0
Ford Windstar LX
Introduced in 1995, the Windstar LX was a first generation Windstar model powered by a 155 hp 3.8 L V6 engine, which can generate up to 220 lb ft of torque.
1,653 Questions
How much is it to fix your transmission?
i dont know what type of transmission you have but i had mine done in a 1999 dodge caravan with overdrive and it cost me 1200.00 dollars. that depends what is wrong with it but a ford pickup transmission will cost about 2000 dollars, dodge and chev are higher
The Ford Windstar sliding passenger door has adjustments on the roller guides. There are roller guides on the top and the bottom of the door. There are also adjustments on the stationary door latch.
How do you fix an Aveo that will not let you shift out of park?
I have an 04 Aveo and about 6 months ago my shifter would not get out of park unless you use the shift lock key. I found what the problem was by accident, but once I found the problem it makes total sense. Basically, one day I realized my brake lights were not going on, and after diagnosing the problem it appeared the brake switch was faulty. Once I replaced the brake switch, not only did it fix my brake light problem, but it also fixed my shifter problem. It's been about 5 months since the brake switch was replaced, and I never had the problem since. I think what was going on was since the brake switch was faulty, the car was not recognizing that you were pressing the brakes. Since you are not able to get the shifter out of park unless you are stepping on the brakes, it really makes total sense. But if I did not find this out by accident I don't know whether I would have been able to diagnosis it. I hope this is the problem you are having because it is a VERY cheap and easy fix - the switch is a $5 part and anyone can replace it.
After reading this, I was able to find and fix (although temporarily) the same problem with my daughter's 04 Aveo. Here is some more detail of the problem. First make sure that it is the brake switch by checking to see if the brake lights do not come on when the brake pedal is depressed. If the brake lights do come on, then the brake switch is OK - look elsewhere.
To remove the brake switch, slide the seat back and look above the curved bar to which the brake pedal is attached. The switch is black plastic with a white label with the letters WA in black. Disconnect the wires by firmly squeezing the white connector on the wide side and pull it off. To get the switch out of the metal bracket, rotate the switch 90 degrees and pull it out. To take the plastic switch case apart, pry apart at the parting line under the two triangles). Inside, there are two metal contacts. Push them out by pushing on the terminal blades from the end that the wires were connected. One of these two connectors is spring loaded on a flat spring and one is not. File the round disk connector pads (similar to ignition points). I found that the electrical resistance between the flat spring and its contactor disk was high, meaning that is was not properly closing the circuit - THE ROOT CAUSE!. So, I re-squeezed the riveted pad with a heavy duty pliers. The resistance (as measured with an ohmmeter) should go from infinity to 0 as the switch is activated. If this is the case, re-assemble, re-install, and then PURCHASE A NEW ONE. This is a dealer only part. Most auto parts stores can't get it for you. What we have done is a temporary fix.
What is the transmission fluid capacity of a Ford Windstar?
It all depends...
When you look at the Owners Manuals, you'll see transmission fluid capacity numbers in the range of 12-14 quarts.
BUT!
That's if the transmission is totally empty, and here's the clincher for us average types: including the torque converter.
For us average types, even when doing a transmission fluid / filter change, do not end up with an empty torque converter.
When you pull the transmission pan for the fluid/filter change, you end up with 4-6 quarts on average. The rest is still up inside the torque converter.
Measure what you drained and start with refilling that amount to put back in to return levels back to normal.
If you're adding fluid, simply use the dipstick - according to the illustrated instructions in the Owners Manual - and add what is necessary.
NOTE: This is one of the points of distinction to having the transmission "flushed" - where a professional shop is going to hookup specialized equipment to achieve a full fluid exchange.
Note #2: Many experts (like the guys on "The Car Show" radio program) assert that exchanging 50-60% of the fluids like would happen when doing a fluid/filter change is GOOD. The oil itself is not deteriorating so much as, what they call the "additive package" dissipates. So the percentage from doing the fluid/filter revives the "additive package" sufficient to support the long life of the transmission.
See "Related Questions" below for much much more - including links to your very own electronic copy of 1996 or newer Windstar Owners Manuals.
How do you replace the fuel filter on a Ford Windstar?
This YouTube video should be very helpful http://www.youtube.com/watch?v=31U3srwo74U&feature=youtube_gdata_player
Where is the abs relay on a Ford Windstar?
i had alot of problems with my abs brakes so i took out all the brake light bulbs and disconected the battery then i pulled the 30 amp fuse under the hood that is for the abs brakes . then i reconnected the battery but the emergency brake on and started the van put it in drive and let the computer reboot otself there by, bypassing the abs all together after 1/2 hr turn car off replace the brake light bulbs remember the top light to and now your abs will not give you any more problems. make shure to have your brakes changed regularly the windstars are bad on brakes. allso have your roters cut with every new set of brakes rear drums as well
bushmtn@yahoo.com
Where is the fuel pump reset button on ford wind star 2003?
