answersLogoWhite

0

🚗

Chevy Impala

Launched in 1958, Chevy Impala is a full-size vehicle built by General Motor’s Chevrolet division. It is Chevrolet’s most expensive vehicle and US best selling automobile through 1965. It is distinguished by its triple symmetrical taillights.

4,997 Questions

How do you change a headlight assembly on a 2002 Chevy impala?

Open the hood & look for two white sliding clips. Pull them up to remove them. The headlight assembly should easily pull out. Identify the wiring harness & unclip it. Reverse the procedure to reinstall

How do you disable passenger side airbag in a 2005 Impala coupe?

Unless the particular car has provisions for doing this and instructions on "how to", this should not be attempted by the home garage mechanic. There are many many sensors and electronics that control the air bags. To attempt a disconnect of one airbag, may cause irreparable damage to the other existing airbags, and reduce the effectivity of those, causing more injury and/or death to the driver.

Price to Replace oil pan gasket on 2001 Monte Carlo Chevy?

Alot! I did it for a client and charged $50 thinking it was a easy access pan. WRONG! It requires dropping the sub-frame from under the car while supporting the engie from up top. The bottom mount suppport its a real bear to put back on. I had my bro help me by pushing on the back of the bolt while I turned it. Other wise the bolt between the enging and the axle housing would of been left out. It took me from 8pm to 5am so, I suspect it would be 6 hours labor at a shop x $80 per hour plus parts. I left the oil pick gaske alone since the torx hole was filled with carbon. You will need 4 jacks stands (2) 2x4 pieces of wood and a chaing to supporth the engine. Set of extra hands at some point. A ratcheting box end, flex head 15mm wrench would help on that mount too.

Where is the antifreeze drain plug on a Dodge 360 engine?

You Should Find It Depending On Year Of Vehicle, Im The Bottom Of Radiator On The Passenger Side.

Changed steering shaft on 2002 impala now airbag light is on how does it reset?

If steering wheeel was turned to far, you may have snapped clockspring AIRBAG wire that runs through the steering wheel. Think of it as the same way a tape measure recoils after letting loose. If wheel was turned more than 2 complete revolutions from center, than it is more than likely a snapped wire.

Where is cabin air filter on 2002 Impala?

It's located under the cowl on the passenger side of the Impala.

How do you remove the door panels in your 1999 Z24 Cavalier?

To remove the door panel on a cavalier there are four screws on the under side and the back of the bottem lip. Remove those screws then there are 2 screw in the door handle. Remove those. remove the triangle piece of plastic where the mirror controls are then give it a little tug and the door panel should pop loose then lift up and walk away with it. If you have crank windows then you have to remove the crank lever and if you have electric locks the you have a clip you have to un do that powers the switch.

What is wrong if a 93 Ford Taurus oil pump light is on all the time after it ran low on oil and does not go out after overfill?

No the oil pump does not need to be primed. In most cases, this is caused by debris plugging the oil filter or the oil pressure sending unit. The first step is to do a complete oil change. If this does not fix the problem, then locate the oil pressure sending unit, remove it, clean it and make sure that there is nothing visable inside its mounting hole. Try reinstalling it and test again. If it still does not fix the problem, replace it and make sure the wiring harness is pluged in and tight. Good luck.

How do you reset the oil change light on a 2008 Chevrolet Impala?

See {How to Reset the Engine Oil Life System} on page 5-21 of your "Owner's Manual", under Section 5: Service and Appearance Care.....

How do you turn out the overhead dome light in a 2006 Chevy Impala?

Answer

Check door switches Check headlight switch this model works in opposite direction than most--twist counter-clock wise to shut off

If you have really strange things happing with your interior lights its probably your body control module. Example interior lights coming on when they shouldn't or going off when they shouldn't

How do you clean the wheel speed sensors on a 2001 Chevy Impala?

the wheel speed sensor is all part of the wheel bearing hub assembly you cannot clean them you have to replace the hub assembly its not that hard of a job gm cars are known for this problem.

Where can one find information on a 1969 Chevy Impala?

You can go to the website named 1969chevy that has special focus on that particular car and have any information you could possibly need about it. You can also go to blogs and forums where Chevy Impala enthusiasts are happy to answer any question you have.

How much is an original Impala 67 worth?

Chevrolet Impalas can range anywhere from $1000 to $25000. The prices depend on the condition of the car, the specifications of the car and the seller.

Where is the antenna on 2003 Chevy Impala?

It is tied in with the rear window defrost grid.

What size motor is in the 2008 Chevrolet Impala?

The typical 2008 Chevrolet impala without all the bells and whistles put into it usually runs a 348 cubic-inch v8 engine . Which is usually about a 5.2 liter engine.

How much torque does the engine in the 2006 Chevrolet Impala have?

The 2006 Chevrolet Impala's engine produces 214 ft-lbs. @ 4000 rpm.

Speaker size for 2001 impala?

Front Door's Speakers: 6-3/4"... Rear Deck's Speakers: 6" X 9".....

How do you remove the rear interior door panel on a 1992 Camry Specifically the inner door handle?

The door handle can not be removed till you have the panel off. Remove any screws first ... then slip a screwdriver around the bottom of the panel and start easing it out with a prying motion. follow all around the panel, then lift out vertically against the window. The handle is bolted to the inner door frame.

to completely remove the door without breaking the handle housing slip two smaller flat head screw drivers where at the top and bottom of the base of the handle, the housing clips in there, pry gently up on the top and down on the bottom one and pull the housing out from the back of the housing cause there is also a clip in the front that slides out