembly towards the car center. Turn the post clockwise to lower the headlight beam and counter clockwise to raise it.
Why does serpentine belt jump off when wet 1999 ply voyger?
Serpentine belt has stretched and needs replacing or the tensioner is defective or both.
If it were me I would take the air bag back out and make sure the wires arn't "pinched" or broken and make sure that it has a good tight connection with the clockspring connector. If that doesnt solve it then the airbag control unit has failed for somereason. Hope this helps some.
How do you remove the lower ball joint on a 1991 Plymouth grand voyager without taking it to a shop?
go buy a ball joint sperader at any major parts dealer
I am pretty sure that it is computer controlled. There is probably an input to the computer that is out of whack. There may be a code stored it the computer that may elude to the problem. If an input like a mass air flow sensor or crankshaft sensor is going bad, it will report false data to the ECM and it will make an incorrect adjustment that will flood or starve the fuel/air mixture causing a stall.
easier, try to clean or maybe change the IDLE AIR CONTROL VALVE, located near the throttle body, where the air intake is, it's not difficult, it's attached with 2 bolts, then it's like a pintle with one spring, check the spring shape and replace the unit with a new one, this valve controls the air flow to your engine and if it goes bad , the RPMS are likely to be low and also stalling could occur right away when you start the engine or suddenly too
How do you change the front left cv axle on a 1997 Plymouth voyger 3.3 liter?
remove wheel and caliper. remove axle nut undo tie rod end remove horizontal bolt at the bottom of spring and strut assembly that attaches it to lower control arm pry down on lower control arm and the spring assembly will swing out and away from axle axle should now pull out of tranny
How do you install a power steering pulley on a 2002 voyager?
First you'll need to remove the pump. You will need to do this from underneath, so make you have the truck safely supported high enough to work comfortably underneath.
With the pump out, you will need to remove the pulley. Use a power steering pulley puller and very specifically not a jaw-type puller to remove the old pulley. At best, the jaw pullwer might remove and destroy the old pulley, but more likely it will just break pieces of it off making a big mess and such. That's not what you want.
To press the new pulley on, you can use a special toolkit made just for this purpose. I expect you haven't got one so we'll go with plan B which is actually much simpler. The special toolkit is complicated and not much fun.
Bring the pump to your local hardware store or home improvement store or auto parts store. Find a bolt that screws nicely into the shaft of the pump. Write down the size of this bolt including thread size.
Next, purchase a HARDENED STEEL BOLT that size and a nut to fit and three washers and some grease.
Apply some oil to the shaft. Using just your hands, put the pulley onto the end of the shaft as straight as you can. You won't be able to push it on, but you can get it stuck there pretty straight. Do this.
Next, coat the threads of the bolt with the grease and the washers also. Screw the nut all the way onto the bolt. Put the three greasy washers onto the bolt next. Then, with these items in place screw the bolt into the shaft. While holding the bolt with one wrench, use another wrench to screw the nut so that it pushes the pulley onto the shaft just a bit.
Next, unscrew the nut a few turns and tighten the bolt into the shaft a bit more., then use the nut to push the pulley on as far as you can. Remove the nut, then the bolt. Flip the washers over, then screw the bolt back into the shaft. Again use the nut to push the pulley on as far as possible.
Loosen the nut again and remove the bolt again.
Verify that the pulley sits flush against the shaft. If it doesn't correct this.
If at any time the bolt breaks off, this means it wasn't a well hardened bolt. Remove it and get a good bolt.
Can you use 16 inch rims on a 15 inch rim?
Not sure what you're asking here.
You can't put 16 inch tires on 15 inch wheels (or vice versa), hence the different sizes.
You can, however, put 16 inch wheels on a vehicle that normally has 15 inch wheels. You just need to ensure that the bolt pattern and center holes are exactly the same measurements and you may need to use a lower profile tire to achieve the proper tire-to-wheelwell clearances.
Where is the speedometer sensor in a 1991 Plymouth voyager and how do i replace it?
It is in the axle shaft housing on the right side of the transmission. It is held in with one 10mm headed bolt.
Hood latch cable Plymouth voyager brokehow can i open hood 1994 mini van?
Go through the gril with a pair of needle nose pliers and a flat head screw driver, pry over the lever and get the needle nose pliers to pull on the cable
12 volt ign/acc = red 12 volt battery/memory = yellow ground = Black power antenna = blue amp turn on = blue/white stripe amp ground = black/white stripe illumination = orange dimmer+ = orange/white stripe dimmer- = orange/black stripe phone mute = brown right front+ = grey right front- = grey/black stripe left front+ = white left front- = white/black stripe right rear+ = violet right rear- = violet/black stripe left rear+ = green left rear- = green/black stripe
How fix Fuel injector leak Plymouth Voyager?
replace the rubber o rings u may have to replace the injector if its leaking fuel through it
What would cause a 2002 Cougar to stutter on acceleration at low rpms?
Could be a multitude of different things, I am trying to fix that same problem. Could be bad a throttle position sensor, a leaking or detached vacuum hose or a dirty fuel filter is what I've heard.
How many hours labor replace heater core 1999 Plymouth voyager?
About 2, you can remove by sliding towards the gas pedal.
Why does your 97 Plymouth gran voyager gas level alarm go off with half a tank of gas?
Well, this is a fairly common problem in the late 90's model Plymouth, Chrysler etc. vans. The fixes have usually been a new fuel pump or a new seal on the fuel pump. It isn't getting enough pressure to tell the guage that you still have enough fuel. Therefore, I would have this checked soon as the van may begin to stall on you, if it hasn't already. If money is an issue(like it is for all of us)just keep the van above half full until you can get it in for repairs.
Where is the body control module on a 1997 Plymouth Voyager?
It is on the back side of the under dash fuse box.
What would cause wiper blades to collide on a 2000 Plymouth voyager van?
Bent or misinstalled wiper arms.
Why would a car jerk after coming to a complete stop?
It COULD be a motor mount or worn suspension component.
What type of transmission fluid does a 1997 Plymouth voyager hold?
the manual say's for three speed transmission to use atf 3 for four speed trans use atf 4 when I replaced the fluid in my trans the dealer gave me atf 4 I told him It calls for atf 3 he informed me that Chrysler has replaced the atf 3 with atf 4 and it won't hurt it yet every book and posts i have been to tell you how important it is to use the right fluid any way to answer the question use atf+4
Is a 1992 Dodge Caravan transmission interchangeable with a 1991 Plymouth voyager?
As long as the engines are the same size, yes. Different engine sizes have different bell housings, but 1992 to 1995 use the same transmissions (dodge caravan, Plymouth voyager, Chrysler T&C) as long as the engine size is the same.
Be 110% sure to use ATF+4 transmission fluid or you will be replacing the trannysoon anyway.
Suprisingly, changing the existing transmission fluid twice (or flushing the tranny) using ATF+4 fixes about 70% of the problems I've had with the A604 transmission these minivans use.
Dexron with an additive does NOT qualify. You can get ATF+4 at WalMart for under 4 bucks a quart, a change takes ~4.5 quarts. Changing it twice dilutes (to about 25%) whatever crap was in there already.
Remove a rear door lock from a 97 Plymouth grand voyager?
Begin by removing the inside door panel on your 1997 Plymouth Grand Voyager. Remove the door lock linkage. Remove the door lock retaining bolts. The door lock will come out.
