0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
How do you remove fuel pump on a 1999 Chrysler Concorde?
the fuel pump is in the gas tank. the tank has to be removed.
How do you know when a manifold tuning valve is bad?
You can tell when a manifold tuning valve is bad when oil is leaking through it. You also can tell by inserting the dipstick into the valve and seeing if oil comes out through the dipstick.
How do I fix 2000 Chrysler Concorde stuck electric windows in front seats?
if the switch works then the widow motor need to be replaced take the door panel off and see if something is effecting the travel of the window if the motor works
How much does it cost to replace the suspension?
If you mean the air ride system, could cost more then what the car is worth. Depends where you get the parts. Check out " strutmasters.com" They will have what you need.
Where is the transaxle reset on Chrysler Concorde?
Chrysler does not have reset switches. You need to check for trouble codes with a scan tool.
Chrysler does not have reset switches. You need to check for trouble codes with a scan tool.
How Replace Rear Window Brake Light on 2000 Chrysler Concorde?
In the top of the trunk near where the brake light is located, there is a small plastic window, remove it and you access the light bulb.
How do you change the water pump on a 97 Concorde with the timing belt in the way?
Sorry to tell you this, timing belt removal is a must before removing the water pump. If the belt has around 60,000 to 100,000 miles, it needs to be replace anyway and might as well do it since it's right there in front of you. At a garage, probably cost you $500.00 and up.
How do you take off the passenger side door panel on a 99 Concorde lxi?
Scan the entire door panel for screw locations, lift panel up after screw removal, unplug auto lock and auto window plugs than undo clip on rod for door handle. Very simple process though you may run into a black tar like substance which is there to hold the plastic barrier.
Good Luck :)
Tom
How do you replace a 2002 Concorde wiper motor?
It's different on different Chrysler models, but check for access from outside the vehicle, by removing the air intake grill below the windshield.
The bottom screws on the air intake grill simply unscrew, but they screw into plastic inserts that are probably stripped out. You fiddle with them to get them out.
The top screws on the air intake grill do not unscrew. They're actually a latch arm that rotates about 1/4 turn to release.
To remove the windshild motor, you have to rotate the motor/arms assembly to the right position by trial and error.
BE EXTREMELY CAREFUL AND PROTECT THE WINDSHIELD. Windshield replacement is some serious bucks.
What are the torque specs for the intake bolts on a 97 Chrysler Concorde?
17 foot pounds on a 3.3 Liter, and 21 ft pounds on a 3.5 Liter
How do you replace a fuel pump on a 1996 Chrysler Concorde?
I just replaced my fuel pump on a 1996 Chrysler Concorde. I'm no mechanic but it wasn't that difficult.
If you know the fuel pump is the issue and it will definitely need to be replaced, I suggest having the part available because there are instructions for safety in the packaging of the part that I was not aware of when I removed my original Fuel Pump Assembly (FPA).
Here's how I did it:
Clean out the trunk. I did all of my work through the trunk. Did not have to remove the seats from back of car. Pull back the carpeting in trunk but you should not have to remove it.
In the back of the trunk remove 4 nuts. Remove plate. I suggest keeping removed items away from your working space because you will not want to drop anything either down the exposed opening or in the gas tank after the FPA is removed.
Next, disconnect three hoses/tubes from top of the FPA. NOTE: One of these hoses (the smallest) attaches to a cylindrical device called a rollover valve. Take note of the orientation of this device, first because you will have to remove and reuse this part (it is not included in the replacement FPA) and also because you could become confused on which way it needs to go back in. Keep in mind that as you pull these tubes off that a small amount of gasoline is likely to spill.
Also disconnect the electrical fitting by just pulling it out.
The two larger tubes mentioned above have a snap-in assembly in the inner diameter of the bell shaped end of the tubes that you will also need to reuse. I used a small screw driver to delicately defeat the snaps so that I could pull the tubes off. They are each a different size so you're not likely to confuse them.
