0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
How do you stop water leakage into interior on a 1995 beretta after it rains?
its usually the ruber seal above the door u need to take the seal off inspect for tears or rips if looks ok sceaz the iner metal rib all the way along frome one end two the other glue with weather strip adhesive and replace the moldeing this should fix the problem.
Where can you find PCV valve on 1996 Chevy Beretta?
if it's the 3100 V6, it is on the right side of the front valve cover
How do you change dashboard lights on a 1996 beretta?
If you mean the instrument cluster, it's actually kind of a pain in the butt.
You need a Phillips screw driver, flat head screw driver, and a 1/4" ratchet driver or Torx T6 driver.
1) Start by looking under the headlight switch, you'll see two screws. Remove those.
2) Now look under the wiper control switch, remove those two screws.
3) If your Beretta has a tilting steering wheel, move it as far down as you can.
4) Now this is the tricky part, because it doesn't seem like it's the right thing to do, but this is how you do it. Grab the curved plastic over instrument cluster and pull. You'll hear creaking sounds, then it will come loose, starting near the windshield then will come off.
5) Disconnect the headlight wiring harness
6) Disconnect the wiper wiring harness.
7) There should be 4 black screws along the white outer shell of the instrument cluster. Top Right, Top Left, Bottom Right and Bottom Left. Check all the way around because there may be two on top of the steering column as well. Use either the Torx or ratchet to remove all the screws.
8) Gently pull the instrument cluster out, and flip it over. You'll see a greenish/brown circuit board with white or black thumb screws. Those are the lights. Just turn the ones that are burnt and pull them out, pull the bulb out and replace.
Once you have all the lights replaced that are burnt out, just repeat the steps in reverse.
Why is water leaking on the driver side floor in a 1989 beretta?
your beretta has a leak!
It comes into the air ducts right below the windshield! Wonderful of Chevy to do this to you, but after about ten years, the vents will warp and allow water to drip into the compartment below the dash.
No worries - you won't have electrical failure. If you live in a rainy climate, you'll have at least 2 inches of water build-up in either the front or back floor area.
Choice number 1. Purchase a Wet/Dry Vacuum Cleaner.
Choice number 2. Fix the Chevy screw-up!
You must build (from scratch) a shield on top of the air intake for the heater, below the windshield. Don't ask me where to buy one, but I made one out of long sheets of durable plastic, (I'm a handyman) and screwed them into place.) They must be angled towards the front of the car, so rain can run off, and into the engine compartment, but not into the air intake vents.
Then, buy a new car and stay clear of Beretta. I had one for 16 years, (INDY) and it was hard to part with, but you MUST DO IT!
Buy an older Toyota MR2, you'll be glad you did.
How much horsepower does a 1991 3.1 v6 automatic have?
It depends on the condition of the engine, and how well its been maintained. A stock 1991 3.1L MPFI V6 was rated at 140hp, but private dynos over the years have show numbers as high as 152hp, depending on the make/model/condition of the vehicle. Several factors are attributed to hp loss/gain.
What is firing sequence of the wires on a 95 2.2 beretta?
Your firing sequence is 1-3-4-2. looking straight at engine from front of car, your plugs are L-R 1-2-3-4
Yes it is a direct fit. Although it is best to refer to the engines as 3100 and 3400, respectively, so as not to confuse them with 3.1L MPFI (1990-1994) and 3.4L. They are all different engines.
On a 3.1L V6, it is located on the passenger side of the engine, towards the front. There is a smooth, shiny metal pulley over the top of it. To remove/replace it, you will need to loosen the tension on the belt by raising the belt tensioner pulley, located on the bottom directly below the alternator. Once loose, slip the belt up over the alternator pulley, and lower the tensioner. Remove the 4 bolts holding the pulley onto the water pump. To prevent the pulley from turning, slip a large flathead screwdriver (or tire iron) into the hole in the motor mount directly above the water pump pulley. This will bind against the bolts as you make your way around. Be sure to loosen all bolts first before completely removing them. Once they're all loose, you can remove them by hand, and slip the pulley off the water pump. There are 5 small bolts holding the water pump to the engine. They are spaced around the outside ccircumference of the water pump. Once all 5 are removed, the water pump should come out. If not, tap on it lightly with a rubber mallet. Sometimes the gasket sealent likes to stick. Once removed, be sure to scrape all traces of the old gasket material, and clean the surface with acetone. Installation is the reverse or removal. Check for lost coolant, and add more if needed to the proper level. Start the engine and allow it to reach opearting temperature. Check for leaks. None? You're done!
if its a rotten egg smell its probably the cat if its loud volume look for a blown gasket or a hole in the pipes
What is the electronic box on my 1988 Chevy truck's brake master cylinder?
i was told it is the anti lock brake system And you were told wright.
