0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
How do you replace a fuel pump in a 1995 Chevy Beretta?
the fuel pump is inside the gas tank. you have to drop the tank, and there is a locking mechanism around the sending unit. undo that and pull the sending unit out. be very careful not to damage any of the fuel lines or wires to the pump. the fuel pumpis a silver color cylinder towards the bottom of the sending unit. twist the pump i do believe to the left and pull it off. the screen on the bottom is just pressed on so you can get that off with a screwdriver but be careful! after the pump is off replace the new one exactly the same way you took it apart and replace it in the tank. now most new pumps come with an o-ring that seals the sending unit so you don't leak gas. replace the sending unit locking mechanism and replace the gas tank in the car, mak sure that your intake and return lines are right and then turn the key to run and you should a humming noise which means that the fuel pump is working. it may take a couple of times trying to start it before it starts and that's do to the fuel system repriming itself. good luck!
Where is it stuck? on full or empty? if on full you got a bad ground, if empty you got a bad float.
Can you put Corvette rims on 93 beretta?
no you can not put corvette rims on a Chevrolet berretta. Reason being that corvettes are rear wheel drive and berrettas are front wheel drive. The dimensions are completely different.
Where is the crank sensor on a 1989 Chevy Beretta and how do you fix it?
the crank sensor is located on the back of the engine aprox. 1 inch above the oil pan. there is one bolt holding it in place, after removing the bolt pull the sensor out installation is reverse
What is the gap on spark plugs for a 1988 Chevy beretta 2.8 liter?
the gap is 35 assuming you have the 2.0 4 liter
Where is Vehicle Speed Sensor located on a 1991 Econoline 350?
On the 91 - 96 E350 there is no VSS. It is called a ABS Speed sensor and it is located on the top of the rear differential. I had the misfortune to be missled with the VSS theory as well and several weeks and a lot of wasted time and money, in frustration I just pulled the ABS speed sensor off and replaced it. My ABS light went out and my automatic transmission shifts well to include the overdrive. I hope this helps you.
How do you reset the check engine light on a 1994 Chevy Beretta?
The check engine light indicates a problem with the emissions system so to permanently clear the code you must have the codes read and correct the problem, it is most likely a faulty sensor. Auto parts stores at least the big chains can read the codes for you and also help in clearing them when you are done, however you can disconnect the neg battery cable to reset the computer but be careful GM radios will go into security lock when power is interrupted and need to be unlocked at a dealer. If you are trying to get a smog certicicate on the vehicle and it wont pass due to the check engine light simply resetting it wont help because you will have to log around 100 miles before the smog computer will test it again and by then the light will be back on.
Where is the ECM located on a Chevy Beretta or Corsica?
Remove the glove box and look under the dash. You should see a big metal box. That's it.
Where is the coil ignition located for 1991 beretta 3.1?
front of engine block right next to the starter.
How can you adjust the clutch in a manual transmission 1996 Chevy Beretta?
most clutches need free play adjustment with manual linkage is next to left side of transmition
It is next to the computer behind the glove box.
Check the fuses and blower relay. Also check to make sure that the replacement blower motor has not failed. If these items are good then the electrical system will need to be tested to see where the blower system is losing power.
Would an un plugged coolant temp sensor cause misfiring on 1994 Chevy beretta 3.1?
No it would not only a bad (ICM) Ignition control module or a bad injector would...
How do you replace the brake lines on a 1994 Chevrolet Beretta?
Measure each brake line and go to the parts house and get the necessary lines. You will need a tubing bender. Remove the old lines one at a time and bend as needed. install the lines and then fill the master cylinder and bleed each wheel.
Where do you find the cooling fan relay control circuit on a 96 Chevy Beretta?
In my '96 beretta the cooling fan relay switch is located on the drivers side strut tower. That may not be the problem. If your fan still won't work after changing the relay switch try the coolant temperature switch/sensor.
How do you replace the serpentine belt on a 1995 Chevy Beretta?
put a socket wrench,on belt tensioner,there should be a small square hole there,that fits a socket wrench,lift upwards,careful not to slip wrench,then belt should lift up and come off,slide on new belt,lift upwards again,then let down slowly once belt is on.your done.easy.
What are the torque specifications for the intake and rocker arms on a 1999 Chevy Malibu LS?
The lower intake is 10 ft lbs the upper is 18ft lbs. If you go to autozone.com and read there specifaction area its listed there. That's were I found it!
How do you replace the outside driver's side door handle on a 1995 Chevrolet Beretta?
When you open the door, on the inside of the door (the part where the door striker/latch is) there's bolts you remove. It seems to me there's a panel that runs along there as well that you have to remove.
My old handle broke so I just pulled the remains out from the inside of the door. Start by removing that panel on the door frame, and look for it's bolts. Buy a Haynes manual if you're still confused.
How do you get to your fog lamps to replace?
alright these are fun.....you have to take off the plastic covers underneath. There should be two torx bolts that are holding in the assembly that you get to from the front. after this reach up from underneath and push out the assembly through the fender. you wont have much room to work on it but its just enough to replace it. Test before putting back together because its a pain trying to get them out. the bulb will have one wire coming from it with a metal slab at the end of it. the slab will slide into what looks like a splice connection. there is a gound wire that will go to the metal flanged washer on the back of the fog light assembly. make sure this is clean and gets a good connection, i had to wiggle mine to get a good connection so it would work. good luck!
Where is the oxygen sensor on a 1994 Chevrolet Beretta?
The oxygen sensor is in the rear exhaust manifold. You should be able to see it by looking behind the engine from inside the engine bay.
Where could you find a diagram for the wiring system for a stock stereo in a 1989 Chevy Beretta?
go to a place that sells car audio, like best buy or somthing similar. Just guess and check. I have a 88' Beretta GT and the stock stereo wires were as follows; RED=Ignition, Yellow=Constant Power, Black=Ground, Dark Blue=(-) Right Rear Speaker, Light Blue=(+) Right Rear Speaker, Then there is light green, dark green, gray, gray with white stripe. But not sure which speakers those are to but I know they are for the speakers.
