answersLogoWhite

0

Dodge Grand Caravan

The Dodge Grand Caravan is a long-wheelbase (LWB) model introduced in 1987 by Chrysler. This is the first generation of the family of minivan produced by the carmaker. It came in three trim levels: base, upscale LE and mainstream SE.

3,420 Questions

Where is the AC low side port on a 1998 Dodge Caravan?

Above and to the left of the high side charge port. It will be afixed to a flex line.

Right below the engine mount bar marked 2D. Look down right below the engine fluid cap.

-VG

How do you reset the auto shutoff relay on a 1996 dodge caravan?

The auto shutdown relay is controlled by the engine computer. You need to find out why it isn't actuating the relay. The first place to start is to check for codes.

--->>> A relay is good or faulty, you cannot reset it, just replace it. An 1996 caravan has NOT ASD relay at all!

How do you stop the indicator lights for AC and rear defrost and rear wiper from blinking on a 1998 Caravan?

Why do the middle console lights AC rear wiper flash after replacing the battery in '98 Chrysler Town Country How can these lights be reset?

This problem has bugged many of us T&C van owners. I have found several answers. I have tried them all to no avail. That doesnt mean that you can give it a go. This is one I tried that actually did make things better (two lights now instead of four flash).

a.. Set Blower motor ON HIGH b.. Set Mode position to Panel c.. Open all A/C outlets d.. Set Temperature to Cold (Both slide pots if equipped) e.. Depress WASH and REAR WIPER button simultaneously for 5 Seconds (Until all LED's light) RESULTS: a.. All LED's will turn on for 5 Seconds b.. Calibration Test is running when REAR WIPER and INTERMITTENT are alternately flashing. Cooldown test is running if A/C and RECIRC are alternately flashing. Wait till all lights stop flashing and only the aft wiper light is flashing. c.. Acceptable results is REAR WIPER LED is the only LED flashing. Push Rear Wiper to exit. d.. After all tests have passed, Calibration Diagnostics and Cooldown can be run separately. COOLDOWN TEST ENTRY a.. Set Blower motor ON HIGH b.. Set Mode position to Panel c.. Open all A/C outlets d.. Set Temperature to Cold (Both slide pots if equipped) e.. Depress WASH and A/C simultaneously for 5 Seconds NOTE: Prior to start of test, If the evaporator is already cold, the system will fail test. To correct, operate system with A/C OFF and the blower motor ON high for three minutes prior to starting test.

RESULTS: a.. All LED's will turn on for 5 Seconds b.. Cooldown Test is running when A/C and RECIRC. are alternately flashing. If A/C and RECIRC. are flashing simultaneously, Cooldown has failed. I you.. It did seem to help most folks. Its a shame that no Chrysler dealer in my area is even aware of this problem. If my machanic had known about this he could have dealt with it when he changed the battery. Good Luck!!

How can i install a new driver side window in a 1997 dodge grand caravan?

Remove the interior door trim panel. Remove the rubber trim that wipes the glass on the inside and outside. Move the window down until you see the bolts that hold the glass to the window regulator mechanism and remove the bolts. Remove any remaining glass. Spray the window channels with silicone spray. Tip the glass deep into the door and slide it into the channels. Then raise it up and fasten it to the regulator and install the bolts.

Rick

I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogspot.com

How to adjust a belt tensioner for a 1999 dodge grand caravan?

The belt tensioner is automatic and does not need manual adjustment. Put a 15mm socket on the tensioner nut and push downward a few times. The internal tensioning spring should put it back into the tight position on the belt again. If it does not, then the tensioner needs replacement.

What is the Dodge Grand Caravan cylinder numbering?

Standing at the radiator.

Front head left to right, 2-4-6 Rear head 1-3-5

I have a 1994 silverado pickup and the emergency brake is engaged and wont realeas how do i repair this or release it?

