0
1982-1994 Chevy Cavaliers
1,826 Questions
Does a 1989 cavalier have sunroof drain plugs?
Yes, a 1989 Chevrolet Cavalier is equipped with sunroof drain plugs. These drain plugs help to channel water away from the sunroof area to prevent leaks and water accumulation inside the vehicle. It's important to ensure that these drains are clear and functioning properly to avoid potential water damage. Regular maintenance can help keep the drainage system in good condition.
How many fuse boxes does a 1990 Chevy cavalier have?
A 1990 Chevy Cavalier typically has two fuse boxes: one under the dashboard on the driver's side and another in the engine compartment. The under-dash fuse box houses fuses for interior electrical components, while the engine compartment fuse box contains fuses for engine-related functions. Always consult the owner's manual for specific fuse locations and functions.
How do you set the camber on a 98 Chevy metro?
To set the camber on a 1998 Chevy Metro, you'll need to adjust the upper control arm or the strut assembly, depending on the specific setup. Typically, you can achieve this by loosening the bolts that secure the upper control arm to the chassis, then adjusting its position to achieve the desired camber angle. Afterward, retighten the bolts securely and check the alignment using a camber gauge. It's advisable to have a professional alignment done afterward to ensure proper handling and tire wear.
What is the firing order for 1993 Z24 cavalier?
The firing order for the 1993 Chevrolet Cavalier Z24, which is equipped with a 2.2L or 3.1L V6 engine, is 1-3-4-2. This means that the cylinders fire in that specific sequence for optimal engine performance. Always refer to the vehicle's service manual for the most accurate and detailed information regarding engine specifications.
Where is the PCV valve located on a 1988 cavalier Z24 with a 2.8 L V6?
On a 1988 Chevrolet Cavalier Z24 with a 2.8 L V6 engine, the PCV (positive crankcase ventilation) valve is typically located on the valve cover. It is usually found near the rear of the engine, attached to a rubber grommet. You may need to remove the air intake duct or other components for easier access.
How do you remove the center console in a 1989 Chevy Cavalier Z24?
To remove the center console in a 1989 Chevy Cavalier Z24, start by removing any screws or bolts located in the storage compartment and under the armrest. Next, carefully pull up on the console to disengage it from the clips holding it in place. You may need to disconnect the wiring for any accessories like the cigarette lighter or power outlet. Once everything is disconnected, you can fully lift the console out of the vehicle.
Torque specs 89 Mitsubishi truck 2.0 liter cylinder head?
For a 1989 Mitsubishi truck with a 2.0-liter engine, the cylinder head bolts should typically be torqued to 50 ft-lbs (foot-pounds) in a specific sequence. It's important to follow the recommended torque sequence and to use a torque angle specification if applicable, which may require an additional 90 degrees after reaching the initial torque. Always refer to a service manual for your specific model to ensure accuracy. Proper torque is crucial for preventing gasket failure and ensuring engine integrity.
How do you replace a 1999 Chevrolet Cavalier head gasket?
To replace the head gasket on a 1999 Chevrolet Cavalier, start by disconnecting the battery and draining the coolant. Remove the intake and exhaust manifolds, along with any components blocking access to the cylinder head, such as the alternator and power steering pump. Carefully unbolt the cylinder head, clean the mating surfaces, and install the new gasket. Finally, reassemble all components in reverse order and refill the coolant before starting the engine.
How do you fix the horn in a 1985 Chevy Cavalier?
To fix the horn in a 1985 Chevy Cavalier, first check the fuse related to the horn in the fuse box and replace it if necessary. If the fuse is intact, inspect the horn relay and connections for any corrosion or damage. Next, locate the horn itself, usually positioned behind the grille, and test it by applying direct power from the battery. If the horn still doesn't work, you may need to replace it with a new one.
Do they still make mercurochrome?
Mercurochrome, a topical antiseptic containing mercuric ammonium chloride, is no longer widely available due to safety concerns regarding mercury exposure. While it was commonly used in the past for minor cuts and scrapes, its use has largely been discontinued in many countries, including the United States. Some variations or similar products may exist under different names, but true mercurochrome is not commonly manufactured or sold.
What is the size Head Bolts on a 2000 Chevy cavalier 2.2?
The head bolts on a 2000 Chevy Cavalier with a 2.2L engine are typically 10mm in diameter. They usually require a 12-point socket for removal and installation. It's important to follow the manufacturer's torque specifications and sequence when reinstalling them to ensure proper sealing of the cylinder head.
What is the head bolts torque specs for a1994 v max 600 snowmobile?
For a 1994 Yamaha V-Max 600 snowmobile, the head bolt torque specifications are typically around 22 ft-lbs (30 Nm) for the initial torque. After the initial torque, it's important to follow a specific sequence and pattern for tightening, usually involving a final torque step of approximately 30 ft-lbs (40 Nm). Always consult the service manual for the most accurate and detailed specifications.
Where is crankshaft sensor on a 1992 Chevy Cavalier?
Oh, dude, the crankshaft sensor on a 1992 Chevy Cavalier is located near the crankshaft. Surprise, surprise! It's usually around the bottom of the engine, close to the crank pulley or the flywheel. Just look for a little sensor hanging out down there, doing its job of telling your car's computer where the crankshaft is at all times. Nice of it, right?
How does 2 4 6 1 3 equal 88 with only two operational signs?
