Ford Bronco XLT

www . motorcraft . com ( no spaces ) one of Fords websites lists : Motorcraft batteries : BXT - 65 - 850 BXT - 65 - 650 BXL - 65 BXS - 65

It is a fairly good size job. Remove the Hub, locking or manual. This requires an Alan wrench set. Using needle nose pliers, remove the inner gear that locks the hub in 4x4. Then remove a locking ring that is right at the edge of the hub mouth. All you need for this is an awl. Then you'll be able to see the large locking ring that holds the bearings in. There should be a c-clip around the axle you need to remove. As you remove parts, lay them out on a rag in the order they are removed. You will need a large socket avalible from most auto parts to remove the outer bearing locking ring. Then there is a ring with holes around it that comes off. That will expose the inner locking ring. It is removed with the same large socket. After removing that ring, the entire rotor should come off. Be careful not to damage the inner bearing or the grease seal while removing the rotor. That will expose the spindle. There are 6 bolts around the spindle flange. You need not worry about holding the inner bolt head with a wrench, they will hold theirself. After removing those nuts from the spindle flange. you will have to use a chisel, punch and a hammer to work the spindle loose. Take your time and rotate the prying around the flange. When you do get it loose,the spindle will slide off. Be care not to damage the small needle bearing that is in the inner part of the spindle. Take your time and slide the axle thru the spindle. That's it. It will probably take 2 to 3 hours. Just reverse the process when installing. Goddukee@AOL.com

I believe that is 10 degrees BTDC

The 2011 Hyundai Tucson has front wheel drive.

remove the shroud covering the steering coloum and turn the key to the on position push in release pin over ignition and pull cylinder out.

You can't. The days of doing tape measure alignments are long gone. It requires a machine with a built in computer. Costs around $65.00.

.

The 2012 Toyota Venza has front wheel drive.

An intermittent miss in a 94 Caprice could be something in the ignition system. Check the plug wires and ignition coil to start with.

5 w 30 ( according to the owners manual )

The 2007 Lincoln MKZ has front wheel drive.

The 2001 Toyota Corolla has front wheel drive.

The 2012 Toyota Tacoma has rear wheel drive.

NO the dash doesn't have to be removed. There should be a panel under the dash that is black and have a bunch of 7 mm screws securing it to the firewall/other plastic.

that would depend on the tranny

the head is blown , or is about too . This must be a 3vze v6. If so it is probably a blown head gasket. They had a recall on this, maybe over now though I dont know. This is very common on the v6 aluminum head and iron block. New head bolts and an upgraded gasket is a good fix. dealer waranty under the recall is a better one.

The 2008 Kia Optima has front wheel drive.

OP here-

Got it looked at and the entire distributor went out. Problem solved.

Heater core should be behind glove box. Remove glove box and screws( approx. 8) that holds cover in place. Pop hood and look for two hot water lines running into firewall at that location(passenger side) Remove lines by loosening hose clamps(advisable to replace) Remove heater core from inside and replace.

The 2001 Acura MDX has four wheel drive.

The 2013 Toyota Prius-V has front wheel drive.

On The Corsa 1.4 Firing Order 1-3-4-2

The switch in the glove box is to de-activate the power trunk switch located on the drivers side door. When leaving your car with a valet, the secondary key will not open the trunk or glove box. Only the primary key has total access.

The 2014 Ford Escape has front wheel drive.

The 2011 Honda CR-Z has front wheel drive.

A Mini Cooper will be fully crushed by a monster truck. It will most probably not get stuck in the tires of the large Monster Truck you plan to drive over it, though.