What does the differential look like?
You can not see it, it is part of the transmission assembly. Unless it is a rear wheel drive car.
The high beams on your 95 beretta wont turn off?
1995 berettas and corsicas have generic daytime running lights no matter what if the switch is on your headlights will be on. (although it should be lowbeams). in 1995 Chevy didn't use a lower wattage for the daytime running lights. and so far i haven't found a way to by-pass them.
Where is the fuel reset button for a 89 Beretta?
there is no fuel reset button . there is a fuse in engine compartment against the fire wall in the center next to relays with a plastic water proof cover over it possible under the plastic dress up cover that covers the harness (if it wasnt already removed and tossed away )
min means Minute Min can also mean Minute meaning small. Another meaning can be minimum. The lowest amount of something.
Need to be more specific. Beretta makes a whole line of handguns, rifles, and shotguns, and the price range varies greatly between models.
How do you get the drum off 96 Chevy beretta to change rear brake shoes?
Make to chock the front tires and leave the emergency brake off. Jack the vehicle and remove the wheel. The drum is only held on by being squeezed between the hub and the tire, so when new they just slide right off. However, if you live in the rust belt you will have to beat the hell out of it with a hammer. First, get some good penetrating fluid like "PB Blaster" or "Liquid Wrench" and soak the area around the center hub and lugs. Second, try gently gently tapping on the studs (bolts) but be careful not to miss or you will bugger up the threads. If it still wont come off get a bigger hammer and hit it from the back, being careful not the damage too much while swinging away. Continue rotating the drum while beating on it so as to remove it evenly so it doesn't get wedged.
Your 1989 Beretta will not start it turns over and the lights all work fine?
Could be many things. This model year had weak coil packs. You might want to check that.
Answerit is possible that the fuel pump is not working or you have some bad gas that's the best i can dowolverine
AnswerTurn the key forward without turning the car on and listen for the fuel pump to "buzz" (Best if you have the door open with your foot pushing to door open/ajar switch so you don't hear the continuous "PING, PING" of the door.) If you hear the pump, pull a spark plug, reattach it to the plug wire, rest it somewhere in the engine (JUST DON'T HOLD IT IN YOUR HAND!!!) and have someone try to start the car. If you don't see a spark at the plug, spent $18 and purchase a crank sensor. More then likely your problem. AnswerI would say one of two things the coil packs ,but it is unlikley that all coil packs go bad at once,so the one I would try is the icm ignition control modual,get one from the junk yard first instead of spending a lot on new if its not it. AnswerI had the same problem. Turned out I needed to replace the coil packs and the ignition sensor.Had those replaced and the car fired right up on the first turn. Answertry a new computer id get one from the bone yard that u no is good AnswerI would try getting a code key from autozone and checking the code book for the code it gave you. I would also trie the ignition module or the computer.How do you change the torque converter lock up clutch on a 1991 beretta?
If you have a torque converter lock all the time problem when hot
replace solenoid under driver side cover of transmission .
Where is the PCV valve located on a 1992 Chevy Beretta?
The PCV valve is located on the backside valve cover, its towards the drivers side of the valve cover, tough to get at not much room, just changed mine.
I want the doors to lock automatically.?
Some Models have Fuse that controls that ....I dis-connected mine after I locked myself out in car wash
Why might the cooling fan not be working on a 1990 Buick Skylark 2.5 engine?
I had the same problem with my 90 buick century, Replacing the temperature sensor did the trick, it is located above and behind the water pump.
How do you disassemble Beretta 390?
To disassemble a Beretta 390 shotgun, first ensure the firearm is unloaded. Begin by removing the forend; press the release button located on the underside of the receiver while sliding the forend forward. Next, open the action and remove the barrel by pushing the barrel release button and sliding the barrel forward from the receiver. Finally, you can access the internal components by removing the trigger assembly and bolt, if necessary, following the specific steps outlined in the owner's manual. Always refer to the manual for detailed guidance and safety precautions.
Where's the flash fuse located on a 91 beretta?
under the steering column, between steering and fuse panel. you have to take the plastic off and just feel around for it. its usually a little siver round canister
