Kia Optima

The drivetrain warranty of the 2013 Kia Optima is 10 yr./ 100000 mi..

1,4,5,2,6,3

jack up car, remove wheel, may need a pry bar, remove 2 bottom bolts at bottom of strut. go into trunk area & find top of strut mount and remove the 3 or 4 nuts securing the top. push down hub assembly & pry outward, pull strut down and out. installation is opposite of removal.

The LX on a Kia Optima stands for Luxury. The Kia Optima was first manufacured in 2000, and comes in EX, LX, and SX models. It is sold in Europe, Asia, and North America.

First you need to know what is wrong with it before you can fix it.

$65 -$210 depends on when your car was made. If it was manufactured before June 30th 2001, it will be cheaper than one for a car built after that date. Look on the inside of the driver's door frame for the date.

Make sure you have the Optima on a level surface with plenty of work room, and get your tools together beforehand. Jack, jackstands, metric sockets and a flathead screwdriver are just about all you need. 1. Disconnect the batt cable on the negative side of batt.

2. remove the speed meter and shift cable (only two wired connections to starter housing).

3. Verify all leads and power have been disconnected, then remove 2 bolts connecting starter to housing. Watch your head. Pull the starter straight away from the housing.

4. To install, do the reverse. THIS IS VERY IMPORTANT..MAKE SURE THE VERY FIRST THING YOU DO IF THIS IS YOUR FIRST STARTER IS DISCONNECT THE POWER (OPEN THE CIRCUIT) FROM THE BATTERY. If you accidentally jump the starter with a screwdriver or wrench you'll get a light show and bang your head.

4 cylinder 2.4 litters uses 10W40

The squealing could be that you need to add power steering fluid. Also you should check the belt that operates the power steering pump, if bad replace it. If the power steering pump is full and the belt is ok, then you may need to replace the power steering pump.

The 2008 Kia Optima has a 2.4 L base engine size.

It's in between the engine and airintake. Second one down, horizontal. The hose looks like it goes itno the lower part of the radiator.

Kermit

Thermostat should come with a neopreme seal around edge.

No The manual also states that I should remove the spark plugs is that necessary?

On a 2001 Kia Optima, the fuel pump is located inside the fuel tank. To access it, you typically need to remove the rear seat and the access panel, or in some cases, drop the fuel tank itself. It's essential to take safety precautions, as working with fuel systems can be hazardous. Always refer to a repair manual for detailed instructions before attempting any repairs.

The trouble code for a crankshaft position sensor on a 2005 Kia Optima is typically P0335, which indicates a malfunction in the crankshaft position sensor circuit. Other related codes may include P0336 and P0337, which correspond to performance issues and sensor range problems, respectively. If you encounter these codes, it's advisable to check the sensor and its wiring for faults or damage.

The EGR (Exhaust Gas Recirculation) valve on a 2002 Kia Optima is typically located on the engine's intake manifold, close to the throttle body. To access it, you may need to remove some components or hoses that obstruct your view. It's usually a small cylindrical or rectangular component with an electrical connector and vacuum lines attached. Always consult the vehicle's service manual for precise location details and procedures.

To remove the rear sunshade on a Kia Optima, first, ensure the vehicle is parked safely and the sunshade is fully retracted. Locate the mounting clips or screws that secure the sunshade to the rear deck or window frame. Carefully detach these fasteners, taking care not to damage the surrounding trim. Once released, gently pull the sunshade out from its housing.

To program a 2001 Kia Optima keyless remote, start by sitting in the driver's seat and closing all doors. Insert the key into the ignition and turn it to the "On" position without starting the engine, then turn it back to "Off" and remove it. Within 10 seconds, insert the key back into the ignition and turn it to "On" again, then press and hold the "Lock" button on the remote for about 5 seconds. Finally, turn the key back to "Off" to complete the programming process; the locks should cycle to confirm successful programming.

The 2013 KIA Optima typically uses semi-metallic brake pads, which provide good performance and durability. However, some models may also be equipped with ceramic brake pads, which offer quieter operation and less dust. It's important to check the specific trim and brake system of your vehicle for the exact type. Always consult the owner's manual or a professional for the best recommendation.

To reset the ECU on a 2012 Kia Optima, you can disconnect the negative battery terminal and leave it disconnected for about 10-15 minutes. This allows the ECU to clear any stored data and reset itself. After reconnecting the battery, you may need to drive the vehicle for a short period to allow the ECU to relearn its settings. Always consult your owner's manual for specific instructions related to your vehicle.

When you get new tires for your 2008 Kia Optima, it's not always necessary to replace the Tire Pressure Monitoring System (TPMS) valve. However, if the valves are old or damaged, it's a good idea to replace them to ensure proper functioning of the TPMS. Additionally, if the tire shop is replacing the tire sensors, they may recommend new valves as part of the service. Always consult with your technician for the best course of action.