0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
What would cause a 1998 Chrysler Concorde to run hot?
It could be one of many things.......radiator fans notworking/low on coolant/stuck thermostat/ radiator may need to be flushed......
Where is the Location of thermostat in a 2000 concord 3.2 engine?
the thermostat is located at the bottom of the drivers side engine under exhaust manifold next to the oil filter
Will replacing your blower motor solve your problem it only works on high?
No,
You will need to replace Blower resistor and it is siting on the blower body.
It is easy fix and cost about $15. If you have any question let me know izoavdic@gmail.com
When installing a thermostat on a 2002 Chrysler Concord which end goes in the block?
The spring goes in the block.
The spring goes in the block.
How do you change a brake light on a 2000 Chrysler Concorde?
The Left and Right are very easy.
There are 3 1" diameter plastic spinner nuts on each side in the trunk, very visible and accessible Remove these nuts. and entire light assembly will then be free from the rear body panel ...pull toward rear. This exposes all the lamps. The lamp holders are 1/4 turn to release and the old lamps can be pulled out and replaced, note polarity. The center lamp requires you to remove the trunk liner under the back shelf. pry loose the 4 plastic "pine trees" this will expose the lamp holder . It takes two lamps for the center.
Where is the starter on a Lumina?
It is located at the front,you actually can look at it when you open the hood.I would say the middle left.
How do you change a 1997 Chrysler Concorde air filter?
Open air filter box on left side facing front of car and pull old retangular one out and drop new in. Re-snap hosing cover. Job done.
What will happen in the sky 17th october 2010?
- Nope ....Nothing Happens On That Day !
- Those People Who Have No Work Spread This Rumors And Try To Fool Others.
- So People Dont Believe In Such Rumors Until You See It With Your Eyes!
Smell coming from vents 2000 Chrysler concord?
If it smells musty check the evaporator drain hose hose.
Johnny Texas.
What is the highest speed of the concord?
Mach 2.2 (~1,450 mph, 2,330 km/h) it is limited by strength material used to make skin (aluminum).
How do you replace the rear speakers in a Chrysler Concorde?
There are two bolts at the bottom of the back seat by the floor.......then you remove seat and take out the two bolts for the upper back seat and then you remove the back dash to get to the speakers! hope this helps
How do you change map light in 2005 Town and Country?
To change the map light in a 2005 Town and Country, first lower the sunglass holder. Remove the single screw holding the console and firmly pull down the entire console from the rear. It will release the two clips allowing the entire console to be removed and the map light can be changed.
1995 Chrysler Concorde and it keeps blowing the same fuse what is the problem?
Fuses That "Blow" Repeatedly
Without being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.
The following generic answer applies to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].
Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors. And in a worst case, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.
When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.
The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.
The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].
Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
Why does the trunk lid open on its own?
could be a short in the electronic release on your trunk latch. if you have one of those handy lil remotes that opens your trunk for you, that meaans theres a little electronic switch that's hooked to your latch. if there is a short " 1 or 2 wires toucing each other or something metal in your car" that could be a problem. does it happen when you go over bumps ? or another reason is that your latch could be adjusted to loose and needs to be tightened, the loop lowered ect. could be many things with all of the electronics in cars today. it is either mechanical, " whole trunk lock assmbly is to loose" or electronic " the electric switch hooked to your latch, or maybe a short in the remote that keeps popping when not wanted. those are a couple options to think about.
How to get the wiper arms off on a 96 concord?
To remove the wiper arms from a 1996 Concord, remove the small clip holding them on. Then pull up on the arm.
How do you reset the air bag light on a 2002 Chrysler Concorde?
The airbag light stays on when the computer has detected a malfunction and set a trouble code. The light can not be reset until the failure has been repaired.
Try contacting the dealer they maybe able to use your VIN# and get you a new remote.
Try unlocking the doors and trunk with the key.
Why might a Chrysler Concorde not start?
my Concorde wouldn't start and we took it in and had the starter replaced it was 420 dollar but the car runs now
my Concorde wouldn't start and we took it in and had the starter replaced it was 420 dollar but the car runs now
Why did the brakes stop working on a 1995 Chrysler Concorde?
I would suspect a defective Master Cylinder.
Fluid leak.
How do you get the locking mechanism open in order to close your car door?
first open door or if its already open, pull inside door handle while prying up on the actual locking mechanism it should move up into where it should br
How do you remove the rear struts on a 2004 Chrysler Concorde?
I just removed the rear struts on my 2004 Chrysler Concorde. To remove the arm you will need to use a little force. You will notice first a hose with a join in the middle where the arm meets the cowel of the car (the plastic vent shaped piece right by the base of the wind shield). This hose is how the windshield solution is delivered to the wiper arm. You want to pull this hose apart right at the join, it should come apart.
Now you need to remove the arm itself. There is a metal mushroom shaped piece that comes out of the car, the wiper arm slips over the head of this mushroom. The metal tab which is attached to the wiper arm (that slipped on) simply slides under the bottom of the mushroom head to keep it from coming off. You need to pull this tab out to remove the arm from the mushroom head. This tab is not always easy to move.
I used a screw driver to gently pry the tab downward (toward the cowl) so it would come loose. Once loose I slid the tab out (it doesn't come out completely, just partially) until I saw a small hole in the tab piece. Then I pried the arm off the mushroom head using a fulcrum and a lever combined with a gentle twisting and pulling motion. It came off this way.
