0
Dodge Durango
The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.
3,297 Questions
How do you change the front drive axle in a 1998 Dodge Durango 4X4?
I have a 1999 dodge durango 4x4. oil was shooting out through a hose that came on the front axle I know that oil has
Is there a reset button for the fuel pump on a 1998 Dodge Durango?
Dodge does not use inertia/reset switches.
Is there a plug under the dash to wire a brake controler on a 2002 durango if so were?
It all depends on if your truck came with a factory installed tow package. If it did the hook up is in the area by the steering column. The way you can tell is look at your hitch and if it has a 7 blade outlet that has a cable that goes back into the chasis you should be good.
What should it cost to replace the rack and pinion on 2002 dodge durango?
Dealer quoted me $1,300, not including replacing the hoses. I decided to do it myself and it's going to cost less than $500 for parts (new complete rack, hoses, filter, fluid, outer tie rods) and having a shop do an alignment. The forums I've read say it's not too difficult and takes about 4 hours for a reasonably mechanically inclined person.
Where is the O2 sensor Bank 2 sensor 2 on a 2004 dodge durango?
That is passenger side after the catalyst.
How do you remove the fan clutch to replace the water pump on a 1996 dodge Dakota?
First, the neg. battery cable should be removed from the battery, the appropriate belts should be removed, the rad should be drained to at least as low as the bottom of the water pump's lowest point, and the top rad hose should be removed.
Then the fan shroud bolts should be removed.
The fan and clutch should be attached to the water pump hub by a large threaded nut.
If the fan clutch itself needs to be dissassembled, or if the water pump pulley bolts can't be accessed with the fan present, then wedge a prybar or long screwdriver between the pulley bolts to prevent the fan turning and, using the appropriate size wrench, turn the large nut counterclockwise to loosen and remove it.
If the water pump pulley bolts can be accessed then remove them and pull out the fan assembly and the fan shroud together.
Installation is the reverse of removal. Don't forget to put the shroud and fan back in together.
Is the 2006 Volkswagen Touareg front wheel drive rear wheel drive or four wheel drive?
The 2006 Volkswagen Touareg has all wheel drive.
What is the maximum cargo capacity of the 2012 Dodge Durango?
The maximum cargo capacity of the 2012 Dodge Durango is 84.5 cu.ft..
How do you remove front car seat in a 2001 dodge durango?
Should be secured by bolts in each corner of seat
What does a code P0441 EVAP emission mean on a 2003 dodge durango?
I have the same problem. I have found that if replacing the gas cap does not work you need a canister purge valve and/or canister purge solenoid. I know nothing about vehicles ..This is just what I have found out .
What commonly makes a 2004 dodge durango overheat?
on any car it is usually the thermostat. or low coolant level. if level is check radiator cap it may be loose or defective. but if it is dripping coolant from under engine it is your water pump. check under your car after about 10 minutes or so after you have parked if their is coolant or if you smell coolant under the hood after you park it most likely a water pump. Do not try to drive while it is over heated it will cost you a lot of money in damage.
How do you replace the water pump on a 1994 Nissan Sentra?
Not sure on a '94, but on a '90 w/ a 1.6 you just remove the pulley bolts on the water pump, take off the pulley and belt, remove the thermostat housing on the side of the water pump, and then remove the water pump bolts. After that you can take off the water pump.
What is the drive cycle for your 1996 Plymouth Voyager?
Check engine light off, codes cleared; cold start. -warm up engine 5 minutes (or until closed loop is reached--5 min is usually plenty) -drive (w/ steady throttle) at a steady speed between 40 and 60 mph for 8 min -stop and idle 3 min -drive (w/ steady throttle) at a speed above 20 mph for 2 min -turn key off, leave off 10 min
Where can you get a FREE wiring diagram for a 1999 dodge durango with the infinity sound system?
www.installdr.com (must have adobe)
How do you disarm the anti-theft system on your 1989 Cadillac coupe devile?
there is usually a button under the steering wheel under the panals that looks like a car lighter when you remove it if you pull the thing out maybe extend the wires and move it closer to the steering wheel you have to press that button and turn the key over at the exact same time and that should bypass the theft system i don't now if that's exactly the way it will work for you but i have a 92 elderado and that's what i had to do woth a try good luck
How do you replace the water pump on a 1991 Acura Integra?
Your best bet is go to the local parts store and buy the Haynes Manual. It is an easy process but involves meticulous attention to detail concerning the timing belt and since the water pump is diven from the timing belt, it has to be handled carefully. Keep in mind that you might as well replace the timing belt since your going to be in there anyways. MikeyRiceBurner
Where are ABS sensors located on a 1998 2500 Dodge Ram v10?
Both systems have one on the top of the rear axle. The four wheel ABS system also has one at each front wheel bearing.
How do you change ignition Lock Cylinder in 1990 Jeep Wrangler?
Use only Duncan Hines cake mix for this 2 eggs and 1/2 cup vegtable oil rub it on the cylinder start the engine that should work
How many quarts of oil does a 2002 Mercedes C240 have?
With oil filter replacement - about 6. Yes, in most quick lubes you need to pay for an extra quart.
Where is the camshaft sensor located on a 2001 Isuzu Rodeo 4 cylinder?
On a 2002 Rodeo it is located just behind the 2 cam gears which are right up front on top behind the plastic cover. I had to loosen the valve cover(12 small bolts on top) and pull the spark plug boots off for clearance to remove/replace it. All in all it's relatively easy.
