Chevy Corvette

Http://www.autozone.com go here on the right side there is link called repair info... go there... click on your year and model the click on engine components it will give you a detailed description along with pictures... hope this helps

BSM Or body side mouldings.Some people don't like the mouldings on the cars so they remove them.

You have to slip in a slimJim and grab the latch hook and pull straight down while putting downward pressure on the hood. If you don't know what a slimJim is look it up. I would also encourage you to lalso ook up the hood latch part for your car so that you can see how the latch hook catches the lower latch cup.

Lower rear end of the engine On the passenger's side lower rear of engine.

Their is a small staple in the front of the knob you pull it out with a small screw driver and it should pull right out hope it helped

the 1990 corvette had the LT-1 motor 300bhp and 340fpt that is the correct answer to this question!

Yes, it is a two-piece (left - Right) air dam that significantly reduces engine heat.

There are several hidden VIN locations depending on the type of vehicle. Some have a hidden VIN embedded in the computer of the vehicle as well as on the frame.

There are about 3 reasons your lights don't display at night. 1. Ground wire is loose, located on firewall. 2. Burned out LED display, must be replaced. 3.

Yes, but the Dodge Viper SRT10 ACR is better compared to the Chevrolet Corvette ZR1. The Viper SRT10 ACR beats the Corvette ZR1 at the Green Hell.

Huh! I see no evidence, proof, or facts backing that statement up. Go compare the same year Corvette and Viper, Don't look at things used to dress it up (paint, cool words) look at the technology. The Viper is a dumptruck.

No need. The speakers come out the top of the dash.

Between $200,000 and $300,000 depending on the condition and the original sticker price is $3,498.

they say there about 115,000 to 125,000

It is required with some engines.

C5 has a very large trunk area.

The 2001 Chevrolet Corvette is 6 ft. 1.6 in. (73.6 in.)12V front power outlet(s) wide.

You need to remove the intake manifold. There are two sensors one in the front and one in the rear. I would replace them both. It is recommended that you put a dam of RTV silicone 3/4 around location and leave the back portion open to let water drain out. The silicone does not go on the cover of the knock sensor but on the valley pan approx 1/8 in front of it.

look at the pictures of this guys vette and ask him which ones hes using. They are definitely c5 zo6 on his '88.

good luck

http://www.digitalcorvettes.com/forums/showthread.php?t=114661

tjeck radio cornektions roomlamp- generator

-

It's relatively simple, however you need a thin wrist. 1. Dislodge the front brake air duct. 2. Reach in the front brake duct and follow wiring to the parking light housing assembly. 3. There's clip on the bulb housing that needs pressure applied, then gently rotate the bulb. 4. Simply remove and replace bulb. That will save about $40 to $50. If your wrist is too big, there's an alternate method: 1. Manually open the headlight (there's a round rubber cover over the control). 2. Remove the plastic headlight wrapper (3 screws). 3. Reach in through the opening to get to the light housing assembly and follow steps 3 and 4 above.

It is behind the drivers seat under a small door on the back deck. It is probably side post.

Follow the link : www.club348.com/technical/Tech/348.html

pull on the 2 wires with vice grips then get a new lever and wire cables before it costs a bunch to get it open

I had this happen and the wire snapped and had to DRILL out the hold down pin (You Don't want to have to do that I KNOW)

oil servis reset without using a computer http://www.kofla.net/chevrolet.htm

all corvettes run a 5x120.7 bolt pattern 68-82 used a 7/16 stud Low offset 84-89 12mm stud Med offset 90-current 12mm stud High offset