0
Ford Ranger XL
The Ranger XL is a pick-up truck manufactured by the American automaker Ford Motor Company. Some of the notable features found in the 2010 model are Electronic Stability Control, and torso and head airbags in the front seat.
4,911 Questions
Why do you have no spark on cylinders one and four?
on a lot of gm cars cylinders 1 & 4 fire off the same coil.
How do you unfreeze a frozen engine?
If you mean frozen as in seized, the engine will need to be rebuilt, as parts have welded themselves together and there is most likely some serious damage to the pistons and cylinder bores.
How long will it take to drive 257 kilometers if you drive at 110 kilometers per hour?
We have to find the time now so the formula for time is Distance/Speed.
=257/110
=2.3 hours
Remove crankshaft pulley ford ranger?
i removed it buy placeing a braker bar on the nut and wedgeing it against the frame of the car then click the starter one or two times that should break it loose
Where is the OBD Test Plug located on a 1998 Ford Ranger 4.0?
It's in the lower part of the dash , below the steering wheel , behind a small
removable plastic panel between the inside hood release and the parking brake
release
Where is the fuse for the anti-theft alarm on a 1996 Camry?
look behind the chang box there are a group of fuse their i have a 96 camery and there is a group of fuses behind the change box in the car
How do you operate the spare tire carrier on a 85 Nissan pu 2wd?
Get the long section of the screw jack handle that came with the truck and insert the end that fits into the screw jack throught the slotted hole above the rear liscense plate location. Engage the end of the jack handle into the spare tire crank mechanism. Place the screw jack turning handle onto the long jack handle and turn counter clockwise to lower the spare tire.
How do you add fluid to the rear pumpkin on a 2003 ford ranger?
must use a hand pump like used to fill mercrusier out drives juat ask for at your parts store
Where is the horn relay located on a 1996 ford ranger?
On your 1996 Ranger , the horn relay is in your power distribution box in your engine compartment , it is in the 2nd row from the driver's side and it is the first relay at the front end of the PD BOX . Ford recommends disconnecting your battery before servicing any relays/fuses in the PD BOX which means your Ranger would have to re-learn its idle etc.
What size is the gas tank in a 2006 Ford Ranger?
In a 2006 Ford Ranger :
The ( SuperCab ) is ( 73.8 litres / 19.5 U.S. gallons )
the simplest way is to undo screws holding contactor in place then change wire for wire approx cost $40 you will neeed to turn of power at the furnace and at the outdoor unit as there is both high and low voltage at the contactor
This is a good question because the contactor and capacitor are some commonly ruined yet easily replaced components. It would be helpful if someone explained in laman's terms how to remove the possibility of being electrocuted while replacing a contactor and capacitor. I know one way is to attach something called a "resistor" to some part of the capacitor, but I'm not sure about the specifics. There is probably a way to discharge the voltage with a household item, but I'm not aware of it.
Where is the instrument panel on a 2000 Ford Ranger?
The instrument panel is the gauges and warning lights that are in front of the
driver and behind the steering wheel
How many quarts of oil go in a 1990 ford bronco 2 2.9 liter V-6?
1990 FORD BRONCO II 2.9L 6-cyl Engine
CAPACITIES
Engine, without filter..........4.0 quarts [1]
Wix Oil Filter.........51515
Cooling System, W/O AC Initial Fill..........7.4 quarts
Cooling System, with AC Initial Fill..........8.0 quarts
Automatic Transmission, Initial Fill..........3.0 quarts [2]
Automatic Transmission, Total Fill
2wd ..........9.0 quarts
4wd ..........10.0 quarts
Manual Transmission, 5-SPD Mazda..........5.5 pints [3]
Manual Transmission, 5-SPD Mit..........4.9 pints
Differential, Rear..........5.1 pints [4]
Differential, Dana 28 Front..........1.1 pints [5]
Differential, Dana 35 Front..........3.6 pints
Transfer Case,Warner 1354..........2.5 pints
Transfer Case,Warner 1350..........3.0 pints
1. When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase.
2. With ENG at operating temperature, shift through all gears. Check fluid level in PARK and add fluid as needed.
3. Mazda TRANS has drain plug is on the driver's side of the case. Mit drain plug is at the center of the pan.
4. Fill to no more than 1/4 to 9/16" below fill plug hole.
5. With Dana 28: If fill hole is at centerline of axle must have lube level no higher than 1/2" below fill hole. Models with fill plug below centerline of axle must have lube level no higher than 1/8" below fill hole.
Hope This Helps.
How do you get a fuse panel diagram for a 96 e350?
If you spend 14.95 get an account with AllData and you can print out all the electrical schematics.
How do you change a fuel pump on a 1997 Ford Ranger?
go to autozone.com and you can yse the online repair manuals and print out step by step instructions to replace the fuel pump
AnswerDrain the fuel tank, disconnect the fuel tank straps, disconnect the hoses and electrical connector from the fuel pump, use a spanner wrench to loosen the nut securing the pump to the tank. Installation is reversal of removal. Now here is a better idea, cut a hole in the bed of the truck and remove it that way and/or reove the bed of the truck and slide it away from the tank. Your choice!Better answer
The best way to change the fuel pump is to take the bed off the truck, it is very simple. You have 6- T-55 screws in your bed remove them. Disconnect the filler hose, it is 3- screws forgot the size. Its a small metric. Remove to gas cap, and take the tail lights out and bulbs. Extremelely easy, its really hard to get the tanks back into place even without fuel. You would need atleast two people to replace it. But all the tool you need is a t-55 hex, i believe a 8m socket and a Phillips screwdriver.
***** ^ is the best answer, but to clarify, the filler neck bolts are 7mm, and all you need to do is unplug the tail light assemble harness located under the rear bumper and the lenses and bulbs can be moved with the box.
What is all needed to swap a 2.3l for a 4.0 in a 93 ford ranger?
you need whole harness and dash and a few dollars to add on topso as to to swap a 2.3l for a 4.0 in a 93 ford ranger.
you could check for oil pressure , could be a fault in the oil pressure sensor that is holding the pump out. i have seen some of these trucks have a loose ground wire near the fuel pump also
cutlikeabuffalo oil pressure? its not running yet!!! electric fuel pump has nothing to do with oil pressure before start-up. check for fuel supply to throttle body or rails. a fuel pressure test will determine sufficient supply,u could also just loosen a fitting to check for presence of fuel being pumped up to engine. restriction could also be due to clogged inline filter or blockage at pickup tube inside tank. This would more likely generate a rough running or low power condition , however it "should" still fire. Check for power to pump @ connector 3pin near driver side rear of truck wire loom going from frame rail to pump at top of fuel tank, yes it could be a poor ground. Ground wire from pump side of connector to frame. If no power work forward from there. Check breaker/ fuse/ relay and wiring. a point to point voltage drop test would be the best way to locate hidden resistance in the wiring , a break, short ,or corrosion. If good power and no fuel, either pump is not running, (u can usually hear it work when key is first turned on for a few seconds) or there is a restriction.
Why doesn't your temperature rise to normal while operating your 1995 s10 blazer 4.3l 4x4?
Stuck open thermostat.
What is location of fuel pump relay on 2000 ford explore xl.?
# 5 relay in the power distribution box in the engine compartment is the
fuel pump relay for a 2000 Ford Explorer ( the P D Box is " live " )
