0
Chevy G20
Manufactured by the American automaker General Motors Company for the G-Series product line, the Chevy G20 was a passenger van powered by a 4.3 liter V6 engine, which can generate up to 165 horsepower.
1,037 Questions
Where is the fuel pump relay on a 1993 Chevrolet G20 van with a 305 v8?
The fuel pump will be located inside of the fuel tank. If you need to replace the part, you will most likely need to go through the trunk.
It is possible the antenna is bad but it is probably the receiver that has gone out. The receiver is under the dash, above the gas pedal, behind the ash tray. It is silver with wires and the antenna plugged into it. They are getting harder to find for a reasonable price.
What is the firing order for a 1993 Chevy G20 where the number 1 is on the distributor?
click on edit answer to see the layout,small block and big block Chevrolet engine firing order is 1-8-4-3-6-5-7-21 is the post facing #1 cylinder (front drivers side) then hook up number 8 on distributor which is clockwise then 4 and so on. odd cylinders on drivers side of engin ...1,3,5,7, and passengers side are 2 in the front then 4,6,8
6 5 3 7 4 2 8 1
rear
8 7 6 5 4 3 2 1
front
hope this helps.
Where is the blower motor located on a 1997 Chevy Astro Van?
The Blower motor is under the hood, passenger side. It has a purple wire attached.
Where is the crank sensor in a 1991 Chevy 5.7l v8?
1991 probably doesn't have a crank sensor, it probably has a reference in the distributor.
What year is a 454 engine with a casting number 14015445?
For this question to be answered you must provide the number that is above the timing chain cover.
it is a 1978-1990 2 or 4 bolt main
I am answering my own question. After reviewing several websites, including this one, I suspected that the relay/resistor might be the culprit. This is a small box under the hood, over on the left hand side, screwed into the heater core box cover(???) to the immediate right of the blower motor. It's the only relay over there, and is above everything else, so it's easy enough to figure out. There are five wires leading to it, heavily wrapped with black tape. It is easily separated via a two part housing that "clicks" together. In my case, when I took it apart, it was instantly obvious that both the relay resistor half and the plug-in wiring harness half were both cooked (lucky me!) Note that there was no hint of this looking at the outside of the housing; it was a stealth burn-out. The relay resistor can be bought at any good auto parts store, but the combination is apparently a dealer item and pretty pricey, so I hit a local junkyard and got two of them for basically nothing (I took each one apart first to make sure it wasn't fried, before I clipped them out). After that it was just a standard wiring splice job. Be sure to disconnect the battery before you start, as the red wire stays hot even if the van is completely off. If you have the part and proper tools, it's about a 45 minute job.
Where are the fuses for a g20 conversion van?
The G20 conversion van's main fuse box is beneath the dash board on the left of the steering column. You can view it if you bend down and look under the dash to the firewall.
How do you repair a stuck horn on a 1991 Mazda Protege?
Replace the horn relay.
Also look at the foam padding in the steering wheel,it may be worn out.
My 99 escort had a stuck horn...pull out the foam switch in front of the air bag, move it around a little, clean the contacts, then test it with a multimeter to make sure it un-stuck itself.
-Matt http://www.olszak.net
Where is the freeze plug on a 2000 Mercury Sable and how do I change it?
There is more then ONE suggest looking [http://www.themotorbookstore.com/taurus1.html Here] Happy Plugging :-)
Where is the wiper motor on a 94 Chevy conversion van g20?
Behind gauge cluster, right side of steering column
Hey, I had a problem like this and solved it. Take a test light and check at the ecm for power (with the key on) at the orange and black wire. My car had a broken connector in the engine compartment that feeds power to the ecm. Take some electrical tape and wire covers off. It is where two large orange wires meet three small orange wires. After repairing that, my car started right up. Good luck, Ken- Martin Auto Body
How can you tell if the master cylinder is bad on a 1988 Chevy G20 conversion van?
If when you are stopped for a light, the brake pedal just slowly goes down, it is time to replace the m/cylinder.Or if it is leaking.
How do you remove the carrier bearing from your 1989 Chevy three quarter ton van?
Remove rear cover and drain oil. Remove rear wheels and break drums. Remove center pin between axles by unscrew pin in carrier. Push axles in slightly and remove 2 C clips. Pull axles out. Remove 4 bearing cap bolts. Use large pipe or jack handle to force carrier out. Do not let it fall. Use puller to pull bearings off
you ran it too hot and burnt out some gaskets and possibly warped the heads
