0
Isuzu Trucks
The Japanese company Isuzu Motors is known for producing medium to heavy duty trucks. Some of the Isuzu trucks are the Hombre pickup truck, D-Max, i-280/i-350, NHR (Elf) light truck and CXZ (Giga) heavy truck.
628 Questions
Will a Holley 5200 off a Ford Pinto fit a 2.3 Isuzu engine?
Yes, but if you're looking for performance, you might want to go with something bigger, like a weber dges.
To get a holley 5200 to fit on your engine, you have a few options. The easiest would be to see if you can get a redline weber adapter plate. Check their website, http://www.redlineweber.com/HTML/application_guide/ISUZU.htm and see if your exact engine model is listed there. The weber dgv 32/36 carb has the same base pattern as the holley, the holley is actually a liscensed copy of the weber. Try to get an adapter plate for your engine off eBay or something, and the holley will bolt right on to your stock intake manifold your second option, if you can't find an adapter plate for your engine, is to have a machine shop make a plate or modify your intake manifold to fit the carb. A third option is to build a custom intake manifold, but don't even think about this unless you know what you're doing.
Flasher module location for 1998 passat?
The flasher module for a 1998 Passat is located behind the emegency flasher button. The button(cover) pops off and the module can be pulled out with two pairs of needle nose pliers(one on each side) and unplugged from the electrical connector.
Where is the screw holding on the rear brake drum of a 1991 Isuzu pickup?
on the outboard side near the lugs.
Where is the turn signal flasher on a 1997 Isuzu Hombre?
Turn flasher is near the cigarette lighter but its on the second/ right round aluminum can, cause the left can is a hazard relay switch just clean the connector with sand paper, due to time of use dirt or just oxidation is on the terminal. And it has 2 terminal only, if you buy new one it has 3 terminal.
Where is the flasher location on a 1991 Acura Legend?
Im not quite sure as to what flasher you are speaking of but if its the emergency flashers those are on the dash next to the clock. If you mean high-beam flashers just flick the high beams instead of a full click and it flashes for you.
How do you time a 4hf1 Isuzu engine?
Hi,iv'e got a 4hf1 isuzu. What will the correct compression reading be if i do a test on the engin?
Where is the horn relay on a 1994 Isuzu pickup truck?
On the 1996 Hombre it is in the glove box on the passenger side of the car. They may not have moved it that far in 2 years.
How do you repair a clutch that's fallin through a firewall in a 1990 Isuzu pickup?
I had this problem a few times. First fix was a piece of ply wood on the engine side of the wall with the cable through a hole in the ply. Second was 1/4" thick aluminum about 2" wide with about a 1" hole for the collar piece on the firewall, (engine side) It lasted maybe 8 years, but the fire wall cracked in too many places and finally failed completely. Last year I got two pieces of 1/16" steel and shaped them to sandwich the firewall. The driver side piece had an angle welded to the right side. This welded to the rib on the right side of the clutch cable hole after the plates were bolted with the existing bolts. The engine side had a strip welded on the top edge (to form an angle) that was welded to the "gutter" rib that runs across the upper part of the firewall. Once completed, I could shift again without grinding those expensive gears. It's worked like new ever since.
Where can you get a wiring diagram fo an Isuzu truck?
Try this site... http://www.isuzutruckservice.com/bodybuilder.php
Find your model and download the PDFs.
Cheers
Willy (Australia)
What is the torque setting and torque pattern for an Isuzu FSR truck engine head?
torque on Isuzu engine head for 4hf1 is 95 lbs
How do you check a firing order?
Hi, ALL 4 cylinder vehicles use 1-3-4-2 as the firing order. Number 1 cyl. being the one closest the front or belt end of the engine. If the vehicle has a distibutor you need to take the cap off and bump the starter to see if it turns counter or clockwise. If it has a coil pack you can go to a parts store and sneek a peek in the proper repair manual. If the index does not reference 'firing order' look in 'tune up' or 'engine electrical' it will be there. Good luck.
How do you check for fuel leaks?
Grab a light and start looking. Might have to start the vehicle so the system pressurizes, but it's a visual inspection.
Wiring diagram for a Isuzu NPR?
A wiring diagram can be found at this website: http://www.abcccodes.com/95-isuzu-npr-wiring-diagram/ for the Isuzu NPR. The diagram can be downloaded as a PDF file.
What are the timing marks on a 92 Isuzu pickup with a 2 6 fuel injected engine?
There are three marks to line up... before you remove the lower timing belt cover there are the marks on the little gauge that is integrated into the cover that line up with a mark on the main crankshaft pulley (to actually time it while the engine is running) there are also marks on the camshaft sprocket (big sprocket at the top of the engine seen with the upper timing cover removed), that lines up with a white mark on the upper rear plastic timing cover. And finally if you replace the timing belt there is a mark on the crankshaft sprocket that lines up with a mark cast in the face of the aluminum engine block. mnemonic76 1988 Pickup owner
How do you replace Rodeo oxygen sensors?
They just screw into the exhaust pipe. There are clips that keep the electrical connectors in place, you will have to pry those out, but it should not be a problem. Then all you do is screw the new one back in, and press the clip back into the hole for the elec. connection
Well, i am in the process of changing the sensor as we speak...and i am dirty and hot (yuma, september, over 100 degrees Fahrenheit, shoot me).
I bought my new sensor from Autozone where they were about 50-55 dollars. A sensor connected to a cable with 4 loose wires and a few more parts which would complete the plug (which you build yourself).
My cables from my sensor lead up to a connector which had a perfect fitting plug on it...which was different that the new one though...so replacement in unavoidable.
I just can't get to the rest of the plug to fit the new connectors on. there is some sort of cover (metal, sharp edges) covering the cables. So, i am now off to remove such plate and get to the cable to place new connectors...
Don't do it yourself but pay a mechanic 40 bucks...that's what it's worth.
First guy was right, they just screw in and out. Go back to autozone or checkerauto and you can rent an "oxygen sensor" wrench/ratchet kit. (once you return the kit autozone will refund all your rent money). The kit comes with a dozen different sized and shaped sockets that will fit over your oxygen sensor to help pull them out easy. (my oxygen sensors were covered with dirt that I had to scrape off first, because I go off roading a lot). Make sure you buy the oxygen sensors that already come with the attachment clip for the wires (this will save you lots of time and frustrations) they're only a few dollars more. Before you screw the new oxygen sensor back into place, you should probably put some RTV sealant around the washer. You can get that at autozone too. It comes in a tube for a few dollars. Make sure you get the RTV sealant marked "sensor safe" or "wont harm oxygen sensors" and also that it has a high heat tolerance.
