0
Chevy Impala
Launched in 1958, Chevy Impala is a full-size vehicle built by General Motor’s Chevrolet division. It is Chevrolet’s most expensive vehicle and US best selling automobile through 1965. It is distinguished by its triple symmetrical taillights.
4,997 Questions
What is the maximum cargo capacity of the 2008 Chevrolet Impala?
The maximum cargo capacity of the 2008 Chevrolet Impala is 18.6 cu.ft..
What kind of fuel does the 2009 Chevrolet Impala use?
The 2009 Chevrolet Impala runs on flex-fuel (FFV).
Why do 2000 impala power door locks not open whne putting transmission in park?
See {Programmable Automatic Power Door Locks} on page 2-5 of your "Owner's Manual" for info and then {Autolock} on page 2-16 for programming....
1964 drive shaft removal Chevy Impala?
Mark driveshaft and yoke to insure re-installing in the same location to maintain factory balance remove and discard small "U" bolts at differntial yoke pry driveshaft out of yoke and up onto transmission splines lower driveshaft to ground and slide off of transmission splines use new small "U" bolts upon installation
How do you flush the radiator on a 2001 Chevrolet Impala?
i just flushed my radiator on my 2001 impala
if your car hasn't hasn't been flushed in a while, i recommend adding a radiator cleaner and driving a day or 2 to help break-up gunk..
1. remove plastic protector under radiator and fans (5 screws)
2. carefully unscrew butterfly screw under the radiator( very hard to find on this vehicle but it's on the driver side) ( use an adjustable wrench because screw is very tight from factory!)
3. let all coolant drain
4. add new anti-freeze at a 50% to 70% coolant-water ratio depending on average temp in your area.
5. start car with heater on to remove any air from radiator
Flush1. Park the vehicle on a level surface with engine switched off and heater switch turned to on position. Cover the engine to protect it from splashes.2. Take off the radiator cap. Turn tap at bottom of radiator to let water out and disconnect upper and lower radiator hoses.
3. Inspect the condition of the hoses. If they are brittle or soggy replace them with new ones.
4. Inspect the old liquid that comes out of the radiator. If it is clean, that's good. If it's dirty, especially if it's brown with rust, the system needs an extra special flushing. Whatever happens flush the system anyway.
5. Put the water hose into the top of the radiator and let it gently flush through for a while, hopefully until the water runs clean again.
6. Put the hose in the bottom radiator outlet and reverse flush. Then flush from the top again .
7. Flush through the engine cooling jacket to remove any deposits.
8. With a very dirty radiator use a can of radiator flush. This involves putting the hoses back on, topping up with water again, inserting the flush treatment and running the engine for a while to loosen corrosion deposits. Then you empty the radiator again and flush again with a water hose, as previously described.
9. When flushing is completed, close radiator tap, refit hoses and fill radiator with 50/50 mix of the proper coolant and distilled water.
10. Before replacing the radiator cap, check its condition. If it is old or rusted, put a new one on.
11. Bleed the system to remove any trapped air.
How do you replace the thermostat located on a 2001 Chevy Impala?
You have to remove the air filter unit. Take the flexhose off and then you have to remove the breather. That's the only way to get at the bolts. Its a real painbut its the only way. I just did mine. Good Luck!!!
On a 3.8L V6, it is very simple. Follow the upper radiator hose to the manifold just in frontof the throttle body. Loosen the hose clamp, pull the hose off of the "gooseneck". Loosenthe 2 10mm bolts (deep 6 point socket works best). And off it comes! Clean the surfacesand re-install new one.
It also helps to disconnect the 5-6 local sensors so that you can pull the wiring harness out of the way. There is also a vacumm line that you can pull off to help with clearance. Be gentle with the vacumm lines as they become brittle with age and heat over time.
$8-$16 for a new themostat and gasket.
It means the engine didn't warm up to the correct operating temperature. Thermostat is probably stuck open. Replace the thermostat.
