0
Ford Falcon
Manufactured between 1960 and 1970, the Ford Falcon was a huge success for Ford, surpassing its rival compacts from General Motors and Chrysler. It was produced in various body styles, such as 2-door and 4-door sedans.
937 Questions
Are the front lower ball joints on a Ford Falcon xr6 2003 bolted or riveted?
hi, el thru tobf xr6 are all pressed in . by a bearing press. kerry
What does dte mean on a Ford Falcon au dash mean?
It means Distance To Empty. It's refering to long many kilometres you have until your fuel tank runs out of fuel.
Also note that 80 kh it will change higher number under less in 400kms Over 80 kh 900 DTE
How do you change the power steering belt in a Ford Falcon Series II EB?
To change the belt just loosen off the big nut around the ajuster with an appropiate spanner or shifter. This will slacken the belt off. Remove belt. Put new belt on. To adjust the belt get an appropriate double hex spanner and put it on the inner adjuster and turn it until the right amount of tension is applied and the then whilst holding the belt tight, just tighten the outer nut and it's all done.
Yes. If it is a six cylinder, you need a 65-67 Bell housing for a 170-200 IL. You can get it off Ebay. You need the block plate, and dustcover. You need to shoten your drive shaft. Change the yoke to 28 spline. New torueconverter. Flexplate will work. You will need transmission mount and bushing. Possibly need starter. You also may have to drill the top of Bell for lever assembly. Now for the tricky part, steering coloum. Needs need ident plate. You need to find or fabricate new linkage. Kick down. Or install a floor shifter. Final drive ration is still one-one. I would consider a t5 conversion with OD. or gear vendors OD.
Are there lifting brackets on the engine of a Ford Falcon 1996 ef sedan?
Yep, normally should be on the R/H side at the back, attached the the exhaust studs, and one on the l/h side at the front!
How do you remove a ba falcon tailshaft?
Remove the 6 bolts into the diff.remove 2 bolts holding centre bearing to body,lower tailshaft from diff,slide tailshaft out from gearbox,on automatics oil wont come out if car is level, u need to note markd on talishaft and diff, good luck with any vibration vibration vibration....
How do you remove a 1964 Ford Falcon ignition switch from the dash?
To replace the lock cylinder, insert the key and turn the cylinder to the accessory position. Insert the end of a paper clip into the small hole in the face of the cylinder. Continue turning the key counterclockwise while gently pulling on the key. The cylinder should come out after the key is turned approximately 1/8 turn past the accessory position. Once the cylinder is removed, with one hand hold the ignition switch bezel on front of dash firmly in place, while at the same with the other hand reach under the dash, and press the switch body against the back of the dash to compress the spring and turn the switch body counter clockwise. The bezel and body will separate. Gently pull the switch body out from the back of the dash, separate/pry the rubberized wire harness from the switch. Reverse procedure to reinstall. To install the new lock cylinder, index the cylinder so that the key is turned approximately 1/8 turn counterclockwise from the accessory position. You will probably have to insert the paper clip into the hole to turn the key. Insert the lock all the way into the switch and turn the key clockwise until the cylinder locks in place. believe the front chrome trim piece is actually the nut.
How do you change Ba falcon spark plug?
The spark plugs are under the central plastic cover on the top of the rocker cover - the coils are just under the cover..... my advice is to leave this to a dealer or a licenced mechanic who will do the job and not damage anything!
theplugs are easy to remove with exeption to the one closest to the firewall if you take your time you will be able to do the job without damaging anything you will need some long nose pliers to remove the loose plugs make sure you put some lubricant on the contact ends so the bubber boot will slip on again easily ! do the job yourserlf and save money good luck
How do you fit the drive belt on an ef falcon there are a lot of pulleys. What is the configuration?
hi there. on the underside of your bonnet there should be a diagram of the belt configuration and how to install the belt. do you have a manufacturers manual in the glove box?
