0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Where is the crankshaft position sensor located on a 1996 Dodge Ram 2500 with the 318 engine?
the crankshaft position sensor is located in between engine and trans passenger side. it easy to change .
It is in the top of the bell housing on the pass side, under the trans dipstick tube.
Where can you find a vacuum hose diagram for a 1980 Mustang with carburated California 2.3 liter?
i got a mustang repair manual off advance auto parts online for 79-93 mustangs, has an ok diagram. book costs $27.99
What kind of mileage should a dodge ram 2500 get with the diesel 6?
With a load (3500 lb camper), I get 14-17 MPG, with no load I get 19-21 mpg. 2001 Dodge Ram 2500, HO diesel, Manual Transmission
How do you troubleshoot the 1996 Corvette PKE system?
I'm having issues with mine as well. One day me locks started to cycle erratically and my hatch popped open. Now there is no response whatsoever and it will not even enter the programming mode. My research has concluded that the PKE computer has gone bad. It is located under the top dash pad. Now I have to buy it for $250 and figure out how to remove the pad. Hope this is of some help.
How does multiple displacement system on 5.7L V8 SFI Hemi Engine work?
If the Mopar system works the way others I am aware of work, it's actually quite simple. The engine computer senses when the vehicle is under a light load situation, such as steady speed highway driving, and it shuts off fuel and spark to as many as 4 cylinders. Then engine only uses the remaining cylinders to make power, using less fuel to do so. When it senses a need for more power, it will turn these cylinders 'on' again to tap the available power that the engine is capable of making. This process effectively cuts the displacement of the engine from it's full 5.7L to as little as 2.85L depending on how many cylinders it cuts out.
Through the use of solenoids and oil pressurte it also "shuts off" the lifter to those 4 cylinders
How do you remove front brake rotors on a 1999 dodge ram 2500?
You have to remove the wheel hub assembly, drive the wheel studs out with a hammer, and flip the assembly over to remove the rotor from the back side.
The wheel hub assembly removal requires removing the caliper, 1 11/16 inch nut on the axle shaft, loosening the 4 bolts (14mm 12 point socket) that hold the hub to the knuckle, and hammering on the bolts to loosen the hub. ( use a sacrificial socket to save the bolt heads).
You have to remove the wheel hub assembly, drive the wheel studs out with a hammer, and flip the assembly over to remove the rotor from the back side.
The wheel hub assembly removal requires removing the caliper, 1 11/16 inch nut on the axle shaft, loosening the 4 bolts (14mm 12 point socket) that hold the hub to the knuckle, and hammering on the bolts to loosen the hub. ( use a sacrificial socket to save the bolt heads).
What is code P0463 on a dodge diesel mean?
Fuel level sensor circuit high.
You have an open circuit in the fuel float or in the wiring to the tank.
Is there an equivalant antifreeze to Havoline Extended Life Coolant for a Rover car?
Yes there is. It's Available thru Amsoil and is good for
Up to seven years or 750,000 miles in Class 8 vehicles
Up to seven years or 250,000 miles in pleasure vehicles
Where the Havoline is 5 years.
For info see link.
Hope This Helps.
Where can you find the fuse box of a 1986 mustang 5.0?
Sit in the drivers seat. It's on the bottom of the dash above your left ankle.
Need diagram for carburetor and vacuum hoses for 85 dodge ram pick up D100?
These diagrams can be easy to find. It is best to look through the users manual or to find an image online.
What is the wiring schematic for the ignition on a 1990 Dodge Cummins 1-ton pickup?
A dodge Cummings diesel does not have an ignition system its a DIESEL
REAL ANSWER
Sorry about that poor answer above, obviously does not know what you are referring to (cannot even spell Cummins) I am a mechanic for Cummins. If you need the wiring schematic for your starter, fuel on/off solenoid and ribbon heater as pertaining to the ignition switch in the truck, I'd be happy to supply you with the information. jeebs_9@hotmail.comHow do you change the front and rear sway bars on a 95 windstar lx?
to do the frt one's put a jack under the sub frame and then undo the sway bar links remove the two rear sub frame bolts and let the jack down slowly you may have to unhook the exhaust at the flex pipe remove the four bolts from the sway bar bushings and the bar should come out.
How do you adjust front seat in 1990 vw jetta?
there are controlls located on the right dide of the seat under the front that allows you to move back and fourth, there's a wheel adjuster on the right back side that andusts the back of the seat and under the front lefs adjusts the tilt
Looking for number one on distributor cap for a 1979 dodge 318?
# 1 on the distributor cap faces to the FRONT / CENTER
What is wrong when the power windows blower motor and abs and airbag light is always on?
you have bought a general motors car
Where is the map sensor located on 1988 dodge ram?
on the passenger side firewall. should see a single vacuum hose and a three wire connector going to it.
Where is the crank position sensor on a 1999 Dodge Ram 318?
In through the top of the bell housing. It is behind the trans dipstick tube, behind the passenger head
In through the top of the bell housing. It is behind the trans dipstick tube, behind the passenger head
