Why does my 1999 corvette run hot you just had my head gaskets replaced you need help?
This Engine Has Aluminum Heads. They Should Have Been Tested For Cracks And Surfaced To Be Sure Of No Leaks Or Warpage. If The Engine Ran Hot & Blew Gaskets, You Could Have Craked Heads, Or More Simple A Thermostat Not Opening, Not Enough Coolant Flowing ( Radiator Stopping Up ) Weak Water Pump, Not Likely Though, It Would Leak. Run It Into A Radiator Shop. They Can Pressure Test It, To See If You Have A Leak( Internal Or Otherwise ) Also Your Fan Clutch May Be Bad===The Fan Is Bolted To It Then It Is Bolted To The Water Pump. It Works Like This, When The Engine Is Cold It Lets The Fan Not Run Very Fast So The Engine Will Get To Operating Temp. Faster Then When Engine Get Hotter It Will Not Engage And Run The Fan Faster Keeping The Engine Cooler. Well Heck. Radiator Shop Is Best Bet.
Where is the temp gage sensor on a 94 lt1 Corvette?
It should be on the right side cylinder head ( passenger side) between and just above #6 and #8 spark plugs. This is where it is on my '95 Corvette.
How do you install a grant steering wheel on a 1992 camaro?
Do you have all the adapters and extension housings?
How much horsepower does a 350 79 Chevy pickup have?
It's impossible to say without measuring it on a dyno.
If the truck is absolutely 100% factory stock - no mods, no rebuilds, nothing - look up the original HP for that model truck online (try mortec.com).
Then take off 1% of the factory HP for every 10K miles on the engine. (This doesn't really apply to engines under 50K miles, but makes a good estimate for high mileage engines.)
How do you install c5 Corvette sunvisior?
I believe it is just like the C6 with a couple screws holding each in. I know that there are quite a few people that take them off as they really never get used. There is a member over at Smokinvette.com that has pictures of his Corvette without visors.
How do you get to the power antenna on a c5 to remove it and put in a new one?
Remove the right most tail light. Two screws hold the light in place. The antenna is directly behind the light.
Where is paint code on 1978 Corvette?
Inside the driver's side door on the forward part of the frame (above the door hinges, directly to the left of the headlight switch). There is a metal plate with the paint codes stamped on it.
What is the horse power of a 2007 Chevrolet Corvette grand sport?
Chevrolet didn't make a Corvette Grand Sport in 2007, they first brought out the C6 generation version of the Grand Sport in 2010. The 2010 Grand Sport puts out 436HP.
What are the advantages of a dry sump oil system?
the oil is not whipped by the crankshaft which causes drag and friction, not to mention it foams oil uo second the oil stay cooler in a remote oil tank and oil is not exposed to as much combustion blowy-by contamination. third if you are racing around turns with high g force the oil can lean in the pan and starve the oil pump momentarily
Where can one find photos of an 84 Corvette?
A quick browse of images on Flickr or Pintrest will offer thousands of photos of a 1984 Corvette. Despite being nearly thirty years old, this model is still popular among collectors.
How many gallons does the gas tank in the 2010 Chevrolet Corvette hold?
The gas tank on the 2010 Chevrolet Corvette holds 18.0 gal..
How do you get a 1990 corvette to start if it turns over and the battery is good?
To get a 1990 Corvette to start if it turns over and the battery is good, check to ensure the fuel filter is not clogged. You also need to ensure it has plenty of gasoline.
Are there any bulbs in the dash cluster on a 1988 Corvette you can replace?
Yes. Pull the plastic and you will see that they are easy to get too. Just becareful pulling them out. Replacements can be found at your local parts store.
The Chevrolet Corvette is a high performance American sports car made by General Motors beginning in 1953. All of the 1953 Corvettes were made in Flint, Michigan with first two production units completed on June 30, 1953. The 1954 to 1981 Corvettes were made in St. Louis, Missouri. The last Corvette built at St. Louis was completed on August 1, 1981.
In 1981 there was a two month overlap in production of Corvettes as some were made in St. Louis and the remaining were made in Bowling Green, Kentucky. The first Corvette completed in the Bowling Green plant rolled off the line on June 1, 1981 and all Corvettes have been made there ever since. In 1983, only 44 Corvettes were built (no actual production run for that year) but only one of them still remains which is housed at the National Corvette Museum. The Corvette is considered America's premier sports car and has had one of the longest production runs of any car in history.
Thank You!
I knew that corvettes were made in flint hills for a while but i didn't know that they were made in St. Louis until 81!I have also wanted to know when the first was made.
From,
A big corvette fan!
How do you remove the headliner from a 1992 Corvette targa top?
Corvettes suck. Unbelieveable the way they are designed.All rubber is guaranteed to rot out.
Apart from the main circuit breaker in the fuse box, there's a separate fuse box with 4 fuses under the passenger side dash. You have to remove the hush panel and look all the way in the back to see it.
Where is the horn located on a 1999 Corvette?
There are two horns, on low tone and one high tone. They are on the passenger side behind the back splash panel.
Where is the ac power relay located on a 1991 Chevy Corvette?
The AC power relay is located behind the right side of the dash on a 1991 Chevy Corvette. It is on top of the plenum.
Why won't your power windows work in your 1975 corvette work?
There are a few reasons why the power windows on a 1975 Corvette won't work. A few of these would be a wiring issue, a motor issue or the fuse is blown.
Where are the buttons to open the rear hatch on a 1987 corvette?
one inside the center console and one on the latch side of each door
There usually is a drain petcock on the bottom middle or end, however the are now made of plastic and if they break it is a hassel to find a new one and then you may have to pull the radiator to get at it so I usually pull a end off the lower hose.