0
Chevy Cavalier Z24
Cavalier Z24 is a sport-themed style of the compact Cavalier. The Z24 model traversed two generations of the model line. Besides using a powerful V-6 engine, it offers five-speed manual transmission and an optional three-speed automatic transmission.
1,493 Questions
How do you bleed the brakes for a 1991 Chevy Cavalier wagon?
If it has antilock/traction control system, you have to have a professional bleed them for you.
You need: A new bottle of approved brake fluid. A box-end wrench that fits the bleeder valves. A hose that fits over the bleeder valve. A can or jar. A helper.
Take the cover off the master cylinder. It's divided in two sections. One for the rear brakes and one for the front. Make sure it's full. If it gets too low, it will suck in air - then you'll have to start all over again.
Start at the furthest wheel from the master cylinder (rear passenger side). Have your helper push and hold the brake pedal down. Now open the bleeder valve and let the fluid squirt out into the jar/can (small hose over end of bleeder valve). The brake pedal should now go down all the way to the floor. When it's done squirting, tighten the valve again. Tell your helper to release the brake pedal and pump it a few times. Next, tell them to push and hold down the pedal again. Open the valve and let it squirt out. Close the valve. Let go of brake pedal. Pump brakes . . . Keep doing this on each wheel until you don't hear or see any air bubbles coming out of the valve and the fluid looks clean.
Next, do the drivers side rear, then the passenger side front, then finally the drivers side front.
Make sure you keep checking the fluid level in the master cylinder. As you bleed the brakes, you'll have to keep topping it off.
Replace cover on master cylinder (push in the rubber balloon/accordion things under the cover - these pop out as your fluid level gets low).
Dispose of left over brake fluid. Don't save it. Once you open a can, the fluid absorbs water and it's no good after a while.
Check brake pedal movement. It should not go to the floor and feel strong.
Check for leaks. Test drive the car. Slow at first (just to make sure).
Where is the air intake control valve located on a 2000 Chevy Cavalier Z24?
There is no "air intake control valve" persay. On the throttle body you have, Idle Air Control Valve it is square looking and right in front. The IAC valve does just that,controls the idle. It has 4 wires.There are a couple of ways to test it.The easy way is with an ohmmeter.Unplug it and check resistance across terminals A and B, then across C and D(on the valve,not the plug). Each resistance check should indicate 40 to 80 ohms. If not replace the IAC valve. Simple to change,no ajustment required. Also,there is a TPS (Throttle Position Sensor,on the side that looks round), MAP Sensor(manifold air pressure sensor,it is held down with one of the throttle body mounting bolts on a little bracket by itself in the front).3 wires and a short vacume line. AIT Sensor (Air Intake Tempeture Sensor).On the big round tube between the air filter box and the throtle body.And the only thing that would be close to what you are wanting to know is the throttle valve itself inside the throttle body bore..(Connected to the the throttle cable)
How do you reset the computer on a 97 Z24 Cavalier?
unplug the battery for about half an hour and that will reset the car.
What horse power is a 316 BMW?
From "http://en.allexperts.com/e/b/bm/bmw_3_series.htm": 1982-1987 316 - 1.6 L M98 I4, 90 hp (66 kW) 1982-1990 316 1.8 - 1.8 L M10B18 I4, 90 hp (66 kW) 1987-1991 316i - 1.6 L M40B18 I4, 102 hp (75 kW) So it depends on the model, i suppose.
What is the egr on a 1997 Chevy Cavalier z24?
Basically the EGR (Exhaust Gas Recirculation) valve that lets exhaust fumes return to the combustion chamber to be re-burnt if the o2 sensor tells the computer their are to many gas fumes in this exhaust pipe not getting burnt. The computer then tells the fuel injectors not to stay open as long. These "Quad 4" engines were found to be way below the acceptable level. In mid-1999 model, the EGR was removed entirely. So if your car has one(EGR) 95-mid-99 It will have to remain plugged in just to keep the check engine light off.If you install a mid 99-newer engine, Just tuck it somewhere out of the way. Most of the time if you get a trouble code with the EGR it can be solved by removing it and cleaning exhaust funk out of the passage way. In 1999 they just changed the exhaust manifold gasket. It has one less hole in it.
Starting Chevrolet Cavalier grinding?
sounds like you have broken some teeth on the fly wheel gear.Hopefully it on the starter itself which is easier to replace.
Where is the heater core located on a 2000 Concorde and how can you fix it?
The heater core is underneath the dash in the middle section right behind the console. You can fix it by removing the dash.
How do you change the alternator for a 1988 Chevrolet Cavalier Z24?
