0
Chevy G20
Manufactured by the American automaker General Motors Company for the G-Series product line, the Chevy G20 was a passenger van powered by a 4.3 liter V6 engine, which can generate up to 165 horsepower.
1,037 Questions
How much for a rebuilt V8 engine for a 1990 full size van?
There are many businesses that offer this service. Check the yellow pages or do a google search for engine rebuilders in your area.
20 inch wheels bouncing on front end of 1998 silverado?
The most common problem with whacky wheels is that they are not mounted and balanced properly...go to a tire shop and get them balanced them mount them
Why does the front end of a Chevy van shake?
That depends on when it shakes.
Low speed, it could be a bad tire, bent wheel...
High speed, it could be a bad tire, bent wheel, out of balance wheel, worn ball joints, worn tie rod ends, worn idler arm...
How do you replace the heater core in a 1987 Chevy G20 van?
This is a very involved process that I couldn't come close to helping you online. Go to your local library and and get a service manual. It will give all the detail and pictures to help walk you through it. Heater cores are not that hard to change but on a van it gets more involved.
What is the weight of a Chevy 1988 G20?
depends on acutal van..there all differant..should be printed in door jam..4500-5500lbs
What is the weight of a Chevy G20 van 1988?
Check on the door sticker to get the correct weight. Matters if your a cargo passanger or conversion van. Weight is all different
The G20 meet once a year in places predetermined. The last few summits have been Toronto, London and Pittsburgh
What is the firing order for a 1976 Chevy 350?
1-8-4-3-6-5-7-2 look on the intake maniflod 2 c where #1 is then the cylinders are from the front 1-3-5-7 on one side then 2-4-6-8 from the front on the other.& mske sure the timing marks are 2gether-(0) & #1 intake & exhaust valves are in the closed position b 4 u set the Timing. NOTE: The # 1 cylinder is the driver side, front cylinder.
The easiest way to do it- both get at the front end for the timing kit and the rear seal is unfortunately to remove grill and radiator- unbolt tranny and engine and kind of slide it forward
Where is the fuel pump reset switch located on a 1991 Lincoln Town car 4.6 Liter?
it is in the trunk on the driver side by the hinge
Where is the wiring harness to hook up trailer lights on a 1990 Chevy G20?
Auto parts stores can sell you a trailer harness that plugs in between your existing truck harness. The electrical connection used is usually located behind the rear bumper on the inside of the left frame. Directions will come with the trailer harness kit.
Little to none. My grandfather bought an '83 new with those same specs except he had 3.08 rear end and he was told not to tow at all! ever! The problem is the transmission. it is just not tough enough. I have the van now and have upgraded it to a turbo 6.5 engine. Transmission only lasts 2 years at the most with no towing. So I upgraded the transmission to a 4L80E. Then the rear end started going out on a regular basis. So I put in a 14 bolt from a 79 van. Nothing breaks now. :):)
I say enjoy the mileage but get something else to tow with unless you love turning wrenches.
What is gas mileage for 1994 Chevy full size van?
I get around 17 mpg with my g20 with the 350 motor \3.42 rearend
What overdrive transmission does a 1992 Chevrolet C3500 have?
The overdrive transmission that a 1992 Chevrolet C3500 would have is a 4L80E. It is a series of automatic transmissions from General Motors.
1990 Chevy G20 parking brake indicator light stuck on?
Check the switch and/or make sure the parking brake pedal is all the way up if it is not that might be air in your brake lines or leak
Where is the oil pressure switch on a Chevy g 20 van located?
On a 5.7 V8 engine, the oil pressure sending unit is on the back of the engine block next to the distributor.
SOMETIMES you can get the window to work one time by jaring the motor by hitting the inside of the door with your hand pretty hard about 6 inches from the bottom and toward the center of the door. This may make it work one time.
I was able to close my window by helping lift the window with my hand while intermittently activating the switch. If this works a little then stops before the window is all the way up, wait a few minutes to let the window motor cool then try again.
Cut a piece of wood approximet 16 inches long about 3/4 inches square take the three screws out holding the motor in then reach in and shove the window all the way up jam the piece of wood on the bottom or the window track and slide the bottom into the door frame and tighten the wood along the framing until it gets tight thanks Wayne
How do you remove the window handle on a 1990 Corsica?
There is a little U shaped spring clip between the handle and the door panel that you need to pop off. You can usually remove it with a screwdriver. Its hard to see but its there. Just slide the screwdriver between the handle and the panel. It may take several tries but eventually you will get it and the clip will come off and then you can slide the handle off. You may want to try to watch though because sometimes the clips fly off and you can't find them. Good luck
How do you change a temperature sensor on a Chevy 1995 G20 van?
slim near the thermostat housing with two wires on it
