Ford Probe

Usually this is a two man job, but it can be done by one by doing the following: Get a piece of clear quarter inch PVC tubing, about 2-3 feet long. Place tube over bleeder valve outlet. Put other end of tube into a clear water bottle that has been thoroughly dried. Fill water bottle with about 2 inches of clutch fluid, enough to cover the end of clear tube. Now, open the bleeder valve on the slave cylinder a quarter to half turn. Open clutch master cylinder reservoir and top off. Now place the bottle with the tube in it in a place where you can see it from the drivers seat. Now slowly pump the clutch pedal as to not whip up air bubbles into the clutch fluid. Now keep an eye on your clutch fluid level throughout the process. Never let the clutch reservoir run dry, or you will have to do it all over again... what we are trying to do is watch for air bubbles in the fluid that moves from the slave cylinder to the water bottle via the clear tube. Once there are no more air bubbles in the clear tube, close bleeder valve. Repeat if necessary.

if you look at the front of your tranny. there will be a plug 15/16 big take it out and tranny fluid should come out. if not use a Allen key to put in the hole.

transmisions are complacated take to a good shop./

1. Remove the screws and pull down on the front portion of the fender liner. This provides just enough room for your hand to reach in and access the two bulb holders.

2. Turn the bulb holder counterclockwise and pull it out of the housing.

3. Pull the bulb from the holder and replace.

You can often find exploded views of the 1993 Ford Probe's 4EAT automatic transaxle in service manuals or repair guides. Websites like eBay or Amazon may have these manuals available for purchase, and online forums or automotive repair sites might also share diagrams. Additionally, you could check with automotive parts retailers or local libraries for access to repair manuals that include exploded views.

Raise the car on ramps or jackstands. Drop the crossmember between the two front A-arm mounts. It has four large bolts. put a jack under the engine cradle member that attaches to the mounts and the subframe. Unbolt both mounts from the engine and put a jackstand under the oil pan or the transmission. Make sure it's tight and not allowing the engine to move but there is a 3rd engine mount on the passenger side top of the engine that will not allow it to fall but you want to keep everything aligned for ease of service.. Then unbolt the engine cradle and lower the cradle with the mounts still attached. Change the mounts and do everything in reverse. Use plenty of PB blaster for an easy job!

-JLove

Can a supercharger work on a 97 ford probe

Ford probe cars are available through various 2nd hand car dealers as well as directly through online merchants. Many models are available on the Autotrader UK website with a starting price of 695GBP for a 1995 model.

WAIT UNTIL ENGINE IS COLD - DANGEROUS TO DO WHEN HOT OR EVEN WARM...

First - remove the air intake. You'll see there's a few bolts holding it in. Removing it will open up access.

Pay attention to which bolts go where. Take a couple of digital photos as you go so you can see which bolts are screwed into which parts when you put it back together later.

You need to disconnect the hose on the left side running into the radiator. Do this by using pliers (or similar) to squeeze and loosen the clamp (or unscrew if it's a screw-in clamp). When lose, slide the clamp back down the hose and then you'll be able to wiggle the hose loose.

Repeat this for the smaller hose on the right side and also unbolt the secondary mini overflow tank thing next to it.

Ideally you need to SAFELY get below the car, undo the clamp on the bottom right side and all the hoses will be disconnected.

Disconnect the fans. There are electric clips that you can undo (don't yank it, there is a simple mechanism) in front of each fan.

Now you hoses and fans electrics are not connected, then you can undo a small number of bolts at the front (from the top) that hold the arms that, in turn, lock and hold the radiator into place. Once the bolts are off, the arm just slides off and then you can pretty much pull it straight out.

There are

Under hood, passenger side, lower engine area, above crankshaft pulley, mounted in engine block

Probe,probe se 2.0 / probe gt 2.5

it needs brake fluid

Easy: you call a professional to do it.

The Probe windscreen is bonded directly to the car and is not a job for the DIY-er.

no, they are different body styles.

Yes both the probe gt and Mazda 626 have exact same engine and equal power, 24valve DOHC V6.

Yes

whether you have the 2.0 or 2.5, the location is almost the same. At the top of the radiator, find the upper rad hose. Follow it back to where it connects to the engine. The metal housing that the hose is clamped to is the thermostat housing. Remove the two bolts from the cover and the thermostat is hiding inside.

2.0 marshal long block.............$2,529.79

2.5 marshal long block.............$2,584.79

code 12

Under the dash on the driver's side, mounted in relay block netween the steering column and kick panel

the filter is internal and cannot be changed unless the trany is taken apart, ur better off to just change the fluid and if its really bad change it again in about 2 weeks just so that it can be cleaned out.

There is a C-clip between the handle and the door panel. There is a special tool you can buy to get it off - from an auto parts store. If you do it once, you'll see how simple it is!

the slave cylinder is easy to replace. you cant dissassemble it. to replace it simply look down where the engine and transmission meet from under the hood. you will see a line and a bleeder screw. from there just disconnect the line, plug it, and remove the two bolts holding it in. installation is reverse. just remember to bleed the air out of the lines by cracking the bleeder screw and have someone pum the clutch until the air is out

16... that's a dumb question

Wrong! It's a 12 valve engine(3 valves per cylinder)... that's a dumb answer

-nitrodruggie