Head down to your local auto zone, you will need to rent a tool called a "serpentine belt tool"...about 25 dollar deposit I believe. Insert that tool into the side of the belt tensioner, there will be a square hole. Rotate the belt tensioner until you can slip the belt off one of the pulleys. Now disconnect the wiring on top of the alternator, one small nut I believe its a 10mm or 8mm. Then remove both mounting bolts, forward one is a 10mm and the rear I believe is a 13mm. You can now grab hold of the alternator and lift it off the engine. There will be one more wire to disconnect once you get it off, its on the bottom...just a clip connector. You can now remove the alternator from the engine bay. Installation is the reverse process.
How do you disconnect the stock anti-theft system on a 1993 Mazda 626 ES?
My Mazda is a 94. There is a black switch near the hinge on the driver's door about 6" from the floor board in front of the fuse box. The down position turns it off.
What are the 1989 cavalier Z24 specifications?
what specifications? oil pressure? horse power theres alot u need to be alot more spific
How do you replace torque strut mount on a 1999 Chevrolet Cavalier?
Some people call it the "Dogbone" mount. Because that is what it resembles. It is located underneath the engine on the passenger side. It prevents the engine from spinning around when you give it gas and go.Simply remove the 2 bolts (15mm i belive) that mount it,knock it out with a hammer or pry it out with a screw driver(your choice), put in the new mount,put the two bolts back in and go...simple.
How do you replace a convertible top on a 1994 Chevy cavalier Z24?
Leave it to the pro's. There are many things that need to be done and checked/replaced. So leave it to someone that does this sort of thing everyday. These cost to much to gamble on a novice.
How do you change a water pump in a 2000 Cavalier Z24?
It is driven by the timing chain and is a pretty big job if you have never done it. Get help form someone that has done it before. You risk destroying the engine if not done right. But you will need (2) 8mm bolts to hold the cams in time.
1995 Jeep Wrangler oil pressure is very high 80 psi What could it be?
The oil pressure sending unit could be bad. Or the oil pressure gauge could be bad, but normally gauges don't fail............I would have someone check out the oil pressure sending unit.
I had the same thing with my 1995 z24 2.3. When the car was cold it made the grinding noise and i changed the trans oil with ams oil trans oil and its smooth as silk know. Make sure you use manual trans oil
How do you check the transmission fluid in a 95 Chevy caviler z 24?
theres no real way to, there the fill hole on top of the tranny under the break fluid tank but theres no dipstick...its a Chevy
Where is the fuse for the horn in the 1995 Chevy Cavalier?
open the divers side door and there is a fuse pannel on the side of the dash and it has lables on wich fuses do what
How much will it cost to do a Z24 swap into a 2002 2.2 cavalier?
More than the car is worth unless you have lots of tools and time and do it yourself. The motor mounts would have to be the same or make new ones. You would have to change your PCM and possibly all of the wiring. If you are going from auto to man. or man. to auto you open a door for alot more problems. It could be done but unless you have torches, air comp. and air tools, proper lifts and stands, jacks, sockets, a garage for two to three weeks and a buddy who knows how to rewire it's just not worth it. A haynes manual for each car would help alot. If you don't do it yourself it could cost $2500 - $5000 or more. Buy the manuals at atuo zone and just see how much is involved in just a rebuild. Hope I helped. More than the car is worth unless you have lots of tools and time and do it yourself. The motor mounts would have to be the same or make new ones. You would have to change your PCM and possibly all of the wiring. If you are going from auto to man. or man. to auto you open a door for alot more problems. It could be done but unless you have torches, air comp. and air tools, proper lifts and stands, jacks, sockets, a garage for two to three weeks and a buddy who knows how to rewire it's just not worth it. A haynes manual for each car would help alot. If you don't do it yourself it could cost $2500 - $5000 or more. Buy the manuals at atuo zone and just see how much is involved in just a rebuild. Hope I helped.
The timing belt broke and now you can't get your 94 Suzuki sidekick timed what do you do?
http://www.kick-fix.com/t-belt/tbelt.html
no need to buy an FSM or post this answer a million times. so i have it here.
1 time.
valid for 89 -98 1.6L Suzuki' sidekicks and Geo trackers (same motor )
Why would a new starter on a 1998 Mercury Topaz not seem to be getting any current?
It could be a bad starter relay, faulty wire(s)/switch(s) and/or dirty connections. I would check the starter relay and connections first. If everything else checks out, it just might be the starter itself.
How unlock the radio in a 1997 Chevy Cavalier?
I cant type very good so I'm not going to try to explain it. If you know the code number... do a "GOOGLE.COM" search. The procedure is listed may places. If you dont know the code that was used, a dealership may be in your future.
Where is o2 sensor located in a Chevy Cavalier?
there is two of them, ones on the top and there is one on the bottom of the engine.
Here is how you would change them.
http://www.ehow.com/how_5059297_change-oxygen-sensor-chevy-cavalier.html
What does a certain light mean on the dash?
which light are you talking about? you need to add more detail
