Chevy Impala

You are only increasing the tread width on your vehicle about 1/8 to 1/4 of an inch. the same goes for the height. The P235 is the metric width of your tire, and the 60 is the percentage of height to width of the tire. R means Radial and 16 means you have 16' rims or wheels. If the price is right, you will not notice any difference in the driving or handling of the vehicle.

Have you figured out the answer yet? I'm having the same problem.

Jeffrey Wright did you try to cut that security feature off? you can access it through your radio.

If there is, it will be listed in your owner's manual. Depress the push button on the light panel 4 times.

The Chevy Impala LTZ's standard features include the On Star remote ignition block, anti-lock out, anti-theft alarm and pass key, tracking notification and child safety door locks to name a few.

With the engine cold, remove the cap on the power steering pump. Inside the cap is a dipstick with a marking for both the cold and hot fluid levels

If the headlight assembly is the same as a 2003, there is only one alignment screw and it moves the assembly left and right, not up and down.

10W30 unless it gets cold where you live, then change to 5W30 for the colder seasons.

Dexron lll

All of the late Chevy small blocks have a firing order of 1-8-4-3-6-5-7-2. The rotor in the distributor as you look down upon it turns clockwise.

I believe there are 2 adjustments 1 up in the center console by the handle and 1 under the car where the cables split off to each wheel.If you've got drum brakes in the back I'd start by adjusting them though. That's usually how I know it's getting time to do it is by how high the e-brake handle comes up.

The switch comes as a cluster. If you REALLY KNOW what you are doing, this cluster can be taken apart and cleaned with non-conductive cleaner. I took this way out when I learned that the cluster cost was over $150 where the switch is on the arm rest there should be two torque screws holding the panel that the switch is in. Remove the two screws, take out the panel with the switch then gently spread the plastic clips from the panel away from the switch. Carefull not to break the plastic tabs. then disconnect the wiring harness from the switch and install the new switch. follow backwards to reinstall.

I got my 1999 LS into the upper 120's a few times

how do you replace a side mirror on a 2003 Chevy impala?

their should be one screw holding a plastic molding on the side door.

unscrew that and their should be three more screws holding the mirror onto the door.

after those three go, the mirror should just come right off after unclipping the cables hooked on to it

pretty simple i did it on my 2000 impala

transmission fluid. clutch? could be other issues. how do you know it's the transmission giving out? what clues you in?

When the engine overheats because thermostat won't open to allow the water to flow and cool!

reach behind the alternator and down. there is a cap on the resivior. get a long funnel and pour a little at a time and keep checking. although I know that year had problems with their powersteering systems.

Between the Engine Air Cleaner/Filter Housing and the Air Inlet Tube of the throttle Body.....

Disconnect the red terminal on battery and let it sit for 15-30 minutes, reconnect the battery and check engine light should be off because the computer has been reset.

no.

Yes, you must first buy a wiring harness but be sure to know if your factory stereo comes with an onstar system or not. You can find these harnesses by going to crutchfield.com ..if you don't buy the harness there you can at least get the name of the harness and start searching the web....good luck.

You have to replace the instrument cluster in most cases.

Replace the pump before the serpentine belt and rack and pinion are damaged.

The oil pump is the the sump.

they make a tool for it that you should be able to buy at any parts store, i was able to use a pair of needle-nose pliers, open the pliers and put the tips into the notches on the inside of the caliper piston, turning clockwise will compress the piston.