0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
Where is thermostat located on 2002 Concorde 3.5L engine?
Find the upper radiator hose and follow it to the engine. Normally it will be located somewhere where this hose meets the engine in a housing.
What if your 2000 Chrysler Concorde transmission will not shift from lowest gear?
Have the trans computer checked for trouble codes. That will give you a place to start diagnosing.
42LE transmission Service change only - 4.5 quarts. Total refill - 9.9 quarts.
Are you sure is isn't overheating. The sealed cooling system can develop small leaks and you can lose most of your coolant. When this happens the car overheats and will run rough and die. When it cools off it will run again. Could also be ignition module or some other electronic compnoenet. Are there any codes?
Were is the factory alarm located in a 1998 Chrysler Concorde?
The factory alarm is part of the body and engine computers.
How do you replace the water pump on a 1995 Chrysler Concorde 3.5L?
the water pump is driven by the timing belt, so the front of the engine must come off, including radiator, fans, belts, pulleys, timing belt cover, etc. the timing belt removed (making sure cams do not rotate, water pump can then be changed. 4 bolts i think. its just a pain to get to it, then when you put the belt back on, you must put the belt tensioner back on correctly. best way is to remove it, compress it in a vise then insert the proper pin to hold the spring back while you bolt it back on. the spring is very strong and will bend bailing wire or mechanics wire, so do not use that. use the proper pin...call the dealer or parts dealer for info on this. A cheapy chiltons manual explains it fairly well if your a decent mechanic. if your not comfortable doing all this, take it to a shop that is.
Why is the supersonic transport named Concorde?
Concorde is French for 'agreement', and this was chosen to signify the agreement and co-operation between Britain and France in developing the plane.
The alliance between the French and British led to Concorde's construction. The name Concorde is from the French word Concorde, which is the English equivalent of Concord. It means agreement or union. It was at first referred to by UK as Concorde with the French spelling but was changed to Concord by Macmillan.
They named it that because of a treaty! How cool!
Concorde's name reflects the development agreement between the United Kingdom and France. In the UK, any or all of the type-unusual for an aircraft-are known simply as "Concorde", without an article. The aircraft is regarded by many people as an aviation icon and an engineering marvel.
Thats why it was named the Concorde.
They were allies in world war 2.
The Concorde is a really fast jet.
Concorde is called Concorde because when Britain and France were thinking of a name a civil servent's family thought of it.it means "agreement between persons, groups, nations,and harmony, goodwill,and friendship.At first it was spelt concord by the british,but the french wanted to call it Concorde.There was a bit of an argument and in the end it was Concorde.
Because there is too much detail to properly give instructions. A manual costs about eleven dollars and is more specific to your vehicle and has all the details plus pictures, plus you will have it handy for any other future repairs. If you can't afford a manual, I recommend checking your local library to see if there is one available for checkout.
Is it bad to run the ac with the engine turned off?
no but it can cause motor to lock up because no air flow
How do you reset the check engine light 1994 Chrysler Concorde?
After fixing the cause of the problem. you clear code with a scan tool, or by unhooking the battery.
What is the Oil capacity Chrysler Concorde 3.5?
The oil capacity of a 93-97 Chrysler Concorde with a 3.5 liter engine is 5.5 quarts.
I have a 3.2L that had the same problem. There's a hard antifreeze line that runs down the back of the motor(along fire wall) that had a break(rusted) on one of the bends. It only pissed when the car warmed up and you have to remove hoses and clamps and reservoirs to get your hands in it. I had to cut it from underneath and above and replaced the rusted hard line with a soft flex hose. Good luck, once you get going, it's not that hard.
How do you change dome map lights in a chrysler concorde 2000?
light bulb out on map light how to change with out breaking plastic lens
Will a 1995 Concorde 3.5 engine be used to replace a 3.2 engine in a 1998 Concorde?
No, will not work. why not?
Is clicking noise in a Chrysler 3.2L engine normal?
I have the same car with the same clicking noise right after you start the engine. The noise stops shortly after starting. There was a recall from Chrysler for this problem. Contact your local dealer regarding this matter.
Should the Concorde engine be running when checking trans fluid?
yes, the engine should be running and warm when checking the trans fluid. careful where you put your fingers and don't get burnt on the exhaust shield. The dipstick ios located on the right hand side of a 3.5 L nice and tight like everything else under the hood!