Where does the power steering fluid go on a 2000 Chevy Impala?
Power steering pump reservoir. Back of engine passenger side.
What is the timing for a 1967 Chevy impala sports coupe?
4 degrees btc-before top dead center with the vacuum spark line disconnected.the timing mark location is on the harmonic balancer. this is for a 327 engine
How do you release fuel pressure on 2001 impala?
there should be a valve on the fuel rail on the engine that you release the pressure, it looks just like a tire valve.
How do you reset the clock on a 2000 Chevrolet impala?
Your owners manual will have all the info you need to do that.
How do you reset the monitor to turn off low tire warning light for Chevy Impala 2000?
ANSWER (ONE THAT REALLY WORKS)
Turn the key to the "ON" position.
NEXT
Find your head light switch (Knob)
NEXT
Pull it "ONE" click out and push it back in. Do it three times.
You then hear a little DING, DING, DING sound and the switch is resetted. NO MORE WARNING LIGHT DISPLAYED. You well come!!!!
P.S: When pulling the light switch be sure to pull it out just one click to the parking light mode. If you pull it out two clicks to the headlight mode the system will not reset.
P.P.S. If you want to reset your CHANGE OIL WARNING LIGHT turn key to on position, not start. Then press the gas pedal down 3 times.
AWFULLY COCKY FOR SOMEONE WHO CAN'T SPELL WELCOME
the best way to do this is to consult your owners manual that come with the car and follow the instructions within.
How do you remove the side door paneling to replace power window motor in impala 2001?
remove the screw in the inside handle then pop out the plastic piece and remove the screw inside there (big torx bit) remove any other visible screws and pop off the panels retainer clips, disconnect the power lock and window wires.
How do you remove the PCV valve on a 2001 Chevy Impala?
there are 2 wires coming in front of engine wear the drive belt is on the top of the engine push down on them and turn like you was changing a light bulb its under there
Will 26 inch rims fit on a 2007 Crown Victoria without rubbing?
go to www.kingofthestreet.com and see their message board in the suspension section.
Where is the headlamp fuse located on a 2005 impala?
See Fuses and Circuit Breakers, under Section 5: Service and Appearance Care - Electrical System on page 5-95 of your "Owner's Manual".....
What is the best course of action if a power steering pump is leaking?
It is cheaper and best to replace the pump with a remanufactured one.
How to change Brakes on a 2000 impala?
1. Take wheels off. (3/4" socket)
2. Use 14mm socket to remove bolts from the caliper.
3. Use a C-clamp to tension the caliper.
4. Put new brake pads in.
5. Put the caliper in position and retighten the 14mm bolts.
6. Put wheels back on.
7. Get in the car and pump the brakes at least 5 times to re-juice the calipers.
What is the price for a 68 Impala convertible?
The price of a car depends on its condition, and mileage. A well taken care of 1968 Chevy Impala convertible price can be between $15,000-$28,000.
Where do you add power steering fluid on 2000 grand am?
On the four cylinder model the power steering pump is located at the opposite end of the engine and is driven by the camshaft. there should be a reservoir and a cap.
What is the firing order for a Chevy 400?
1-8-4-3-6-5-7-2 clockwise on cap.
Driver's side head front to back is 1-3-5-7 cylinders.
The other head .........................is 2-4-6-8 cylinders.
Why would new wipers squeak when it rains but not when the windshield is dry?
my first quess is that when the glass is dry, the friction caused by the dry glass and the blade actually slows the blade down enough so that it doesn't skip, skip, skip. kinda like bouncing from one spot to another. when your windshield is wet; however, the friction is less and the wiper motor makes the blade move faster. if the tension on the blade is too high, the blade will stick, release, stick, release, etc. thus causing a "Squeak" or sputter. May want to try loosening up the tension spring just a hair, then spray your sheld with the hose and try it until the blades work just right. You may also just need new blades. should be about $40 for a good complete set.
