0
Toyota Cressida
The Cressida was a mid-size luxury car manufactured by Toyota Motor Corporation in December 1976-February 1993. Throughout its production history, the Cressida used different engine types such as L-series (diesel), R-series (gasoline), G-series and M-series.
480 Questions
starting with the redesigned 1998 altima the engine crankshaft was balanced much better to reduce vibration. we have a 1993 and a 1999 altima with the same engine and the 1999 is so smooth at idle i sometimes can't tell if it's running.
Where can you find the location of knock sensor in a 1992 Toyota Cressida?
If you have the 7MGE engine: Then the knock sensor is screwed into the engine block, directly underneath the intake manifold.
How do you replace an instrument light in a 2001 Toyota Corolla?
You need to take any plastic switches or buttons out of the way and then using a screwdriver, take every screw out that is holding the dashboard in place..be sure to remember where everything goes so when you put it back you won't forget anything. Once you take the instrument display off (screws hold into the bezel) there are little light bulbs that simply pull out..locate the burned out bulb and replace it...
- Note
Check all fuses before you take anything apart because it also could be a burned out fuse
Does this process work as well with a 1997 Corolla?
I found 4 screws on my 1997 (2 in the top of the instrument console) and 2 near the bottom of the center instrument panel, but that didn't seem to get me anywhere.
I still couldn't remove the panel and replace the bulb.
How do you replace the alternator on a 1995 Toyota Corolla automatic?
disconnect neg.battery cable. disconnect wires from alternator. loosen pivot and lock bolts. detatch drive belt. remove pivot and lock bolts from the bracket. installation is reverse of these steps.
Where is the location of the fuel filter on a 1989 Toyota Cressida?
the fuel filter is located under the intake manifold, if your last name is Houdini you can get to it, otherwise you will need to take the intake OFF...Good Luck and God Speed
Kryptonitefusion (3/11/07): The fuel filter is located under the intake manifold but u will not need to remove the intake! its very easy, u'll need an long extension and that's should do it. this page should help as well http://www.thermactor.com/files/pages/Howto/ffilter.htm
How do you remove the front and rear speakers on a 1992 Toyota Corolla?
I am in the process of the same thing. What I have found out so far is. Remove the three plastic screw type plugs from the rear board, then remove the third break lite, next remove the two seat covers on each side of the fold down seats, (have not figured that out yet), next unbolt the two seat belts from the side, next there are several black clamps inside the trunk that hold in the rear carpeted panel that you will need to pry sightly loose for the panel to slide out and over the speakers. Now tell me how to remove the two side cousions? KJS3964@juno.com
Try to use Toyota speaker adapter plugs so you don't need to cut wires and mess the electric system up. You can get them from Ebay or Amazon.
Hi, I just finished replacing both front and back speakers in my 92 Corolla. This answer is right up to removing the rear brake light. The side cushions are held on by a piece of metal and are easily removed by lifting the cushion up and then towards you. You also do not need to remove the seat belts as long as you don't mind putting a little more muscle into taking the rear board out. I just bent the edges enough to get it past, there was no damaging the board involved. As far as the wiring goes, the speakers I took out used adapter plugs, but the ones I put in were from a Hyundai Accent (exact same speakers, different plug) and I just cut the wires a soldered the wires together. As long as you do it right (hook up the positive to the positive and the negative to the negative...very easy to tell, the negatives all have a black line on them!) it's impossible to mess the electrical system up by cutting the wires!
As far as the front goes, on the driver's side there are four screws you need to take out to get the panel off (panel under the steering wheel). On the top of the panel there are two screws for the panel you need to take off and two more that are for the upper panel, you'll understand when you take a look. The front speakers are inside plastic mounts, so you have to take the mount off with the three screws holding it, and then take the speaker out of the plastic mount. Again, the front speakers are hooked up with plugs, but soldering is as good a connection as you can make, just be sure to tape over the exposed wire to prevent shorting out or any other problems. On the passenger side you have to open the glove box to get to all the screws and I believe there are a total of 5 screws on that side. But from there it is the same as the driver's side. The front is easier than the back but it's way harder to find replacement speakers for the front because they're smaller and uncommon.
How do you replace headliner on Mitsubishi eclipse 1996?
1. Remove the interior weatherstrips around the doors. These just pull straight down.
2. Remove the sunvisors and disconnect the power cord for the lights.
3. Remove the interior light -- this just pulls straight out with no screws.
4. Remove the rear seat bottom -- pull the little rings at the front bottom of the seat and lift the front of the seat up and out.
5. Remove the panels to the sides of the rear seat that cover the rear speakers.
6. Remove the rear headliner trim -- this is a plastic panel between the headliner and the hatch lid. Pull this straight back toward the rear of the car and be careful -- you will likely break the inside plastic anyway and this part isn't available anywhere. You might have to reattach this with screws or something after you're done.
7. Look for little plastic plugs on tabs at the edge of the headliner. Use a tool to remove these (a door panel puller with a forked end works great on this, but you could probably use a screwdriver).
8. Remove the headliner through the hatch opening.
How to reset alarm for 94 corolla after changing battery?
