How do you replace a radiator on a 2000 GM jimmy?
Caution:On models equipped with Delco-Loc 2 or Theftlock audio systems make sure you have activation code * Disconnect the negative battery cable * Drain the cooling system * Disable the airbag system.Disconnect the forward discriminating sensor harness from the front fenderwell.It may be necessary to remove the hood latch mechanism in conjunction with the airbag sensor and secure them together and out of the way during the radiator removal * Remove the cooling fan assembly * Disconnect the upper and lower radiator hoses from the radiator then disconnect the coolant recovery hoses at the radiator neck * Remove the automatic transaxle cooler lines if equipped from the left tank of the radiator * Remove the hood latch support from the upper tie bar on the front of the engine compartment * Remove the right and left headlight assemblies from the vehicle * Remove the condensar mounting bolts from the radiator assembly * Remove the tie bar (crossbeam) from the engine compartment * The radiator can be removed from the top with some wiggling to clear various components
Between the grill and the radiator are three or four posts (I cant remember exactly how many, but you will be able to see) which hold the emblem in place. Using a flat head screwdriver gently lift up and push on the tabs inside of grill. This will release the emblem.
Where is the oil pressure sending unit on a 94 gmc jimmy?
I believe it is on the back of the engine. back by the distributor cap and such.
Looking at the motor from the front, it is behind carb and to the right of the distributor. It has 3 wires on it.
How do you remove a stuck ignition key from a 2004 Chevy trail blazer when the battery is dead?
First, replace the battery. Then, cycle the ignition between on and off three times. Turn the ignition key into the on position, then the off position, three times. The computer will recognize the key, reboot the computer, and release your key.
the simple answer is YES. though, a 94 would be either a t.b.i. system or early vortec. if it is a vortec, the swap shouldn't require a p.c.m. reflash- however if your 94 is a t.b.i. you will need to change the intake and fuel delivery systems to handle the 60 p.s.i. operating pressure for the vortec engine.
How do you remove heater core from 1998 GMC Jimmy?
i believe my 99 calls for like 10 hours labor. gott aremove the front fender etc. pain in the butt
IF YOU REMOVE THE FRONT FENDER TO GET TO THE HEATER CORE YOU MUST BE POLISH, THE HEATER CORE IS BEHIND THE DASH INSIDE THE DUCTING, YOU MUST DROP THE STEERING COLUMN AND REMOVE THE DASH (7SCREWS) PULL THE DASH BACK TO GET ACCESS TO THE HEAT AND AIR DUCT AND THEN REMOVE THE TOP OF DUCT AND THEN YOU WILL SEE YOUR HEATER CORE
Where is transmission control module on gmc jimmy?
My understanding is that it is built into the PCM Powertrain Control Module. This would be the Black rectangular box mounted inside the engine compartment on the passenger side fender. If you want to see what one looks like, do a search on Ebay as if you are trying to buy one. There you will find a picture. There are many, many systems that control or add to the management of the 4L60E transmission. If you are needing to know where the transmission control module is, I wish you great luck with finding it.
Where can you get advice on removing the engine in a 1996 GMC Jimmy?
Get a Haynes or Chilton's manual for your truck. They are detailed enough for what you want.
Replace the ignition switch for GMC Jimmy 1991?
The mechanical switch itself is rod actuated and located under the dash bolted to the steering column. Remove and trim panels to expose the column bracket. mark the location of the shift indicator clip, and remove with a small flathead screw driver. drop the column and it's right there ,I think it's has two 7mm screws holding it on.
If you are talking about the key cylinder itself you will need to remove the steering wheel, remove the plastic lock ring cover, if you have an air bag there is a ring with yellow wres coming in and out if it, this you CANNOT turn this ring w/o causing damag to the unit and rendering your airbag useless and eht airbag light to come on, remove it carefully and set it on top of the column. With a special tool press the locking ring down and remove the snap ring. After the locking ring is removed you expose the turn signal switch/cam, remove the screw on the left of the cam that attaches the turn signal arm to the switch, and remove the emergency flasher button, both should be Phillips head. After the arm and button are removes remove the 3 screws that old the switch in place. GENTLY pull up on the switch, making sure not to break the wiring harness. There is a small plastic and copper connector over a torx head crew, remove it with needle nose pliers being careful not to damage it, this is the terminal that make the buzzer go off when you open the door and leave the keys in the ignition. Now remove the torx head screw and slid out the key cylinder. Re-assemble in reverse order.
yes it can be done... but take this into account, with the spare on the back door of the blazer/jimmy if you are bumped in any way the shock will break your rear window glass ($400.00) i removed mine.. think about it before you invest
It might be a partially blocked fuel injector or low fuel pressure or possibly even a partially blocked fuel filter.
Where is the fuse for the electric seats on a 1999 GMC Jimmy?
there are two fuse panels. one is on the left side of the dash,you can see it when you open the drivers door on the left side of the dash. the other one is under the hood on the drivers side. it says fuse relay center right on top of it. check both of these. hope this helps.
How do you recharge the ac on a 91 gmc jimmy?
you will have to take it in to have it serviced because of the r-12 coolant. ask about possibly flushing it out and updating it with 134. unfortunately, the ac process, either one, is not a cheap one...
Can you lubricate Air Conditioner Clutch?
No, oil will ruin the clutch.
Noise that sound like you need oil means a bearing or the compressor has failed.
How do you change a heater core on an 1996 gmc jimmy?
It's not fun, but you need to remove the entire dash and unplug the electrical connections going to it. You need to also unbolt and drop the steering column, and then take the dash completely out. Once it's out, the heater core is easily accessible behind it's panel on the firewall. (Looks like a little radiator.) I would recommend getting a service manual to assist you, or getting pictures online.
The remote won't open the back tailgate latch in 1997 gmc jimmy. I can't find owner's manual. How do you manually open the back window?
What causes transmission fluid to gush out of the dip stick while going down the road?
dipstick o ring missing,wore out or dipstick is not in good
Replace just the mirror unit (complete with cover). They are sold on ebay for between $15 - 25 per unit. You don't have to replace the entire visor.
Try having the Fuse Block checked out, had the same problem on a 1999 gmc jimmy, and the repair OS going to run about 500 bucks to get the block replaced, or 160 to get the fuse connector to the fuel pump IN the fuse block repaired.
What would cause the push button 4x4 not engage on a 1994 GMC jimmy?
There is a part called an actuater. It looks like a plunger. They are natorious for dry rotting and the four wheel drive being engaged is on a vaccuum system that involves the actuater. Once that gets a hole in it, it stops the vaccuum and will not engage. It costs about 65 dollars and is about a 15 minute job to fix. It is located under your car battery. Remove your battery and the battery plate that your battery sits on and you will then be able to see the actuater. Once you see it, it is self explanitory on how to remove. Call your local gmc dealer to obtain part.