Now you are ready to remove the FPA by loosening the S/S band that goes around the top perimeter of the FPA. This was a challenging task but to get it out I managed to do it with a short screw driver as this is a tight space. When I put the band back on during the reinstallation of the FPA at the end of my project I was wise enough to have already purchased a small ratchet set which was almost a necessity as I look back. I got it at a local hardware store for $9 and it was worth buying for just this one project.
When the band is loosened the pump is ready to come out. A few notes: The FPA pump has attached to it what I assume is a float device for fuel level indication. This may impede to a small extent the removal of the FPA but with a little tilting and lifting it will come out easily. Again keep in mind this unit will have a decent amount of gas in it, some of which will likely spill.
Remember that the rollover valve is in your removed FPA and will have to be transfered to the replacement FPA. I could not get mine off of the old unit by pulling. It fits down through a rubber grommet and should simply pull straight out of the opening in theory, but mine would not so I got a hack saw and carefully cut it out of the removed FPA.
I was able to push the reused rollover valve into the new FPA but I did use a soapy lubricant to get it to go easily. Obviously, wipe off any lubricant that you use for this before placing the FPA unit back into the fuel tank.
Where is the cam sensor on a 2000 Chrysler Concorde?
It is mounted on the front of the engine slightly to the right as you look from the front. There is a clip attached to it. 1 Bolt holds it in.
How do you find the problem if your Chrysler Sebring's 20v ignition fuse keeps blowing out?
I had the same problem. Everytime I would turn the ignition past Accesory to the On position the 20A fuse would pop. I went through 15 or so fuses. I could get it to start every now and then, so one time it started I drove it up to Sears Auto and they diagnosed the Battery as having a bad cell. Replaced the battery and haven't pop a fuse since then.
Popping the 20A ignition fuse....have your battery tested and probably replaced!
check the starter too if battery is good
I had this problem as well. It turned out to be the starter. It occurs when you move to "start" and the starter fails to engage. Whether this was simply a bad solenoid, or something else in the starter, I can't say for sure. In short, if the engine didn't immediately turn, the fuse would blow in about 2 seconds. I got around it for quite a while by being very careful to not hold the switch in start unless I detected the engine turning over. Eventually the starter ws relaced and all is well.
Where is the crank sensor on a 3.3 1995 Chrysler Concorde?
Passenger side of engine block about half way down. That's where it was on my 94 Concorde.
How do you replace cv axels on 97 concord?
remove tire, remove brake callipar, remove hub bearing bolts (3). remoce drive axle nut 1-5/16 remove lower control arm, pop out drive axle.
How do you replace the starter on a 98 Chrysler concord?
Disconnect the - battery cable
Raise and support vehicle
Remove wiring harness at starter
Remove mounting bolts
Remove starter Disconnect the - battery cable
Raise and support vehicle
Remove wiring harness at starter
Remove mounting bolts
Remove starter
Why does a 1999 Chrysler Concorde misfire?
The Concorde could misfire for several reasons. Start by checking for proper fire to the spark plugs. Then check engine compression to see if a cylinder compression is down.
How you replace battery in Concord 2002?
jack up paasenger side of vehicle remover tire then remove wheel well disconnect negative cable, positive cable, battery holddown and remove battery installation is reverseal of uninstall
Where is the amplifier at for a 2000 Chrysler Concorde lxi?
if you have an factory infinity system they usually have a small inline amp at each speaker. not built into the factory deck. you have to remove or wire arround each amp before you install an aftermarket deck. or you'll just get humming and static. In the trunk on the driver side wall,under the carpet.
How do you replace the water pump on a 1997 Chrysler 3.5L motor?
you have to take the timing belt off to do the water pump.and you also have to do the rear timing cover where the water pump is attach to because theres 3 o ring gasket behind that cover and they are known to leak.
Where is the Cam Position Sensor located on a 3.5 2004 Chrysler Concorde?
Top front near center of engine,a bit on the driver's side, partly under the
intake manifold. only sensor in the area(wires connected to it)
It CAN be removed and replaced without removing intake manifold.
(a little filing and a little forcing)