Answer EASY TO DOI would guess that it depends on what kind of car or truck you have, but on my 90 4 Runner it was easy. I have little to no knowledge about this before I started. My cable is made in 2 sections. I tracked the cable from the rear wheels to were they joined. About the middle of truck. Then on to the fire wall hole where it enters the cab. That was the hardest part. A simple clip holds the cable ends in place. Just pull the clip and that end of the cable will come loose. I also had a pully wheel that guides that cable to the brake handle that needed to be removed. It was held in by a cotter pin. Another clip on the other end (under the truck) of the cable released the cable as well as another cotter pin to pull out. Resecure all the clips as it runs the length of the truck (2 or 3 in my case) when you get the new cable ran and that about does it. Just a note about my brake handle. It is the kind that is on a bar that you pull toward your hip. When my cable broke the 12 inch bar came all the way out of dash. I had to remove lower dash and hold two little spring loaded teeth up while I reinserted the bar into the hole.THIS WAS TO EASY TO PAY SOMEONE TO DO!!!

Location of cabin filter in a 2003 Dodge Grand Caravan?

If your vehicle is equipped with one, it should be located on the passenger side, underside of the dash near the center console. It should be a black plastic snap-on cover about 1 1/2 inches wide by about 6 inches long, that may or may not be marked "cabin filter" (or something similar). Simply pop it off, pull out the filter (pay attention to its correct orientation, the airflow direction matters), install a new one, if necessary, and reinstall the cover.

You may need to use something to pry the filter out enough to grab, and you will likely need to bend the filter to remove and/or install it.

Which relay is the horn relay in the under-hood relay box on a 1991 Park Avenue?

On the 1996 model, there are two of them on the far passenger side of the underhood fuse /relay center.

What does this code mean for a 2000 pontic grand am P0131?

Trouble code P0131 means:O2 sensor circuit low voltage (Bank 1 Sensor 1)

Where is the interior fuse box in a 2001 Dodge Grand Caravan?

It doesn't have one. All fuses are under the hood.

It doesn't have one. All fuses are under the hood.

How wide is the 2011 Dodge Grand-Caravan?

The 2011 Dodge Grand-Caravan is 6 ft. 6.7 in. (78.7 in.)1 one-touch power windows wide.

How do you replace the rear wiper and washer on a 2005 dodge grand caravan?

I can't help you with the washer part of your question but I can help you with the wiper blade part:

The 2005 Dodge Grand Caravan has the most common hook-end wiper arms on front and rear. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

What is the towing capacity of a 79 Jeep CJ7 with a Class III Hitch?

Not much. It will depend on your engine, transmission, do you have a lift. The biggest problem is that the CJ is so light that it becomes a control issue. When I used to tow my boat (20' bow-rider) my front wheels would be so light that they would slid in a turn. I could pull it 60 mph but had to slow way way down before I came to a turn or corner and dirt roads were even worse.

Where is the crankshaft position sensor located on a 1996 Dodge Grand Caravan with 3.3 liter engine?

Just trying to help in my caravan its about 5 inches behind the crank pully but you might have to go under the van to locate it.

On a 3.3L it goes through the bell housing.

Why is your van sputtering while driving?

That could be any number of problems. Anything from bad fuel to an ignition system problem to a fuel system problem,etc. The list goes on.

How to remove and install a new starter?

(Also valid for 1998 model. //Scott C.) 09 April 2006 - Installed a new starter yesterday. Starter has 2 bolts holding it on the motor. Lift the hood and take off the air filter box blocking the view of the top bolt of the starter. After disconnecting the battery cables, take out the top bolt of the starter. From under the van, disconnect the cables to the starter. Take out the bottom bolt of the starter and it will back out from the motor. Don't let it fall on you! These new starters cost around $150.00 so, if you take it to a shop that rebuilds them, you can save a lot of money and most likely have a better starter than a "new" one. Most cars come with a "heavy duty" starter and parts stores usually don't give you that kind of a quality starter in return. //Master Sgt. Charles W. M.