Hyundai

where is the catalytic converter on 2000 hyundai accent gl

does the 2010 hyundai santa fe have an on off overdrive switch where is it located

Low compression in one cylinder can mean several things. The valves or piston rings may need to be replaced. There may be a crack on the engine, or the head gasket may have blown. The engine should be diagnosed properly to see what exactly is the cause of the low compression.

The passenger side bulb is much easier to replace than the driver's side, and I suggest you use it as a visual aid.

On the driver's side, you will need a Phillips screwdriver to loosen the three plastic screws that attach the shroud to the front of the car. These screws do not come out, they simply anchor the plastic clip through the metal. When the screws have come up about an inch, gently lift the shroud & set it out of the way to the left. You can also remove the 10mm bolt at the other end of it, but it is not necessary. Just be gentle as you shift things. On the passenger side, you can simply work around the windshield washer fill tube.

The headlight enclosure has an airtight cap on it, which you remove by turning slightly counter-clockwise from behind, facing the front of the car. Pull the electrical connector straight off the back of the bulb. The bulb itself is secured by a brass-coloured bent-wire do-hickey. To remove the bulb, you simply press the wire where there is a rectangular bend on one side near the bottom, next to the silver screw. The wire will unhook and you pull it up out of the way, freeing the bulb. (If you are working on the driver's side, go have a look on the passenger side to see how it works.) Pull the bulb out, being careful not to hit it on anything. Note that the metal ring around the bulb has the notched part at the top.

Now put the new bulb straight in, with the notch at the top. Hold the wire do-hickey up out of the way as you slide the bulb in, let it drop back into place while you keep the bulb in place (I placed a finger on the connectors to do this), then press the wire rectangle to hook it back on. Put the connector back onto the bulb and replace the black plastic cap on the assembly. Check to make sure the light works before reattaching the shroud. Replace the passenger side cap if you've been using it as an aid. I know, I know, but we've all forgotten something under there once or twice.

Gently move the shroud back into place, & put the plastic clips back into the holes - if the screws dropped back into the clip you will have to pull them out or the claws of the clips won't fit through. Tighten the screws and Voila! You are safely lit once again.

The 2008 Hyundai Elantra is 14 ft. 9.4 in. (177.4 in.) long.

53 liters on all models

P0133 is a trouble code for o2 sensor, what it means is 02 sensor slow response bank1, sensor 1 (before cat) should be located before the flex pipe. What causes this code is that there are many reasons, one could be a faulty sensor, a bad exhaust leak or minor usually happens if the leak is before the sensor depending on which leak is greater. vacuum leak can cause this code due to not enough oxygen entering the exhaust manifold. check with the dealer or local garage, it is very hard to actually state which problem is causing this code.

Mine was coming on due to a massive exhaust leak, when fixed the code disappeared.

hiunday excel 3 doors engine 1500cc

leadership through listening

possible siezed linkages or motor. common for linkages to get siezed,

I just ran across this answer by coincidence yesterday. Depends on what system you have but if you log into http://www.hmaservice.com/authenticator/login?returnAddress=http%3A%2F%2Fwww.hmaservice.com%3A80%2Findex.jspthey have all the details on resetting/setting this function.

Look under the car, it's easily accessible from the front on the passenger side near the bumper area.

msrp:$17,270 - $22,770

Diagnostic: "module Tank Leakage (DMTL) Failure" Probale cause: 1) Open Or Short Circuit Condition 2) Poor Electrical Conection 3)Faulty DMTL Module Faulty

All Hyundai accent in that year physically don't have that code

they will start in p0,p2 and u0 . None start in p1

The 2002 Sonata has a timing belt. Timing chains were not introduced until 2006 Sonata.

how do I replace a mass air flow sensor on a Hyundai Accent?

The company is Hyundai Kia Automotive Group and produces both makes. Hyundai owns controlling interest in Kia Motors but they are two separate companies.

http://www.elantraxd.com/DIY/sands.php

There's a step by step tutorial at ElantraXD

Photos included

There are multiple YouTube videos that show a step-by-step tutorial on changing a windshield washer pump. You will use tools to take the screws and brackets off holding the washer pump on and replace it with a new one. It can be done at home by a novice.

should be were the fuses are, under the engine hood

where is evap canister on 2003 Hyundai sonataType your answer here...

The height of the 2006 Hyundai Sonata is 4 ft. 10 in. (58 in.).

The turn signal on a 2004 Hyundai Elantra is found behind the cabin fuse box. The flasher will be plugged in next to the fuse box.

New car models are typically released July- October the year before. Sometimes new models are exhibited at summer car shows.

See the related link for more information about specific models.