Bumpers

The rear bumper cover is held onto the frame by 4 bolts. They have a 13 mm head, and are accessed from under the van. They thread directly into the back of the bumper cover, therefore no nuts to worry about. The rounded edges of the bumper cover slide over a pin, so when the 4 bolts are removed, the bumper cover can be pulled straight off.

Remove the plastic trim on the seat tracks. That will expose the four nuts that hold it in place. Remove the nuts. Disconnect the electrical connector. Remove the seat.

Rick

I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogspot.com

You will have the large bolts and nuts that mount it to the frame. Those are simple a easily found. However, there are also two small nuts on each side. On the rear they hold the bumper end to the quarter panel. On the front, they mount it to the fender. They are a little difficult to get to, but they do have to come out.

4 13mm bolts, 2 clips. remove licence plate, 2 bolts there, remove plugs near steps, 2 bolts there. slide ends off clips.

No.

No.

Haynes repair manual, Dodge Neon 2000 thru 2003. Book #30036

To remove the front bumper remove the following: 12 plastic clips, 6 accessuble on the top, 6 accessible on the bottom 6 screws on the bottom. Bumper hangs on a series of hooks (6) just beneath the headlights.

i dont know im stupid

A thick cloud of tiny water droplets suspended in the atmosphere at or near the earth's surface that obscures or restricts visibility (to a greater extent than mist; strictly, reducing visibility to below 1 km) It is the formation of a cloud at ground level. It is condensation in the air.

max and Harold stoeher

They were oiginally made for Blueys ute world. but now due to bad publicity and road legislations, they are no longer made

Remove 2 screws securing each wheel arch liner and 2 screws behind each liner, 6 screws along top edge, 2 plastic nuts on bottom edge. Good luck, spradders.

yes

1.Apply parking brake raise vehicle and support it 2.Disconnect the negative battery cable and then the positive cable and wait two minutes before proceeding any more 3.Remove the retaining screws securing .the air deflector and the upper side of the bumper. 4.Remove the turn signal light housings 5.Detach the screws securing lower side of the bumper cover 6.Once the cover is removed,remove the retaining bolts or nuts and detach the bumper assembly.The bumper is retained by teo bolts at each end.

I don't much about cars. SORRY!!!!!!!! Bootscootn-00-04 eclipses' have the same parts. What you can do is search online for part numbers for an eclipse. If the 03 eclipse part number matches the 00 part number then there will be no issues. I have bastardized my 00 eclipse with several different pieces.

Bumper stickers can be made at your local sign and decal shop.

Large volume orders would probably best be served by a business that specialises in them

yes

there is 4 screw on the top near radiator support. 2 screws per side on the side of the bumper near the fender wells. and 3 under the car by the motor.

10mm

yes its the same bumper alignment, all the parts from 1988-1991 are second Gen Parts for the CRX there for all the parts from those years fit each other.

First, you need to access the side panels from the trunk. There are two screws on each side. You will need to remove the jack holder to reach one of the screws. Then you will need to remove the rear light assemblies. Once you have pulled those off, you'll find a couple friction fittings underneath, pull those out. Just to the sides of the light, inside the trunk, there is a nut angle upward in the corner, kind of hard to spot if you're not looking for it. Remove one from each side. Then you only have a three screws around the outside of the bumper on each side, and two more friction fittings on the bottom rear of the bumper. Now the bumper should easily come off, just be careful to disconnect side parking lights as you remove the cover.

I tow my boat with a tongue weight of about 140 pounds and a tow weight of 1500 pounds and the truch handles ok but the bumper has started to sag at the hitch

Hello, Would start by replacing the Bumper Bracket holding the bumper on. If the hosing is smashed that the bracket is bolted onto you will need to take it to

shop to have repaired. Below is a link to the cost of one bracket to give you a idea of the cost. Good luck http://www2.partstrain.com/store/?N=11371+1684+4294967270+9335

a mother or father, they are talking about they're child