Well, let's think about this like a happy little math problem. If we add 2 + 4 + 6, we get 12. Then if we multiply that by 3, we get 36. Finally, if we add 1 to that, we get 37. If we multiply 37 by 3 again, we get 111. By subtracting 23, we get 88. And there you have it, a beautiful solution with just two operational signs!
Your 1998 Lincoln continental idles way too high any suggestions?
Try disconnecting the Throttle Position Sensor (TPS). It is located on the throttle body. A small black sending unit with an electrical connection coming out of the top. On my 1998 Lincoln Continental, disconnecting the TPS brought the idle back to normal. Plugging it back in caused the idle to shoot up high again. It is a sending unit that tells other computers in the vehicle the position of the throttle plates. Other calculations of fuel, air, etc. are apparently made based in part on what this sending unit is saying. I guess unplugging it shuts it up. Of course, it will need to be replaced so that it can again begin sending useful information.
Update: I changed the TPS (buy it online if you can wait. Its a bit expensive at Ford). The car ran perfectly after about 30 seconds (so the computer could reset probably). To replace the TPS you will need to take a few parts out. First, remove the air cleaner, disconnecting any vent pipes and electrical connections on it, and get it out of the way. You will then see four bolts on the throttle body (the thing with the two butterfly flaps in it). Unscrew the four bolts and take them out. Then very carefully lift the throttle body off of the gasket. You don't have to take it all the way off. In fact, because it is still connected to the throttle cable and all of the other throttle cable related parts, you can at best tilt it up so that you can get access to the two screws that hold in the TPS. Once you tilt the throttle body up, unscrew the two bolts holding the TPS in and take them out. BE VERY CAREFUL. If you drop one of the screws it could go down the intake. That would be a major problem. However, if you carefully remove the screws and set them aside, the TPS comes right off. Put the new one on, making sure it seats correctly and screw the two screws back in. Then reseat the throttle body and put the four bolts back in. Reinstall the air cleaner and you are done. The whole operation can be done in about 20 minutes.
Throttle plate may be sticking
Where are the most common places for coolant to leak on a BMW 325?
The most common places for coolant to leak on a BMW 325 are from the water pump, radiator, hoses, thermostat housing, and expansion tank. It's important to inspect these components if you suspect a coolant leak to prevent overheating and engine damage.
96 Toyota corolla idles too high when cold?
This happens on new cars as well as older models, when the car warms up the idle should drop. When its cold the fluids in the motor get thick so it works alittle harder until it thins out with the heat
If your 1992 Buick Skylark with a new motor, thermostat, radiator, and gaskets is still overheating, the issue could be related to the water pump, a malfunctioning cooling fan, or a head gasket problem. It's also worth checking the cooling system for any air pockets that may be preventing proper circulation. Consulting a mechanic for a pressure test or further diagnostic can help identify the root cause.
What are the steps in replacing an ignition lock cylinder on a 1990 Cavalier?
Hate to tell you this, but you have to take the steering column apart. under the horn there's a bolt, but you need a special tool to put it back on... took me about a day and a half to fix it up on mine and now it just needs fixing again... so I just bought a club and hoped nobody found out it wouldn't lock.
How do you change the front and rear speakers and the audio deck in a 2000 Chevy Cavalier?
if you send me an email i will be able to tell its kinda tricky because you have to remove the top panel of the dash to take out the stereo and you dont want to deploy the airbag in the process, my email is bigclop2@yahoo.com
How do you replace a fuel pump in a 1991 Chevy Cavalier?
The fuel pump is located in the fuel tank as with virtually all cars nowadays. There is a certain degree of danger working on or around a fuel tank. But, if you want to do this yourself, You will need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
or you can go to www.auotzone.com and go to repair manuals and it will show you exacly what to do and you can print it if you need to
How do you remove non-Bose rear speakers from a 1997 Nissan Maxima?
I have had to remove the lower section and upper section of the back seat to start this process. To do this slide your hand along the bottom edge of the lower seat until you feel a ring, now pull this towards the front of the car (Remove lower section of seat from car now). Next there is a screw on both bottom sides of the upper seat section that connects the seat to the car, Remove these two screws. Now I found two more screws inside the panel that folds down in the middle of the upper section of seat. Lower the panel and pull the fabric retainer up and away from the trunk wall. These two screws were in the car at a ridiculous tightness, I literally had to get my biggest screw driver to turn these out. Once these screws are out then the seat is free and remove from car. Now the reason these need to be removed is because Nissan mounted the speaker grills right to the rear window deck. In order to remove this you need to remove the seats, and now the side panels that sit next to the rear window and hold down the rear window deck. These come off fairly easy, Just start at a corner and wiggle and pull until each bracket seperates from the car. Now the rear window brake light needs to be removed in order to remove the rear window deck. This I have not figured out yet how to remove without just breaking it off out of frustration (hence the reason I'm on the net looking for answers.)
UPDATE by 6eStanza
To complete the removal of the rear deck to access the speakers below, you need to crawl into your trunk with some pliers and a flashlight. If you look up to where the speakers are you should see a couple of white retaining clips. If you squeeze the exposed end with the pliers (careful not to break clips) and push up on the deck simultaneously you should be good to finish your project. Thanks a lot Nissan for making that so flippin complicated.
The center brake light mount is actually removed by turning the whole assembly counter-clockwise about 1/8 of a turn.
Try to use the Nissan speaker adapters plugs so you don't need to cut wires and mess up the electric system, you can get those from eBay or amazon.
Do they still make springmaid towels?
Don't think so. I've been trying to find a replacement without luck.
