Vauxhall Vectra

hi , try www.crazyleds.co.uk, Ive got mine dash on 03 vectra done nicely ;-) chers

There are several posts already in this forum which may help you.If this is not the case,you should post again with more details,particularly the X*** number for your engine and the year.CDI is really an equipment level indicator.The operation varies,depending on age and whether 8V or 16V,I can't tell from the info provided.Sorry.

If it's a diesel (which Cdi suggests it is), it's quite likely it is cam-chain, and hence will not need to be changed on a regular/scheduled basis.

To fit a Vectra diesel 2.0 fan belt, make sure that you make reference to the user manual.

under the handbrake

It's a cambelt.

start be removing the wing mirror adjuster panel. just pull on it. then take off the handle. ther are 4 screws. than take off the door card. to more screws at the bottom. remove the plastic sheet from inside. you can see the mechanism. if the window was smashed then the old rail can just be slid out by hand. clean out any glass from the wether seal round the out side. if the window was smashed ther will be lodes of glass lefed in ther. move the mechanism down to about half way. (like the window was half open) there is a torque screw in a slot. it adjusted the movement of the window. take it all the way out so the mechanism is free to rock round. slide the new window in to the window slit. then the new window on to the front runner. then get the back one on. get a friend to help. its a very fiddle job. once both runners are on and the window is in the seal at both ends then push the back end down in to the seal. the arm with the bolt shod line up with the slot agen. put the bolt back in and titen. move window up and down to check operation. put the door card back on.

this was on my t reg vectra when the windo was smashed by a theaf

Add a switch in to turn off the traction control using the method described on this tutorial: http://homepage.ntlworld.com/mallwood/traction_control.htm

Andy.

The idle air control valve on a Vauxhall Vectra B is located on the intake manifold. The valve is placed in front of the air tubing, right behind the engine cylinder head.

Will a tow bar of a vectra b fit a vectra c

yes

IS IT DIESEL TURBO IF SO IT THE SWIRL POT ACTUATOR THAT NEEDS REPLACING £14 FROM VX

The engine oil is kept separate from the combustion chamber by the valve seals and piston rings, either of these may be worn out.

These are seals placed on moving parts so the more miles the car has on it the looser they become, several things like letting your oil level fall too low, or operating at too high rpm can cause premature wear of these seals.

In some instances a faulty pcv valve can allow oil to enter the intake manifold when crankcase pressure is too high so check it out as well.

its the locking of the driver and passenger door with the key that operates he alarm. the only way round it is to lock the drivers and passengers doors from reaching in via the back doors or obviously locking the passenger sides before getting out by pushing th pin down then get out of the car and lock the drivers door by reaching in from the rear drivers door.

cam position censor breacking down when hot (ecotec engine)

Do you have any trouble codes?

These are prone to EGR valve, Air mass meter and crank pos sensor problems.

reconnect the sensor at the back of the disc caliper.One of them has come off-just press back on

External Input, as in a mp3 player.

1.6i 16v Club, 1998 - 2002. Standard: 30 psi front, 30 psi rear. Laden: 30psi front, 40psi rear.

If I remember there are some fuses in the side of the dash on the passenger side, open the door and remove the panel to show fuses and one of them is the cigarette lighter.

You have it in AT Mode. Push the AT button on your dash and it will turn off.

your car is leaking oil!

Goes to sport mode. Tightens suspension, and changes auto shift points to higher speeds so you rev out move in the gears.

Aim is to make the car more responsive by holding lower gears longer and to sharpen up handling (at the expense of some ride comfort)

no as it is hydrolic and these sort of clutches are non adjustable were as cable clutches you could adjust them.

It requires a star tool. There are two adjustments per light. Vertical and horizontal.

2002 JR series: You need the right size 'torque' wrench for a start they cost about $16 for a set. An oil filter. I can't recall the variety right now, 5 liters of oil. ...

Loosen right front wheel lug nuts.

Jack up the right front wheel and remove it

Brace the car with a stand

Undo sump plug with torque wrench

Drain oil

Remove oil filter from right underside wheel arch - replace with new filter

screw sump plug back in.

Put wheel back on.

Lower car to ground.

Refill oil carefully checking level doesn't exceed recommendation on dipstick (about 4.4litres)

Run car for a few minutes.

Check oil again after an hour. Top up if necessary

Buddabingbuddaboom....you are done.

A VIN number on a 1999 Chevrolet Geo Prism, as well as with all cars, are the numbers and letters that tells the history about the car. All VIN's are seventeen characters long, made up of letters and numbers. It is a unique serial number to each car. It tells the make, model, year and manufacture of the car. It can also tell where the car was built, in what year built and any extra features the car may have.