How do you find a fuel relay on a Ford Falcon 1994?
under the bonnet, on the RHS to the RHS of the battery). There's 6 in a row. From front to back they are:ABS, SLS, WAC, ECU, FUEL PUMP, ABS. So 2nd from the back.
Where is the fuse box on a 1962 Ford Falcon Ranchero?
Where is the fuse box on a ford falcon ranchero 62 model
Where is the brake light fuse on a 1963 Ford Falcon futura?
It is in the fuse box which is bolted to the headlight switch. You need to remove the headlight switch ti access it.
Where is the relay switch for the lights in 1992 Ford EB Falcon?
behind the battery there are 4 relays it is on the end of the holder it is silver in colour i just replaced one my self
How do you replace the Ford Falcon 2000 vehicle cigarette lighter?
You do not need to take out the centre console all you do is turn the plug anti clockwise with either your thumb or something that fits in the hole and it will slowly pop out.
What are some of the features of the Ford Falcon XR6?
There are many features of the Ford Falcon XR6. They are USB integration, 8-inch color touch screen, curtain airbags, front seat side thorax airbags, projector headlamps, etc.
How do change front left blinker bulb on 1997 el Ford Falcon?
got to take the quarter panel off, four bolts in the engine bay, two underneath, one with the door open (remove black trim on forward edge of doorand horn will need to be unscrewed, just one small bolt for each, also the headlight . don't undo to aerial, just take the blinker plug and give it a twist to remove the bulb assembly. usually if you put the panel back on tight the door and bonnet gabs are correct but slight adjustment may be needed.
How do you change the front wheel bearing on a Ford Falcon AU?
What you do is, you remove the tyre by removing the wheel nuts, then you remove the brake caliper by removing the 2 bolts holding it in place, and the brake disc after that. Depending on the type of bearing it uses, you may need a flat head screw driver to take the old bearing off. When you put the new bearing on, make sure it's properly greased before you put it back on. Then you put the disc back on, caliper and tyre. Make sure the disc is on the steering rack properly
You can buy the EB Falcon coil replacement at the online websites like Ebay.
What years was the Ford Falcon produced?
The Ford Falcon was produced by the Ford Motor Company from 1960 until 1970. This was Fords attempt at producing a compact car.Ford replaced the Falcon with the Ford Maverick.
What is the cost of a 1968 Ford Fairlane?
My dad picked one up for ten grand, and it was in pristine condition with no rust
Check the voltage at the brake switch. See if it is adjusted properly to turn the switch ON when the brake pedal is pushed. If that works but the brake lights still do not come on, check the turn signal switch inside the steering column. You will have to remove the steering wheel. Rent or buy a wheel puller, remove the horn button inthe middle of the wheel, remove the horn wire from the electrical connector in the wheel, remove the large nut that holds the wheel in place then use the wheel puller to pull the steering wheel. There may be a large washer looking piece of metal over the switch. The turn signal switch disconnects the brake light for that side when you turn on the signal then the turn signal flashes on that bulb. If the turn signal switch is damaged or just plain worn out it will stop working. Also the problem maybe the bulb panel, for lack of a better word. This is where the three bulbs plug into behind the rear lens. It has a main pig tail that plugs into it giving it power and ground. When the connections in the panel go bad from breakage or corrosion they have to be replaced, around $30 a set.
How do you change the alternator belt on a 1993 Pontiac Bonneville?
Use a wrench to loosen the tensioner which keeps tension on the belt. Once this is loose, pull the belt off of the tensioner. It will then come loose from the remaining pulleys (A/C compressor, water pump, etc.). A diagram should be located on top of the radiator showing the path of the belt to help you know how to install the new one.
How do you remove a 1964 Ford Falcon wiper switch from the dash?
remove the knob first - set screw on that one I think - then look for notches in the bazel Ford had a special tool but you can use a needle nose plier with a little tape on the ends to unsrew the bazel - carefull not to mar the chrome
How much for a rear window for a 1965 Ford Falcon?
1963-1965 rear glass the same on Falcons. About $290 plus shipping, try dearbornclassics dot com. About $150 used if you can find one.