Where is the O2 sensor located in 98 Chrysler Concorde?
There are 4, one before and one after each catalytic converter in the exhaust.
04 Concorde front left wheel squeaks when turning braking and accelerating from stop?
I just had this problem and it was because I changed the brakes and the new rotors where touching the lower ball joint heat shield. I just had to take a screw driver and bend the metal heat shield just a little and the squeal went away
Where is the thermostat located on a 1999 Chrysler Concorde?
It is under the housing where the lower radiator hose attaches to the engine.
Is it easy to manually change out a 1994 Chevy Lumina water pump and if so how is it done?
Fairly easy. remove the serpentine belt. Remove the pulley from the water pump. You need the sockets that fit those bolts and the sockets that fit the pump's mounting bolts. Get gasket sealer too.
How do you change spark plugs on a 2000 Chrysler Concorde?
Looking at the top of the engine. Look between the runners of the intake manifold and you will see six square black boxes all held on by two star head screws. Remove the screws and pull up the coil boxes, under these are your plugs. Use a deep socket to change the plugs.
How do you replace the battery in a 1999 Chrysler Concorde?
== ==
== == == == The procedure for removal and replacement is basically the same for all autos, not just your Concord, so this procedure is generic in nature. The battery has two TERMINAL POSTS, one of which is electrically positive ["hot"], and is usually identified on the battery top with a "+" symbol, and/or the abbreviaton "POS." The other terminal is electrically negative ["ground"] and is identified on the battery top with a "-" symbol, and/or the abbreviation "NEG." To help prevent placing the wrong cable on the terminal of opposite polarity, the posts, and cable clamps are different sizes [diameters], with the positive terminal being slightly larger than the negative. Usually, but not always, the battery cables are identified by the insulation on the positive cable being RED, and the negative cable insulation being BLACK. If, in placing a clamp to a post, you notice that the clamp either is too small to fit the terminal, or too large and loose to fit, THEN you are trying to put the cable/clamp on the WRONG terminal post! Pay very close attention to prevent a REVERSE polarity connection, as this can DESTROY many EXPENSIVE ELECTRONIC COMPONENTS in your vehicle. Both the negative and positive cables are terminated, on their battery ends, with a "split" clamp which encricles the round terminal posts. The clamps are secured to the terminal with a cross bolt which tightens the clamp to the post. A wrench is needed to tighten or loosen the bolt. FOR SAFETY, anytime you are working on or near electrically energized wires or components, ALWAYS DISCONNECT the negative cable from the negative terminal BEFORE doing anything else. It is IMPORTANT that the NEGATIVE [GROUND] cable is removed FIRST because IF the metal wrench should contact between the negative terminal and a grounded metal body component, NOTHING WILL HAPPEN. On the other hand, IF a metal wrench contacts both the positive terminal and grounded metal, WHILE THE NEGATIVE GROUND cable is still connected, a monsterous SHORT CIRCUIT will result, throwing arc sparks everywhere, possibly causing the wrench to overheat, burning your hand, and in the worst case, COULD cause the battery to EXPLODE, spraying shrapnel and SULPHURIC ACID EVERYWHERE !!!!! ALWAYS COMPLETELY DISCONNECT THE NEGATIVE CABLE FIRST ! Once the negative and positive battery cables have been removed, the battery retaining mechanism [there are several different types] must be removed. Some are a bracket which clamps over the top of the battery, while most newer vehicles have a triangular "bar" which mates with a slot in the bottom edge of the battery case. This secures the battery in the tray, and prevents the battery from "bouncing" out. Once the two cables and the retainer have been removed, the battery can be lifted out of the vehicle. Batteries are very heavy relative to their physical size, so be sure to have good footing, good balance, and use safe lifting procedures to prevent physical injury. Installation of the new/replacement battery is simply a matter of reversing the above procedure. Good luck. j3h
Where is the blower motor resistor on a 1999 Chrysler Town and Country?
Under the hood, on the firewall, over the top of the passenger side strut tower. Look for a plastic plug with about 5 connections. To remove:
1) Disconnect the negative battery terminal (suggested in svc manuals.)
2) Unplug wiring harness (release tab is on top of plug.)
3) Depress the spring fasteners on sides of unit (this is difficult; they are behind the base; look at the replacement unit for reference.)
4) Rotate unit clockwise (pull left side out first) as it comes out in order to clear the rigid A/C lines.
