0
Mercury Villager
The Villager was a minivan manufactured by Ford Motor Company from 1993 to 2002, and was a rebadged version of the Nissan Quest. Designed by Moray Callum, the Villager featured a five-speed automatic transmission and a front engine, front-wheel drive layout.
1,605 Questions
Why don't my 1994 mercury villager brake lights shut off with out disconnecting the battery?
Two plastic pads on the brake pedal which press on two switches on a bracket are missing. Meaning the switches never get pressed and the brake lights stay on and run down the battery. See a dealer to put new plastic "buttons" in the pedal.
Where is the knock sensor location on a 2001 mercury villager?
The knock sensor is in the engine V under the intake manifolds and coolant crossover pipe. As it requires considerable disassembly and an expensive new gasket set to reach it, I suggest you make very sure there is something wrong with it first. You will have to remove the upper and lower intake manifolds and coolant crossover pipe assembly to reach it. Just because you are receiving a trouble code for it does not mean there is anything wrong with it. This sensor shares a circuit with other components that often will set a "ghost" trouble code.
Can you use transmission fluid to unfreeze a car motor that seized up do to loss of oil?
Transmission fluid is just oil and will not unfreeze a seized engine.
Where can i find a 1994 Chevy truck exhaust system diagram?
go to your local parts store and order one or go to www.stylintrucks.com and look under exhaust
Is the 1998 neon DOHC 2.0 engine a non-interference engine?
The engine is an interference engine, if the timing belt breaks or slips it will cause damage to the valves and possibly the pistons.
What oil was 1996 Mercury Villager use?
5W-30 is the preferred oil ( according to the 1996 Mercury Villager Owner Guide )
the starter is bad and has an internal short
That answer is simplistic. On my '98, for months I could hit the starter and make it work. When I actually removed and disassembled the starter, one of the brushes was worn out. Hitting the starter moved it just enough to contact the commutator. Installed new brushes three years ago and haven't had any problems since.
How should I add coolant to a 1996 Mercury Villager?
Slowly to prevent an "air lock" through the top of radiator or through coolant recovery tank
How many gallons does the gas tank of a 1993 Mercury Villager hold?
20.0 gallons for Mercury Villagers '93-'98.
Where is the front heater blower motor on a 1996 Mercury Villager?
Remove the glove box. The front blower motor and the resistor can be accessed from there.
How do you repair a gear shift cable on a 95 Mercury Villager Van?
Can anyone tell me how to perhaps fixed a stretched cable until I can afford to put a new one in it? Do I have to make adjustments at both ends? I've attempted to take the steering column apart before, but it got very complicated. Also, is there an easy way to disable the air-bag (steering wheel mounted) while I work on the cable? Please help. Steven
I would suggest replacing the range switch, first of all, as well as the shifter cable if you think it is suspect, and perhaps the steering column and instrument cluster as well. It sound like you have multiple issues both at the transmission and in the column.
How do you fill up the rear window fluid on a 2000 Mercury Villager?
On a 2000 Mercury Villager :
The washer fluid for the rear liftgate is supplied by the same
reservoir as the windshield ( located in the engine compartment )
Do you have a picture of which direction a thermostat in a 1995 Mercury Villager goes?
No picture, but all thermostats go with the spring side towards the motor. On thermostats I changed, there were words on them and stated which side goes up
Where is the maf sensor in a 2001 mercury villager sport?
In the tube between the air filter box and the rubber intake boot.
no
When do you have to reset the fuel pump on a 2001 Mercury Villager?
The fuel pump does not normally have to be "reset". If the vehicle is in a crash that causes the inertia switch to trip, the switch will have to be reset before the fuel pump will run.
Where is the ac orifice tube located on a 1994 mercury villager van with a 3.0 liter engine?
On line coming out (near bottom) near the cannister by heater box, - (the thingy that always was sweating while a/c was working)! Is about 3 inches from heater " box" at firewall (called a plenum)!! There are 2 lines about 3/8 inch in diameter tied together with metal piece with a screw thorugh it holding it together! Come back toward front of engine about 6-8 inches, and you will see fittings there (2 different sizes 11/16 and 7/8 as I remember)! Hold these fittings securely to prevent bending tubing, _ -- you will see that the one going towards firewall has a "reduction in size"--the orfice and "finger screen" are in there! This is located on the"high pressure" line, (smaller line coming from the compressor). Of course you have to evacuate the system, -- and it is sometimes hard to remove screen from the tube- use anything that you can hold on (possibly a hook)-and pull out --if needle nose pliers aren't able to pull it out.
How do you set timing on 99 mercury villager after timing belt breaks?
You match the timing marks on the sprockets with the marks on the belt...exactly.
Where is location of speed sensor on 2000 Mercury Villager?
The speed sensor on a 2000 Mercury Village is found on the transmission of the vehicle. The sensor will be placed on top of the unit to read the rotations of the transaxle.
How many Ignition coils are there on a 1999 mercury 3.3 liter v6?
Only one. Located on the right side of the engine next to the distributor.
What does a bad knock sensor to to the engine if not replced?
Nothing. The knock sensor is probably NOT faulty. The knock sensor is in the engine V under the intake manifolds and coolant crossover pipe. As it requires considerable disassembly and an expensive new gasket set to reach it, I suggest you make very sure there is something wrong with it first. You will have to remove the upper and lower intake manifolds and coolant crossover pipe assembly to reach it. Just because you are receiving a trouble code for it does not mean there is anything wrong with it. This sensor shares a circuit with other components that often will set a "ghost" trouble code.
Read more: How_do_you_replace_the_knock_sensor_on_a_1999_mercury_villager
What is the wheel torque setting for a 1999 mercury villager?
Hardware Size Torque 10MM 45-55 Ft. Lbs. 12MM 80-100 Ft. Lbs. 14MM 110-140 Ft. Lbs. 7/16" 70-80 Ft. Lbs. 1/2" 80-100 Ft. Lbs. 9/16" 135-145 Ft. Lbs. These are general torque specs and may be different for nuts on aluminum wheels.
How do you set the clock in a 2000 mercury villiger?
Just press the hour and minute buttons on the radio.
When do you change the timing belt on a 1997 Mercury Villager?
Recommended interval is 105,000 miles..
What is the firing order on 93 mercury villager?
The firing order is 1-2-3-4-5-6. Rotor turns counterclockwise.
