0
Toyota Sequoia
The Sequoia is a full-size sport utility vehicle (SUV) manufactured by Toyota Motor Corporation from 2000 to the present. This model is sold exclusively in the Middle East, the US, Puerto Rico, Mexico, Chile and Canada.
1,008 Questions
Does a 1988 Chevrolet S10 with a 4 cylinder have a timing belt or a timing chain?
It has a Timing Chain.
Where is the oxygen sensor located on 2003 Toyota Sequoia?
There are 2 oxygen sensors - one pre-cat and one post catyltic convertor. They are on the passenger side, in the manifold. Be sure to check the trouble code to identify which one might be defective.
What is the price for manual Toyota Sequoia?
Toyota never made a manual version of the Toyota Sequoia.
How wide is the 2014 Toyota Sequoia?
The 2014 Toyota Sequoia is 6 ft. 7.9 in. (79.9 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.
When do struts on a Toyota Sequoia need to be changed?
The struts need to be changed every other year.
How do you preset radio stations on a 1988 buick lesabre?
If I remember correctly, those models may be old-style 'push-button' type radios? If so, do the following:
1) Select the 'station' or frequency you want to store as a pre-set by turning the right (tuning) knob.
- In older models, FM or AM doesn't matter, as the button is only "remembering" a position on the dial.
- In newer (but still push-button or 'old-style') models, the button will also switch between FM and AM, but each button remembers BOTH the band AND the frequency, but will not remember more than one station (I.e. The button wouldn't remember one station for FM and a different one for AM) on the same button -- except of course, if those two stations happened to be exactly the same linear position on the dial.
2) Pull the 'push-button' mechanism out towards you all the way (one click, usually) -- it may take a little more effort than you think or you way need to lift up slightly on the push-button to get it to move, especially if it's been a couple of decades.
3) Push the 'push-button' back in all the way -- the linear mechanism on the dial should not move at this point.
4) Test your new pre-set by moving the dial to the left or right using the right-hand (tuning) knob then pushing the same 'push-button' in. The linear mechanism -- if working properly -- should now move the dial to your new location and change the frequency to your chosen 'station'.
On new (digital) radios in cars & trucks, of course,with the radio on you tune in the band and frequency (and in some cases a 'bank' of presets [such as 'FM1', 'FM2', 'XM1' / 'SAT1', or 'AM1']) that you want to store then push 'set' then push the preset number you've chosen OR push-and-hold the chosen pre-set button (generally the radio will beep and / or flash the display and / or audibly re-tune the station once the setting has been stored) with the 'push-and-hold' method it may take up to three seconds in some cases for the setting to 'take'.
If you're having issues, hold the button in a bit longer until you get some sort of reaction from your radio and / or watch the radio's display to see if there is a message or prompt, as in many cases the radio may ask you if you REALLY want to change an existing preset, or the radio may need more information such as the 'bank' [again, meaning something like 'FM1', 'FM2', 'XM1' / 'SAT1', or 'AM1']in which you want to store the preset. Hope that helps!
AnswerShould just be able to select desired station and hold button for 3-5 seconds until blinks AnswerShould just be able to select desired station and hold button for 3-5 seconds until blinksHow do you program a keyless remote for a 2005 Toyota Camry?
This works on 2004 Toyota Camry as well.
Start with the key out of the ignition. Open the driver door (all other doors are closed). Driver door is unlocked (other doors don't matter).
Perform these steps within 5 seconds
Insert the key into the ignition (don't turn it) Pull key out
Insert the key into the ignition (don't turn it) Pull key out
Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition (don't turn it) and pull it out.
Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition and leave in the ignition.
Close the drivers door
Turn the ignition to ON (as far as you can go without cranking the engine), then back to off .
Remove the key from the ignition.
Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
Perform these steps within 40 seconds
Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.
Open drivers door
How do you reset the maintenance required light in a Toyota Sequoia?
Reset the system by the following procedure: 1. Turn the ignition key to the "ACC" or
"LOCK" position with the odometer reading showing. 2. Turn the ignition key to the "ON" position while holding down the trip meter reset knob. Hold down the knob for at least 5 seconds. The odometer indicates "000000" and the light goes off. If the system fails to reset, the light will continue flashing.
How do you open the door to the fuel tank on a 1980 Mercedes 300?
The fuel door lock is controlled by a vacuum valve (as are the doors locks and many other components on these models). If the car is unlocked, you should be able to open the door easily with you fingers. If the car is unlocked and the door will not open, the valve has failed and needs to be replaced. If you open the trunk of the car and look on the right hand wall of the trunk, you will see a little "door" right behind where the fuel door is. Remove this door and there is a manual release for the door. Hope this helps!
How many gallons does the gas tank in the 2007 Toyota Sequoia hold?
The gas tank on the 2007 Toyota Sequoia holds 26.4 gal..
Where is the oil drain plug on a Toyota Sequoia?
You have to remove the skid plate, then you can change the oil and filter
What is the best engine oil for a Toyota Sequoia?
I use the Mobil 1 Synthetic Oil extended life. It can go 15,000 miles. But I change it at 10,000 because of the filter might be getting plugged up. Do it myself because of cost but even if you go to a place ask for it. Then you don't have to go to as often. Also, my mechanic told me that synthetic keeps your car engine cleaner as other regular motors oil will gunk up over time if you don't change them every 3000 miles.
How many horsepower does the engine in the 2005 Toyota Sequoia have?
The 2005 Toyota Sequoia's engine produces 282 hp @ 5400 rpm.
How many qts of oil to fill 2007 sequoia?
A 2007 Toyota Sequoia will hold approximately 6.5 quarts oil. The recommended type of oil needed is 10 W 30.
How wide is the 2004 Toyota Sequoia?
The 2004 Toyota Sequoia is 6 ft. 4.4 in. (76.4 in.)12V front, 12V rear and 12V cargo area power outlet(s) wide.
What are the instructions for replacing a starter in a 1992 Isuzu Trooper?
Remove the positive battery cable first. The starter is on the passenger side of the engine. Might be easier to get to from below. Remove the bolts holding the wiring to it than the bolts that mount the starter in place. Be careful if it has shims that you make sure you put them back in the same way. (These are little thin spacers that go between the mounting surface and the starter). Installation is reverse. Probably would take you no more than 30 minutes to do it all.
What is the maximum towing capacity of the 2014 Toyota Sequoia?
The maximum tosing capacity of the 2014 Toyota Sequoia is 7400 lbs..
