0
Dodge Durango
The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.
3,297 Questions
How do you change the clock settings on a 1991 Ford Focus?
2000 was the first model year for the Ford Focus.
Where is the plug for brake controller on 1998 durango?
Underneath the steering wheel, way back toward the firewall. It is light blue in color.
Will the engine out of jeep grand 4.7 with vin n fit in dodge durango 4.7 with vin n?
If the same year, it should.
If the same year, it should.
Check the hoses leading to the heater core from the engine compartment. I had a Nissan that had the same problem. The old owner had by-passed it because it had a leak. Yours could be the same if you are not the first owner.
Hope This Helps.
What is the size of the caliper bolts on a 1999 durango?
The front calipers on a 99 dodge Dakota are held on by 2 bolts that are removed from the back side of the caliper. You don't use a socket, you will need an Allen wrench. Not suyre of the size but probably 1/4 to 3/8 inch. timbob
AnswerIt's not an Allen wrench. Its a Torx or star point. The size is T45. AnswerIf it's not torx, then it's a 7MM Allen. Use a bit and ratchet to make removal easier. 3/8 drive bits are available at your local auto parts store. AnswerThey´re right, could be any of those, make sure you tighten them up very good when putting them back up, I lost one and "almost" had to get a full set of things which cost $40 for the calipers to be fitted, luckily I found a place where they saw my sample and sold me 2 more of a Grand Cherokee for $10. now I have a spare on my toolbox, hope never need itHaving just replaced the pads and rotors, I can confirm that the bolts are in fact T45. Get it on a 3/8" or 1/2" socket, the amount of torque and the position of the bolts would make a hand held driver very difficult.
How do you adjust the timing on 2000 dodge durango 5.9?
It is not really adjustable. The distributor "sync" (Chryslers' term) is set to 0 degrees with a scan tool.
It is not really adjustable. The distributor "sync" (Chryslers' term) is set to 0 degrees with a scan tool.
How to replace a brake light blub on a durango?
# Open the rear cargo door. # Use phillip's head screwdriver to remove 2 screws on side of light assembly. # swing light assembly out away from vehicle. # twist the bulb bracket counterclockwise 1/4 turn. # pull out. # remove bulb. # replace bulb(s). # reverse steps to reinstall light assembly.
Where is the egr valve located on 2005 Dodge Durango?
If you have a 4.7L it is on the drivers side right in back of the intake manifold.
When do you need to tuneup on Dodge Durango?
It depends on what engine and year it is.
Your friendly Dodge dealer will give you a list of recommended maintenance items including periods between.
Where is the starter in a Dodge Durango 2000?
Flywheel/trans area pass side/bottom. Follow the pos. batt cable to the end you will see a ft long object about 8" round-that's it.
What is the maximum cargo capacity of the 2007 Dodge Durango?
The maximum cargo capacity of the 2007 Dodge Durango is 102.4 cu.ft..
How many horsepower does the engine in the 2008 Dodge Durango have?
The 2008 Dodge Durango's engine produces 210 hp @ 5200 rpm.
Where is the crank sensor on 2003 durango 5.9?
In through the top of the bell housing. It is behind the trans dipstick tube, behind the passenger head.
How do you replace the spark plugs on a 2004 Dodge Durango hemi?
Overall, the job is not difficult. However, it is tedious, pricey, and it will challenge your toolbox a bit. A moderate amount of mechanical ability is all that's really needed.
Tools:
I recommend doing everything with 3/8" drives. My 1/2" spark plug socket wouldn't fit into the valve cover hole.
3/8" x 3" extension
3/8" x 6" extension
3/8" x 10" extension
3/8" x 24" extension
10mm gear wrench
3/8" swivel (do not even attempt this job without this!)
5/8" spark plug socket (for removing the plugs)
5/8" deep well socket (for installing the plugs)
extendable magnet (better to have it if you need it BEFORE you start)
You'll need 16 spark plugs. I used Champion platinums. On sale for $3.50 ea.
For wires, you get one box containing 8 wires.
Also, four boxes containing two springs and two plug "boots".
That's right, 16 plugs - 8 wires. Trust me. Total cost about $160.
1. Remove the intake ducting between the top of the air filter back to the hose clamp.
2. Remove the air box from the clamp to the throttle body. Two bolts.
3. For each, you need to remove the coil, which is held on by two 10mm bolts (they don't pull out but have a retainer clip in the coil. This is good!), and the two plugs.
