0
Dodge Vans
Dodge has been producing panel delivery models for several years since 1914. However, its first purpose-built van model was launched in 1964 – the compact A Series. The carmaker then released the B-Series, followed by the rebadged Ram Van and Ram Wagon.
462 Questions
How many gallons in a 3 point 6 liter engine?
If you mean how many gallons for... displacement... .95 gallons. If you mean the fuel tank, either 22 or 35 gallons, depending on the year / choice
How do you install water pump 3.0 dodge caravan?
I just replaced the water pump on our 2000 3.0 liter. It is NOT a simple job like the 3.3. Not necessarily in this order, you will need to remove:
Passenger front tire
Lower splash shield
A/c compressor drive belt
Serpentine Belt
Idler pulley
Power steering pump
Compressor idler pulley
A/c compressor and mounting bracket
Motor mount (be sure to support motor)
Harmonic balancer and pulley from crankshaft
"front plate" on motor (large 1/4 in thick black metal plate on end of the motor)
Timing belt covers 3 pieces, two half circles over each cam and a large v shaped piece over the block.
Be sure to mark each cam sprocket and the crank sprocket locations on the belt to aid in retiming the engine at reassembly.
relieve the tension on the timing belt, be careful, the camshfts will turn quickly due to valve spring pressure
Remove timing belt.
Waterpump is finally accessible
Remove only the 12 mm bolts on the water pump, the 10 mm hold the two halves together and it is much easier to remove as a whole unit because for some reason, the genius that designed the pump put a Phillips head screw in the backing plate which needs to be removed to separate the two halves of the water pump, but it is not ac accessible until you pull the whole thing. If you remove the 10 mm bolts and try to pull just the water pump out, you will most assuredly crack the backing plate at that screw, don't ask how I know!
Now, just pull the pump out, it is on an 1 1/2 pipe with an internal o ring, so, pull fairly hard on it. The oring was what failed on my van.
1989 Dodge Truck B250 Van V8-318 ignition control module location?
no idea all i can find is people looking for the same answer maybe incorporated into computer
Probably a bad master cylinder...
1997 Dodge van how to replace dash lights?
First, disconnect the negative battery cable. I'm not a big safety nut, but there's a hefty cable from the ammeter that's connected directly to the battery. I made a pretty big mess of my wiring harness when I pulled my instrument cluster and bumped it up against the sheet metal part of the dash.
That being said, remove the four Phillips-head screws from the cluster, slide the cluster as far up the steering column as the cables will allow, and reach behind the speedo and disconnect the cable. There is a small tab on the cable that, when pressed, will release the cable from the speedo head.
Next, gently pull the main harness plug from the center of the cluster. If it's never been off, you'll have to do some wiggling of the plug to get it loose.
Finally, remove the two cables from the aforementioned ammeter. I believe they're held on with 11/32" nuts. Pay attention to where the red and black cables go. Nothing will be harmed if you get them backwards, but your ammeter will read opposite to what's actually happening.
At this point, the entire cluster can be lifted free. You'll find all the lamps held in with 1/4-turn sockets. A quick left-hand twist will free them to be removed, with the blade-style lamp easily pulled from the socket after that.
You may find that you can get to the lamps in question without pulling the cluster out, but it's so easy to remove, and it makes lamp change much easier.
Where is fuel pump in 1973 Dodge 318 in a winnebago motorhome?
if the pump is a electric one than its located by the rear fuel tank, however if its a machanical one than its located under the alternator
Mechanical pump on the front passenger side of the engine.
Where can you buy or fix your dodge conversion van?
depending on what is wrong with it and what type of conversion ist camping or touring
How do you fix the horn 2001 dodge ram?
CHECK # Remove the cover from the power distribution center and check the relay and fuses # Disconnect the electrical connector from the horn # Have an assistant press the horn button and use a voltmeter to make sure there is battery voltage at the dark green/red wire of the connector if the relay is god and theres no voltage at the horn the wire which leads to the relay has a fault # Use a ohmmeter to measure the resistance between the wiring connector black wire and a good ground.There should be zero ohms # If theres voltage at the horn and the wiring circuits are good the horn is faulty REPLACEMENT # Disconnect the electrical connector remove the mounting bolt and detach the horn
Where is the throttle position sensor on a 2005 4.7L dodge durango?
It is located on the throttle body on the opposite side from the throttle cables.
Error code eleven on 1996 dodge b2500 van?
* 11 No ignition reference signal detected during cranking (bad Hall effect) OR loss of camshaft sensor (and, for cars with crankshaft sensors - which does not include the 2.2/2.5 - timing belt skipped a tooth or loss of crankshaft sensor). See note #8 below.
Can cause the engine to stop working entirely with no limp-home mode. Note: An anonymous poster wrote, "Code 11 will only be set upon clearing the codes, most commonly by disconnecting the battery. It says in the factory diagnostic manuals that code 11 means no ignition reference signal has been seen since battery disconnect. As soon as the vehicle's engine is cranked, and a reference signal is seen, code 11 will go away immediately on it's own. It also won't be set upon failure of a part such as a hall-effect pick-up plate, or loss of the timing belt. If no reference signal is seen during cranking after a battery disconnect, code 11 will remain. This is a helpful indicator in a no-start condition." (Chrysler did sometimes change codes depending on the year, so it may be that some of these apply to differentyears.)
Where is the solenoid switch located on a 92 dodge ram van?
The starter solenoid is on the starter.
The starter solenoid is on the starter.
How tall is the 2013 RAM CV-Tradesman?
The height of the 2013 RAM CV-Tradesman is 5 ft. 9 in. (69 in.).
Will a 318 transmission fit a 360 in a 1995 dodge van?
the bolt patterns on the 318 and a 360 are the same. so as long as you can "fit" the transmission behind it, in essence, yes. but do your dimensional analysis either way. and consider the t-case and driveline.
No it is located under the glove box. Just remove the Two 7mm screws in the trim panel under the glove box. then look under towards the fire wall. it has 2 wiring harnesses coming off it, a 7 wire and a 2(red and Black).
What is the firing order for a 1994 dodge van 5.2L?
1 8 4 3 6 5 7 2 Distributor rotation clockwise. Looking at front of engine on the right from front to back is 1 3 5 7. On the left is 2 4 6 8.
Where is the horn in a 1979 Dodge van and how is it fixed when it is not sounding at all?
The horn is located behind the drivers side headlight. there is a wire inside the steering column that probably is broken. I've owned my 79 b2500 for 6 years 360 2bbl. only problems ive had is exaust,horn,and windshield washer tank.
Where would the ignition control module be on a 1989 Dodge Ram 350 van?
I believe it is contained in the computer itself. You may not be able to replace it individually.
Try looking under the battery box, For some dumb reason Dodge likes to hide things so you can't find them.
How do you remove arm rests on captain seats in a Dodge Van?
>> On my Dodge Ram Van Class B motorhome, you raise the arm rests all the way up to the stop, then push in and continue rotating toward the rear of the seat.
The above note helped me.
>>On my Chevy Tommy 1987 Class C RV the seat arms were removed the same way with no tools needed. Thank you for that previous answer.
Where is the 02 sensor on bank 1 on a 1997 GMC 1500 savana conversion van with a 57 liter engine?
Oxygen sensors are in the exhaust manifold, right before the crossover or headpipe, depending on which you have. If it says "bank 1" on the code reader, just replace them both. Since oxygen sensors fail after they've served for a while, if one has gone bad the other will be there soon.
