0
Toyota Highlander
Also known as the Toyota Kluger in Australia and Japan, the Toyota Highlander is a 4-door, midsize crossover sport utility vehicle (SUV) produced by the Japanese auto builder Toyota Motor Corporation since 2000.
1,728 Questions
Are you out there trying to find the best hybrid vehicles up for purchase? If so, there are a few designs you should consider. The Ford Escape Hybrid will cost you around $30,000 and is a great deal. The Toyota Highlander Hybrid is another popular hybrid car of choice. This hybrid is a bit more expensive and will cost you around $40,000. It is more powerful than the Ford hybrid though.
What octane of fuel does the 2003 Toyota Highlander use?
For gasoline- engine models destined for use on the North American continent, 87 Octane.
Can you disable the power tailgate on a 2008 Toyota Highlander?
Can't figure out how to delete a question. Switch in glove box.
How can you repair a temperature control knob that will only turn halfway in a '92 Honda Accord?
Hi there, You proboly don't have to change the knob itself, if you look at the side of the heating duct itself by the floor you'll probobly see something obstruting the movement of the door, what you will see is a half wheel with a small steel cable make sure that the wheel isn't hitting anything
What is the gas mileage on a 2009 suburu forester?
If you are looking to purchase one, you could look at the sticker on the window. Of course those never have been a guarantee and my '00 Forester has never gotten that high number while I have owned it. Fuel mileage ratings for all vehicles are provided by Uncle Sam at this Web site. Talked me out of buying the Range Rover: http://www.fueleconomy.gov/feg/findacar.htm
Where are the spark plugs on a 2001 Toyota Highlander?
The 3.0L 1MZ-FE Engine, California, Highlander Limited V-6 Like many Japanese cars, they are screwed into the top of each cylinder head. The 3 spark plugs closest to the front of the car are recessed deep through the valve cover, so you must first remove the flimsy plastic engine cover (held in with Allen head nuts), and remove the three (3) DIS (Distributor-less Ignition System) Spark Plug Connectors from the Valve Cover. The DIS Spark Plug Connectors are each held in place with a single 6mm bolt (so they don't come loose). If you look down the "Tube", you will see the top of the spark plug. The other three spark plugs are in the rear side valve cover and have the same DIS Spark Plug Connectors and bolts. Unfortunately, the Upper Intake Plenum and Throttle Body must be removed if you need to get to these spark plugs. Also, to remove the Upper Intake Plenum and Throttle Body, the Strut Tower Brace has to to be removed to give you enough room to work.
What MPG does the Toyota Highlander get?
The Toyota Highlander averages about 28 miles per galllon but differs depending on state and year it was made in because there are 195 different Toyota Highlanders.
How do you reset the maintenance required light on a 1988 dodge van?
should be able to remove the + side of the battery cable for 10 min then put in back on. that should shut it off , if it comes back on then something else is wrong. first be sure to check all the fluids oil, water, brake,power steering and even windshield washer fluid. they all have low level censors in them
What is the maximum towing capacity of the 2014 Toyota Highlander-Hybrid?
The maximum tosing capacity of the 2014 Toyota Highlander-Hybrid is 3500 lbs..
Do you have to remove the motor to change the timing belt of a 2000 sunfire?
First off, you do not have to remove the engine from any vehicle I know of to replace a timing belt. Secondly, your vehicle has a chain, and not a belt.
How many miles should a 98 BMW 528i have?
I know this is not your question, but I bought a 2000 528i with 68K miles in almost perfect condition. So with a 1998 I really would not but anything with more than 90K miles...
Air filter on 2005 Toyota Highlander. where is it and is there only one?
If you're asking about the engine air filter, it is located enclosed in a black plastic box slightly to the right hand side of the engine compartment (as viewed from the front grille area).
There is another filter, but it is the cabin air filterfor the heating and A/C air entering the passenger compartment. THAT is located behind the glove box assembly.
How do you adjust headlights on 2008 Toyota Highlander?
its super duper easy you can see the adjustment bold under neath the buld holder .. all you have to do is tight it up
How do you replace tail light on 2002 silverado?
open your tailgate. there are two Phillips head screws along the side of the bed that hold the tail lite housing in place. remove those and you can pull the whole housing out giving you access to the bulbs. pull the harness off and twist out the bulb in question.
