0
Dodge Vans
Dodge has been producing panel delivery models for several years since 1914. However, its first purpose-built van model was launched in 1964 – the compact A Series. The carmaker then released the B-Series, followed by the rebadged Ram Van and Ram Wagon.
462 Questions
Where would the ignition control module be on a 1989 Dodge Ram 350 van?
I believe it is contained in the computer itself. You may not be able to replace it individually.
Try looking under the battery box, For some dumb reason Dodge likes to hide things so you can't find them.
How do you remove arm rests on captain seats in a Dodge Van?
>> On my Dodge Ram Van Class B motorhome, you raise the arm rests all the way up to the stop, then push in and continue rotating toward the rear of the seat.
The above note helped me.
>>On my Chevy Tommy 1987 Class C RV the seat arms were removed the same way with no tools needed. Thank you for that previous answer.
Where is the 02 sensor on bank 1 on a 1997 GMC 1500 savana conversion van with a 57 liter engine?
Oxygen sensors are in the exhaust manifold, right before the crossover or headpipe, depending on which you have. If it says "bank 1" on the code reader, just replace them both. Since oxygen sensors fail after they've served for a while, if one has gone bad the other will be there soon.
How often should you change the oil in a 1994 Dodge van?
You should change the oil every 3000 miles in as 1994 Dodge Van.
Why 96 dodge sport van pull to the left?
Normally a front brake issue, could be an alignment, suspension or tire issue. Check that all suspension parts are in good condition and all connections are tight and that there's no obvious misalignment or disproportionate wear of the front tires. Next, check that front left caliper is not sticking closed and that front right caliper is not sticking open. If calipers are working, try replacing the brake hoses to the calipers, normally the opposite side to the direction it's pulling will be collapsed causing the 'offside' caliper to not close.
Where is the fuel filter location 2006 dodge sprinter?
It is on the driver side of the engine. It is the metal can with the hoses hooked to it.
How do you find a fuse diagram for a 1996 Dodge van?
Which model van do you have? 1500,2500,3500 and which fuse diagram as there is one in the glove box and one under the hood.
What is the diagnostic codes p0442 p0455 on a 2001 dodge grand caravan with a 3.3?
P0442: Evaporative Emission System Leak Detected (small leak)
P0455: EVAP Large Leak Detected
pick-up plate
Where is the blower motor resistor on a 1993 Dodge B250?
On the B250 van the blower resistor is located behind the passenger glove box, remove the glove box shell and resistor is located just to the right side, you can't miss it.
How do you remove a steering column off a 1986 Dodge van?
1.disconnect the negative ground from the battery
2.If it has a column shift disconnect the link rod by prying out the grommet in the shift lever
3.Remove the steering shaft lower coupling to the wormshaft roll pin
4.Disconnect the wiring connectors at the steering column jacket
5.Remove the steering wheel center pad assembly
6.Disconnect the horn wire and remove the horn switch
7. Remove the steering wheel retaining nut. DO NOT HAMMER ON THE STEERING SHAFT TO REMOVE THE STEERING WHEEL.
8. Remove the turn signal lever
9. Remove the floor plate to the floor pan attaching screws
10. To expose the steering column bracket, remove the cluster bezel and panel lower reinforcement
11. Disconnect the automatic shift indicator pointer cable from the shift housing
12. Remove the nuts attaching the steering column bracket to the instrument panel support
13. Carefully remove the lower coupling from the steering gear wormshaft, then remove the column assembly out through the passenger compartment
The distributor induction coil may not be sending a signal to trigger the spark. Wiggle that pigtail wire coming out of the distributor boy and see if the engine will start. If it does, then install a new induction coil. The wires coming out of the distributor body sometimes develop breaks. If the dealer doesn't have the coil, then you can use a substitute Mopar part from NAPA, however, the Mopar part doesn't fit as tight into the distributor body as the original part. Plan to pay about $50 for the part. --------------------------------------------------------------------------------------------- Save the screws from the original part. If I remember correctly, the replacement screws with the Mopar part are bit short.
Computer codes dodge b2500 van po73?
P0073 is Ambient air temp sensor high. Likely cause is the sensor itself.
What is the oil capacity for a 2000 3L Dodge Caravan?
If this has the small filter witch they usally do it will take 4 1/2 qts. Just put the oil in and check and add accordingly.
How do you replace engine mounts on a Dodge Grand Caravan 2005 and how many mounts are there?
It depends on the exact model to which you are referring. Earlier models had three engine mounts; later models used four. If you are not comfortable or familiar with changing engine mounts, your best bet is to see an authorized mechanic, who can do the work needed.
Where is the upstream O2 sensor 1997 dodge 5.2 l?
It is the O2 sensor screwed into the front of the catalytic converter
What does diagnostic trouble code p0031 refer to in a 2001 dodge van?
Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
symptoms
Other than the MIL light illuminating you may not notice any performance issues.
cause
A short in the O2 sensor heater circuit or the sensor itself
A faulty O2 sensor heater
Wiring or connectors are broken or frayed to the sensor or relay
Bad PCM or ECM
The fix
Correct wiring short or loose connector found in inspection.
and/or
Replace the bank 1 sensor 1 O2 sensor
You might have a tire problem, but it probably needs a wheel alignment.
Where is the body control module on a 1995 dodge grandcaravan?
Disconnect the negative battery cable.Body Controller is located behind the instrument panel,left of the center console.Remove floor console or cover to gain access to the body control module.Disconnect the two 25way connectors from the body control module.Remove the mounting screws from body control module.Pull to the left to release body control module of S-clips and remove unit. Ensure body control module is locked into the S-clips when re-installing BCM