On a 2003 Ford Windstar :
The fuel pump shut off switch ( inertia switch ) is located in the cargo area , on
the passenger side , behind a service panel cover
If the button has popped up on the top of the switch then no power is going
to the electric fuel pump and the switch has to be reset manually by pushing
the button DOWN
The power steering fluid is leaking in your 1992 ford thunderbird how would you fix it?
reroute the line around the power steering cooler
What causes a P1405 Error Code on a 1998 Ford Windstar?
P1405 Ford - DPFE Sensor Circuit Upstream HoseProbably caused by Faulty DPFE sensor (EGR pressure sensor), or a plugged EGR tube
What is the spark plug gap on a 1978 dodge 225 engine?
According to my Chilton's Auto Repair Manual :
The 225 slant six cylinder engine in a 1978 Dodge has spark plugs gapped at :
( .035 inch )
What transmission is in a 2002 ford Windstar?
I was looking at the 2002 Ford Windstar 0wners Manual ( and the Ford parts
website ) and they both show it as being the ( 4 F 50 N ) transaxle
( transmission )
Can you put valvoline 10W30 in a 2002 ford windstar?
I was looking at the 2002 Ford Windstar Owner Guide and it shows :
( 5W-20 is recommended )
How many cylinders does a 1999 ford windstar?
Both the 3.0 liter and 3.8 liter V6 engines offered in a 1999 Ford Windstar
have ( 6 engine cylinders )
Where is the blend door actuator 99 ford windstar?
The Blend Door actuator on the Ford Windstar can be found by removing the glovebox. A broken blend door actuator is almost as common as a broken blend door itself. Typically, the fix requires disassembling the entire dash and replacing the whole plenum box, which can be a costly repair. Linked here is a video from www.heatertreater.net demonstrating how to access components of the plenum box for repair without disassembling the entire dash. heatertreater.net/Windstar%20Video.html This details the best DIY option on how to replace a broken blend door or actuator.
What is the RPM for a 2001 ford windstar?
On your tachometer RPM stands for Revolutions Per Minute
( it indicates how fast the engine is turning )
How do you replace the thermostat in a ford windstar GL?
Before replacing the thermostat, be sure to check your blend door for functionality. The most common issue with heat or A/C in the late model Ford windstar is a broken blend door. A broken blend door actuator is almost as common as a broken blend door itself. Typically, the fix requires disassembling the entire dash and replacing the whole plenum box, which can be a costly repair. Linked here is a video from www.heatertreater.net demonstrating how to access components of the plenum box for repair without disassembling the entire dash.
Check engine light on steady = have your vehicle checked.
If it is blinking = have your vehicle checked now.
=============================================
Just adding to the answer :
If your check engine light is blinking that means that an engine cylinder
misfire has been detected . You can drive it in for repair , just avoid any
rapid acceleration or deceleration because you can damage the catalytic
converter
What does the symbol on the dashboard of a 2001 ford windstar that looks like an engine mean?
it is your check engine light. If it is on you are having problems with normal operation of the engine. Most of the time it is something very simple and emission related. Normally it is an exhaust gas regulation valve(egr) or an oxygen(o2) sensor. Go to auto zone and ask them to scan it for you to get the code that your power train control module(pcm) will have stored. They should do it for you for free. If you take it to a dealer they normally charge about 35 to 50 dollars to use their scan tool.
How do you stop the anti theft lights from blinking in a 2001 Ford Windstar?
Put the key in the ignition, start the van and press the remote starter button on the remote. Problem solved. This helped us after we had this problem after recharging our dead van battery.
Why did bigger cars have to have bigger steering wheels before power steering?
in my opinion, im pretty sure a bigger car has to have a bigger steering wheel because a tiny steering wheel would not be able to manuver a big car. great question though:)
hope i helped:) love, izzy
Answer 2Some of it has to do with the scale and dynamics of the vehicle, but it's mostly that a larger steering wheel has more leverage. It takes less effort to turn a larger steering wheel than a smaller one.To turn a 15 inch diameter steering wheel half way around, it requires you to turn it about 24 inches. If that wheel was 25 inches in diameter, you'd have to turn it almost 40 inches. It's a bigger lever; you have to turn it more (further), but it is easier to turn.
Many older cars without power steering also had more 'turns' to the wheel, which gives the same advantage. My Honda maybe has three turns to the wheel - 'lock to lock' (from all the way left to all the way right). One of the earliest cars I drove may have had 10 turns to the wheel. I remember having to turn it about half way around just to change lanes.
What does it mean when your car just keep whirling over?
Starter solenoid is bad. I assume you mean engine turning over, not starting, but continuing to turn over after key is released. Disconnect battery cable from post, then replace starter solenoid.
To realign the sliding door on your 2003 Ford Windstar, start by examining the hinge and roller assembly for any visible damage or wear. Loosen the hinge bolts and adjust the door's position until it sits flush with the trim, then retighten the bolts. Additionally, check the roller assembly for proper alignment and ensure it moves smoothly along the track. Finally, test the door to ensure it opens and closes properly after adjustments.
