Car Electronics and Lights

To turn off the airbag light on a 2000 Daewoo Matiz, you should first check for any fault codes using an OBD-II scanner, as the light may indicate an issue with the airbag system. If there are no faults, you can try disconnecting the car battery for about 15 minutes to reset the system. After reconnecting the battery, the light may turn off if there are no underlying issues. If the light remains on, it's advisable to consult a professional mechanic for further diagnosis and repair.

To replace the headlight bulbs in a 2001 Acura CL, first, open the hood and locate the headlight assembly. For the bulb you need to replace, twist the bulb socket counterclockwise to remove it, then pull out the old bulb. Insert the new bulb into the socket without touching the glass, twist it clockwise to secure it, and reconnect the wiring. Finally, test the headlight to ensure it’s working properly before closing the hood.

The turn signal fuse in your 2002 Chevy Express 1500 van may keep blowing due to a short circuit in the wiring, a faulty turn signal switch, or a malfunctioning component in the turn signal or lighting system. Corroded connections or damaged wiring can create excess resistance, leading to a blown fuse. It's also possible that there are issues with the trailer wiring harness if equipped, which can cause similar problems. Inspecting the wiring and components for damage or wear can help identify the root cause.

In a 2001 Nissan Xterra, the central door lock relay is typically located in the fuse box under the dashboard on the driver's side. You may also find it in the engine compartment fuse box, depending on the specific wiring configuration. It's advisable to consult the vehicle's service manual for precise details on locating and identifying the relay.

In a 1995 Ford F-250 with a 7.3 Power Stroke diesel engine, the engine control module (ECM), often referred to as the computer, is typically located on the driver's side of the engine bay. It is mounted on the inner fender well, near the battery. Accessing it may require removing some components for better visibility.

The turn signal flasher on a 2003 Ford Excursion is typically located under the dashboard, near the steering column. It can often be found in the fuse panel or directly attached to the steering column assembly. To access it, you may need to remove a cover or panel beneath the steering wheel. If you’re having trouble locating it, consulting the vehicle's manual can provide specific guidance.

Well, honey, changing a brake light bulb on a Mitsubishi Galant is as easy as pie. Just pop open the trunk, locate the back of the light assembly, twist out the old bulb, pop in the new one, and voila! You'll be lighting up the road like a Christmas tree in no time. Just remember to test it out before you hit the road, unless you're into getting pulled over by the fashion police.

Oh, isn't that a happy little question! The fuse-relay for the electric Power Steering on a 2003 Saturn Vue is typically located in the fuse box under the hood of the car. It's like a little friend that helps the steering work smoothly. Just take your time, follow the wires, and you'll find it in no time. Just remember, there are no mistakes, only happy little accidents!

Luck is to open as unprotected is to panic

Watts of Power are not 'drawn', it just exists, or is generated by electrical interaction in the circuit.

Amperage is 'drawn' by a load.

The equation you're looking for is: P = VI, so P = (10)(120) = 1200 Watts, or 1.2 kW.

If you have a Three-Phase circuit, the eq changes to: P = VI(square root of 3).

1.73 is usually good enough to use as a value for the sqr 3.

(im the one asking ^That^ Question BTW) the kind of lights these are, are the kind you would install under your car... i have 3 tubes with wires at the end of each, a switch but no transformer do i need it? And also can i just stick the wires into the outlet or would that kill me? Ahaha

Thank You Everyone!

This question cannot be answered without further information.

Please ask this question again and be sure to say where the fan controller relay is fitted: is it in a car or other vehicle? It in a home? What make is it?

You will get reduced amperage (or output) from the alternator. A alternator rated at 80 amps would probably only produce 50-60 amps. If a diode in a rectifier is shorted, then the alternator output would be greatly reduced or possibly no output at all.

A good solder connection is shiny, smooth, and free from any pits, cracks, or irregularities. It should also have good adhesion to the components being joined and be strong and reliable. Additionally, the solder should have flowed evenly and completely join the parts without any excess solder.

Conrad Hubert invented the flashlight in response to the need for a portable and reliable light source that could be used during power outages and in other situations where a quick and convenient source of light was necessary. He saw an opportunity to create a product that would provide illumination on the go and revolutionize how people could light up their surroundings in various situations.

A traditional hair dryer evaporates water from your hair using a stream of heated air blown into the hair. The temperature and time of drying must be carefully controlled to avoid damaging the hair shafts. Newer hair dryer technology uses electrical charges (ions) to strip water molecules from your hair, which reportedly is faster and less likely to damage hair (split ends, frizzy, dull). Reportedly it removes moisture from the surface of the hair while leaving some moisture within the hair shaft for improved sheen. Some manufacturers claim that using crystals of the mineral tourmaline in the construction of the dryer produces a superior electrical charge, while using ceramic heater elements produces superior hot air, so the latest high-priced dryers boast "Ceramic Tourmaline Ionic" technology.

Low melting pointsolder used for PC boards is a must. The components on the board are heat sensitive and can be destroyed by high heating when they are soldered to the PC board traces. This is mostly done by machines now but the solder still has to be the lowest melting point possible.

Because, as you drive, the rolling friction of the road increase heat in the tires and that heat warms the air in the tire and the air expands , increasing the pressure. Manufactures, recommend a max psi COLD. They know that the pressure will rise after driving .

20,000 volts = 20 kv

One watt is 0.001 kilowatt. 65 watts is 0.065 kilowatts. It does not matter what the voltage is - watts are watts.

The U.S. military was the first to develop and use GPS technology in the 1970s for navigation and positioning purposes. It was later made available for civilian use in the 1980s.