4. I started with the forward most plug on the passenger side. There's a tube going right over the top, but you can get everything out. I promise.
5. For each plug, you'll need a new combination of extensions and swivel. It doesn't look possible, but you can actually get to all of them. PATIENCE!
6. I'd recommend removing all the coils from a side to open up more room to get to the back.
7. Remove each of the plugs with a spark plug socket attached to a 3" extension.
8. Gap the plugs to 0.045" (at least that's what my Champions were specified at)
9. To install the plugs, I dropped the plug in. Fitted the 3" extension to a 5/8" deep well socket and then inserted the socket and extension into the hole. I assembled swivel and extension on top each time depending on location.
10. Change the plugs on a side.
11. CAREFULLY change all the wires. You have to kind of lace them between the sides. It will make sense after you get all the intact plumbing off. I promise!
12. Reinstall the coils. The rubber boots just pull off. Fit the springs into the coil first, then slide the boot over them.
13. Repeat on the other side.
14. Start the engine and make sure it operates. This will probably set a Check Engine light. Mine cleared after a couple starts.
15. Reinstall the plumbing.
How do you replace the water pump on a 1990 Toyota Cressida?
There is no special procedure for replacing the water pump. You will have to remove the belts, fan at a minimum. To make the job easier it is recommended that you remove the radiator. It is also wise to service all consumable parts at that time with genuine Toyota parts: Hoses, coolant, thermostat & belts.
where are the camshaft position
How many quarts of oil does the 5.7 hemi take for a 2006 Dodge Durango?
7 quarts
Capacities:
Engine, with Wix 51085 Oil Filter.........7 quarts [1]
Cooling System, Initial Fill..........16.3 quarts
Automatic Transmission, 42RLE Initial Fill..........4 quarts
Automatic Transmission, 545RFE 2WD Initial Fill..........5.5 quarts
Automatic Transmission, 545RFE 4WD Initial Fill..........6.6 quarts
Automatic Transmission, Total Fill
5 speed 545RFE 4WD..........14.1 quarts
5 speed 545RFE 2WD..........14.1 quarts
4 speed 42RLE..........8.8 quarts
Wix 58846 Auto Tran Filter [1]
Wix 58843 Auto Tran Filter [2]
[1] 45RFE - Shallow Pan
[2] 45RFE - Deep Pan
Differential, C205F Front..........3.4 pints [2]
Differential, With 8.25 RingGear Rear..........4.2 pints [3]
Differential, With 9.25 RingGear Rear..........4.4 pints [4]
Transfer Case, NV144..........1.7 pints
Transfer Case, NV244..........3.4 pints
[1] After refill check oil level.
[2] Fill to level of fill plug.
[3] Fill no higher then 1/4 inch below plug hole.
[4] Fill no higher then 5/8 inch below plug hole.
TORQUES:
Oil Drain Plug.....25 ft/lbs
Transfer Case
Fill Plug 15-25 ft/lbs
Drain Plug 15-25 ft/lbs
NGK Plugs and Wiresets:
NGK - Ixiridium - NGK2313
Wireset - Direct Fire Ignition - [1]
[1] No Wires Req'd
Wiper Blades:
Driver | ExactFit - T261 | NeoForm - T16260 | Winter - T37260
Passenger | ExactFit - T211 | NeoForm - T16210 | Winter - T37210
Rear | ExactFit - T14C
How do you lower 1998 Dodge Durango 4wd?
lower? why i own a fancy 02 durango slt+ loaded with chrome up the yang yang and she's mint with patriot blue paint and silver trim and stands out anywhere i go and i would never lower mine im actually going get her lifted a bit. let me guess ur mexican? u always love the lowerd trucks stupid as hell.
Location of the Camshaft Sensor on 5.9 liter Magnum V8?
The Cam sensor is the "pick up plate" in the distributor, under the cap.
Where is the fuel cutoff switch on a 1998 DOHC Dodge Neon?
If you are referring to the inertia switch, look in your owners manual under "problems on the road". If no luck, you don;t have one. If you want to secure the fuel pump simply pull the fuse or relay labeled "fuel" Dodge doesn't use inertia switches.
What is the rear track of the 2005 Dodge Durango?
The rear track of the 2005 Dodge Durango is 5 ft. 4.4 in. (64.4 in.).