To reset an alarm for a 94 Corolla after changing the battery, place the key in the ignition and turn it slightly. Let it remain in that position for several minutes before starting the car.
Fuse box for 1991 Toyota cressida?
The Fuse Box in the Toyota Cressida in located on the driver side kick panel near Gas peddle.
It stands for Health And Safety At Work (as in The health and safety at work act)
Where is the Belt release lever in 1991 Toyota Cressida?
There are two belt release levers, each located on opposite sides of the emergency brake handle in the center console.
How do you change the carrier bearings on a 1985 Toyota Cressida?
to change carrier bearings in rear differenial you have to remove the rear differential from the vehicle. then remove the cover. remove the bearing caps. remove differential carrier unit. remove bearings. install new bearings. and then reassemble.
recommend having a professional repair shop peform repairs
How do you replace a spring loaded MB rear view mirror?
To replace a spring loaded MB rear view mirror first press in the spring and remove the old mirror. Next, get one end of the spring-clip on the new mirror in place and hit with a rubber mallet to snap the other end in place.
Where_is_the_tail_light_fuse_location_in_a_toyota_cressida_86_i_need_digram_or_schamatic_blue_print
How do you change the brake pads and rotors on a 2000 Toyota Corolla?
You simply remove the wheels. Unbolt the calipers from the bracket and use some wire to hang it from the strut. In order to get the rotors off to either replace or get machined you either need a rubber mallet or a piece of wood and a hammer. You will probably have to smack the rotor pretty good a couple of times as you go around it to break it free from the rust bond it has probably made. Put the rotor back on, slide the pads out of the caliper and put new ones in according to the instructions on the brake pad box. Re-attach the caliper and put your wheel back on. That's it.
Since some brake pads don't come with instructions: after you remove the old pads, you will need to compress the cylinder with a C-Clamp or some other clamping mechanism. Then you can install the new pads. Also check to make sure the new pads have an indicator tab, if they don't, remove the tab from the old pads and attach it to the new pads.
After you are done, make sure that after you start the car for the first time, you press the brake pad all the way to the floor and let it out slowly. It will press easily to floor. Do this a couple times until you feel normal pressure on the brake pedal. This process pushes the cylinder back out so that there is pressure on the brake pads when you press the brake pedal. NOT DOING THIS IS CAN BE VERY DANGEROUS!
The 1987 Toyota Corolla came in two door and four door models, a multitude of colors and a 4 speed manual transmission and a 4 cylinder engine.
How do you remove oil pan from 1986 Toyota Cressida?
there are about 12 10mm bolts that hold the oil pan in place. remove them and the pan will drop right down.
How do you turn off the Maintenance Required light on a 2005 Corolla CE?
Toyota has two different ways to shut of the light. the first way is set your milage display to the actual mileage. turn the key off. push the odometer trip button and hold it while turning the key on several dashes will display when all the dashes disappear its reset. the other way is for newer Toyota vechicles they require the vehicle to be set to trip a..but that didnt start til 07' i think..your owners manual also tells you how to reset it.
What is code P0441 on a 1998 Toyota Corolla VE and how do you repair it?
Trouble code P0441 means: Evaporative Emission System Incorrect Purge Flow
Where is the ignition coils on a 1995 Toyota Corolla?
Instead of the ignition coils I wonder if you want the Igniter. Or as Oreily's calls it the Spark Control MOdule. If so, look on the battery support, or on the drivers side of the fire wall. Approx 3 inches square with a pig tail coming off it. The coil is I belive in the distributer.
Toyota Cressida Motor head gasket problem?
Welcome to The Wonderful World of being a Cressida Owner - Toyota built or designed that engine with incorrect torque for the head gasket, so it blows, and needs at minimum a lower engine rebuild, but when you do, make sure you increase the head head bolt torque to the NEW and Recommended spec, to prevent a recurrence in a couple of years. 'Tis a shame Toyota never owned up to this serious intrinsic fault and stepped up to the plate and offered an 'Out-of-Warranty' fix for its loyal customers.
Where is fuse box 1989 Toyota Cressida?
ther is a fuse box in the engine bat but there is also a fuse box behind the kick panel on the drivers side u need to take off the skuff plates to acsess this that take off the kick panel be sure to do it gently as Toyota rnt well known for there plastic clips its beside the exelarator
Your 89 Toyota Cressida cranks but does not start what do you do?
Look for spark and fuel 1st then comeback
How to replace brake lights in 1999 Toyota corolla?
From the AutomotiveForums link mentioned below:
Remove the plastic corner panel that's inside the trunk covering the back of the light assembly and reach in with your fingers and remove the bulb and socket. From the back it's easy to confuse whether you are removing the brake light, the backup light or the blinker light socket so it would help to have an assistant step on the brakes or turn on the parking lights etc. to make sure you've got the right bulb. Installation is the reverse of removal . . .
Where is the fuse panel located on a 1989 Toyota Cressida?
Open the glovebox and look inside to the right. If I remember correctly, that is where it is. lower drivers side of dash, engine compartment, and passengers kick panel.
