0
Toyota Cressida
The Cressida was a mid-size luxury car manufactured by Toyota Motor Corporation in December 1976-February 1993. Throughout its production history, the Cressida used different engine types such as L-series (diesel), R-series (gasoline), G-series and M-series.
480 Questions
Where can I find a rear axel for a 1989 Toyota Cressida passenger side?
Check directly below the trunk. It should have two wheels/tires attached. No charge, you're welcome.
How to remove a door panel on a Toyota Corolla?
Find the gaps around the door and pull, there are snap screws around the door. They pull out easily, if you have trouble use a screw driver. The hard part is the c clamp on the handle, that's if you have a manual window. They sell a tool specifically for it at auto zone, or someplace like that for under five dollars.
How do you keep the brake lights from staying on all the time on a 93 corolla?
There is a push off switch under the dash that when the break pedal is depressed is activated. Look for it and replace it. Most of the time it is not the switch what is broken but a rubber part on the pedal level that is responsible for pushing the switch to the off position.
What direction does the crankshaft pulley bolt turn to loosen on a 1983 Toyota tercel?
On my 1990 Tercel it turns counter-clockwise. It's in there tight, but mine came out. Spray some penetrating oil on it first and let it soak. You don't want to break it off when it comes out. Especially if it's been in there for awhile.
How do you remove the center console from a 2001 Toyota Corolla?
2 remove the cdplayer/tape unit...pull out the center air vent underneath the CD player. There will be 2 x 10mm bolts in there...remove boths and bobs your uncle
Where is the oil filter located on a Toyota Cressida?
The oil filter is located on the front of the motor under the exhaust manifold
How do you reset the alarm on a corolla 1993?
To reset the alarm on a Corolla 1993, place they key in the ignition and turn it until it clicks. Keep the key in this position for 10 minutes and then start the car as normal.
What are the torque specifications for 1991 Toyota Cressida cylinder head bolts?
Whatever you do, do not use the Toyota-recommended Factory Specs, unless you want a repeat of the blown gasket in a couple of years. Toyota failed its loyal customers by not owning up to this intrinsic problem with its FlagShip vehicle. Check around The Web - You will find that the REAL Torque is a few ticks more than Toyota recommends - A Torque Spec designed to fail. To answer your question 70-74 ft.lbs. is adequate don't use the 58 ft.lbs recommended by toyota. The 58ft.lbs was based on an asbestos head gasket, which was outlawed before the 7mge went into production. Hope this helps.
Check engine light 1991 Toyota Cressida?
If the check engine light is on for your 1991 Toyota Cressida, that makes that some repairs need to be made to the engine. Taking the car to a certified mechanic to perform a diagnostic test can confirm if there is any issues with the engine.
Sounds like air in the brake lines or power steering fluid in the brake system instead of brake fluid.
How do you change out the timing belt on a 2001 Toyota Corolla?
If the engine type is 3ZZ there isn't a timing belt. This engine is VVT, so the valves are moving by a chain that lasts much more than belt.
Is there an emergency fuel door release on a 2005 Jetta?
There is not an emergency release on that vehicle. You'll have to pull the carpet back to pull on the cable that goes from the solenoid to the release.
How do you replace the rear view mirror on a 2002 Jaguar XK8?
Special adhesive needed available at auto parts or Wal-Mart
How do you install the belt on a 2001 Toyota Corolla?
I assume you mean the serpentine belt that drives the various accessories (i.e., water/power steering pumps etc.) and not the timing chain (which some may mistakenly call a belt). If so:
1) Working from back to front, loop the belt over the power steering pump, tensioner and crankshaft pulleys first followed by the a/c compressor and water pump pulleys. This leaves the alternator pulley (the easiest one to access) to be the last one to have the belt installed.
2) Place a socket (19 mm hex) and extension bar/ratchet on the belt tensioner arm's hex shaped projection and rotate it clockwise (looking at the pulley end of the engine)as far as it will go. This will loosen the belt sufficiently so that the last bit can be placed on the alternator.
3) Gently release the tensioner arm so that the belt is tensioned.
4) Inspect the belt to ensure that it correctly positioned on each pulley.
5) If available, use a tension guage (e.g., Burroughs Tool BT 3373-F or similar from Kent-Moore, Snap-On tools etc.) to verify that the tensioner is working properly. Unfortunately, the only place to position this tool is that portion of the belt between the crankshaft and a/c compressor pulleys which means removing the right hand engine under cover and getting underneath the car.
6) Run car, check for unusual noises/proper operation.
How do you replace the alternator on a 1989 Toyota Corolla?
Remove the Negative terminal. loosen all belts as well as the tensioner bracket first then unplug the connector (+), then remove the remaining 4 bolts.
Try disconnecting the negative terminal while the engine is on, if the car dies it is your alternator.
1990 Toyota Cressida spark plug sequence on engine?
how the sequence of spark plugs goes on the engine of 1990 Toyota cressida
start by checking choke operation but it sounds like MAP( Manifold Absolute Pressure ) sensor is going bad be sure to disconnect battery before starting project the reconnecting after everything is mounted and hooked back up to prevent shorting out electrical sensor
How do you you replace a headlight on a 2003 Toyota Corolla?
To replace the entire headlamp assy you must remove the bumper cover. There are fasteners across the top, inside fender skirt and along the bottom and also a few clips inside the grill that are accessible from underneath. Three bolts fasten headlamp assy to the radiator support and there are three quick electrical connections.
Where do you check transmission fluid level?
you look for a dipstick at the bottom left of the engine
How do you change front brakes on a 1990 Toyota Corolla?
I have never changed breaks on my own before and I just did them on my 90 corola by myself.. It only took me 30 min to get them both done. Just pull the wheels of then the rotors and tear into it. Pretty simple just look at it before hand so you know how to put it back together. One thing you should do is pop the break fluit cap for compressing the pucks. other than that it really is simple.