Why won't a 1994 Mercedes e320 go into gear eventhough the shifter moves into position easily?
Bad transmission?
Linkage or cable control out of adjustment?
How tall is the 2009 Toyota Highlander?
The height of the 2009 Toyota Highlander is 5 ft. 8.1 in. (68.1 in.).
What type of oil goes in a 2005 Toyota Highlander?
It can depend on whether or not your area is subject to extreme heat or cold conditions but the usually recommended oil is SAE 10W-30.
How wide is the 2014 Toyota Highlander?
The 2014 Toyota Highlander is 6 ft. 3.8 in. (75.8 in.)1 one-touch power windows wide.
What is the gross vehicle weight of the 2003 Toyota Highlander?
The gross weight of the 2003 Toyota Highlander is 4985 lbs..
Engine check light on 2002 Toyota Highlander?
Have vehicle scanned to determine the problem - usually in the emission control system,
Where is the transmission located on a 1990 Mazda 323 and how do you change?
Regardless of whether it's a manual or autoamtic, the transaxle (transmission plus final drive) is located on the left side (as you look forward) of the engine. Unless you have the right tools including an engine hoist or transmission jack, jack stands, and floor jack, it's not a job you want to take on. I assume you are replacing the transaxle with a rebuld or new unit. Plan a whole weekend to do this job.
Disconnect the battery, speedometer cable, clutch cable, gear selectro linkage reverse/neutral switch wiring, jack up car, support on stands, remove road wheels, drop the lower control arm bolts, remove the half-shaft nuts, remove the half-shafts (make certain you have a drain pan under the transaxle); remove the starter motor, support the engine, remove the bolts holding the transaxle to the engine, support the transaxle with a floor jack, remove the four bolts that attach the cross-member to the body, pull the transaxle away from the engine and lower the transaxle/crossmember assembly on the floor jack. Dettach the crossmemebr from the transaxle.
When reassembling, make certain all componets, wiring etc are clean; if manual transaxle inspect clutch & flywheel replace if needed, re-surface flywheel if needed. Once reassembled, fill transaxle with new fluid per manufacturer's recommedation; retorque all bolts per shop manual.
Good luck
Malcolm
How do change a timing belt on a 1996 escort?
We really need to know which of the three possible engines you have, but here is a rough outline:If you have a 1.9 or a 2.0 SPI engine (not a 2.0 ZETEc)Jack up the RF corner of the vehicle and remove the RF wheel. Remove the front motor mount located on the rightfender apron and support the engine by the oil pan using a floor jack with a block of wood(You will now be able to jackthe engine up and down as you need to). Remove the serpentine belt and if there is a belt tensioner in the way of the timing cover, remove it too. Remove the crankshaft pulley and remove the timing cover. Remove the old belt, and it is recommended that you replace the water pump at this time as well. Line up the crankshft timing mark(the keyway will be pointing straight up), and line up the camshaft timing mark(an arrow cut into one of thewindows of the gear lines up witha dot on the cylinder head). Install the new belt onto the timing gears. Set the tensioner in place. Turn the engine over two complete rotations of the crankshaft, and then recheck the timing marks for correct alignment. (a little fussing getting the crank back in position is normal.) Getting the marks lined up right here saves a lot of do-over work!. Reasemble the cover, serpenting belt etc. in the reverse order as disassembly.
A 2.0 ZETEC engine requires special tools as there are no timing marks of woodruff keys for the camshafts.The valve cover has to come off, and a special alignment tool used to line up the cams.The crankshaft is lined up using a special tool inserted into the engine block through a holethat is exposed when a plug is removed.
AnswerIt can be difficult even with a strapwrench to get that damper pulley bolt tight during reassembly; without an impact tool. Be sure to use a dab of red locktite on the threads. I almost lost my damper and if the slot for the damper key on the crankshaft were damaged it would've necessitated replacement of the crankshaft!!! By design luckly (damper metal softer than key & crankshaft), all that was damaged was the damper... it was replaced.