0
Honda Accord EX
Introduced in 1984 with a 1.8 liter engine, Honda Accord EX was marketed in New Zealand, Australia, Canada, and the US. The EX replaced the LX-I and SE-I models during the 1990s.
5,157 Questions
Does a 2003 325i auto have a cam belt or a cam chain?
The 2.5 liter - 6 cylinder engine - in a 2003 BMW 325i has a timing CHAIN
Where is the neutral switch on 1999 Honda Accord ex automatic?
It's right under the plastic casing where the gear stick is. What you do is use a screw driver to pop the casing off temporarily. Beside the gearstick there is a slot for your car key (top left). When you insert the key the gear can then be shifted. When you're done you can replace the plastic casing around the gear stick.
Does a 1988 Honda Accord have struts or shocks?
Both shocks on the front, struts on the back depending on the make it might have it both ways!
When should you change your struts on your 1999 Honda accord?
They should be good for at least 100,000 miles. Have them inspected at that time unless you suspect they may need inspecting earlier.
What can red maintenance required signal mean in 1991 Honda accord?
IT'S TIME TO CHANGE OIL. THIER SHOULD A SMALL BUTTON TO PUSH IN TO RESET.
Remove fuel pump 1999 Oldsmobile silhouette?
Remove all the gas in the tank. Put the vehicle on a lift. Support the tank and remove two straps. Remove the filler hose from the tank. Slowly drop the tank until you can access the top. Remove the plastic lock on the wiring harness. Remove the wiring harness. Remove the pump outlet line and the gas return line. Mark them so you won't get confused. Drop the tank to the floor. Remove the lock ring lock. Using a spanner or 6 inch channel-lock pliers, rotate the lock ring counter-clockwise. Impart a downward pressure as the fuel pump is spring loaded. Pull up on the pump and remove. Replace with new gaskets and lock ring lock.
Does the Honda CR-V 1996 have a automatic door lock switch?
The lock on the top of the drivers door acts as the power lock switch for the crv, open (up) and close (down) while in the car. To lock all doors from outside the car hold open inside door handle and push down lock on top of door. All doors should lock. Close door.
VTEC stands for Variable Valve Timing and Lift Control. It is a valve timing system developed by Honda to improve both performance and economy in their four cylinder engines. At low RPM the engine is more fuel efficient and at high RPM the engine produces more horsepower.
2008 Honda Accord lug nut toque specs?
80 ft/lbs of torque. Tighten in a criss cross pattern. Do not over-tighten or you will warp the rotors.
How do you replace the thermostat located on a 1992 Honda Accord?
follow lower hose to rear of engine. rember to bleed. bleeder located on the upper radiator hose housing.
How do you change cabin air filter on 2008 Honda accord?
It is the same as the 8th generation Civic...which can be viewed here: http://uk.youtube.com/watch?v=UNFRM87JZQk
How do you replace the TCM on a 1998 Honda Accord?
I would recommend going to your local mechanic for this. Replacing a TCM requires a lot of knowledge. It would be best for your safety and other's to go to a professional.
How do you replace the front wheel bearings on a 1990 Honda Accord?
The large nut will not come off, any suggestions?
I used a bent jack handle...put it in between the lug nut bolts until it hit the ground and wasnt turning anymore, got a 1/2'' rachet about a foot long and a socket to fit and stood and jumped on it til it come off...i have a 93 im trying to replace the wheel bearing on passenger side and it's a bi+c4 to get to anything, you have to beat the axle back into the car and take off the 12-side headed bolts (4 of them)...which im doing it the red-neck way cuz im too cheap to go get it done...so i went and bought the part myself and did it myself...going to do it now as a matter of face...later good luck
I bought a 1/2" drive socket (I think it's 34 mm) at AutoZone for around $18, and I bought a 24" 1/2" drive ratcheting breaker-bar at Harbor Freight Tools for around $15. Also bought a "pickle fork" ball joint separator for around $10.
Remove wheel cap, use breaker bar and socket to loosen the big nut BEFORE JACKING THE CAR. Then jack the car, remove the wheel. Remove the large nut the rest of the way. Remove the brake caliper, do not disconnect the brake line, tie the caliper from the upper control arm with a piece of heavy wire. Remove cotter pin and lower ball joint castle nut. Remove the bolt from the lower control arm that connects the bottom of the strut to the lower control arm, (called a damper fork) You don't need a spring compressor, you are Not decompressing or removing the strut/coil spring. Use the pickle fork and a BFH to separate the ball joint/lower control arm from the bottom of the spindle. Pull spindle toward you to separate it from the splined drive axle. There are four bolts that hold the hub assembly to the spindle, (14mm, I think). Soak them with WD-40, they may not come easy.
On this vintage Accord, the assembly comes out from the front of the spindle, the hub assembly is a unit that bolts in, and is NOT pressed out by a machine shop. They rust in place and are sometimes extremely difficult to get loose from the spindle, even with all four bolts out. Heat it up with a torch if that's available to you. I've done it a couple other times where the hub comes right out easily. One other option is to separate the spindle from the upper ball joint, (again, leaving the strut in place) and work on the whole thing on the bench if possible. Don't forget to unplug the ABS wire (if you have ABS) from the engine compartment and thread it through the hole, I don't recommend trying to disconnect that at the spindle.
The bearing hub costs less than $25 each on eBay, and they interchange all the way from 1990-1997 if you're the junkyarding type.
Good luck and have fun.
What cars bolt pattern is 5x100 17?
Potential Matches
5x4.00 / 5x100
2000-2006 Audi TT (4 cyl.)
2000-2006 Audi TT (4 cyl.) Quattro
2000-2006 Audi TT (V6)
1980-1998 Buick Skylark
1989-1996 Chevrolet Beretta
1982-2005 Chevrolet Cavalier
1989-1996 Chevrolet Corsica
1995-2001 Chrysler Cirrus
1988-1993 Chrysler Fifth Avenue (FWD)
1988-1993 Chrysler New Yorker
2001-2010 Chrysler PT Cruiser
1996-2006 Chrysler Sebring Convertible
2001-2006 Chrysler Sebring Sedan
1986-2000 Dodge Caravan
1990-1995 Dodge Caravan (AWD)
1984-1993 Dodge Daytona
1988-1993 Dodge Dynasty
1996-2000 Dodge Grand Caravan
1994-2006 Dodge Neon
2003-2006 Dodge Neon SRT 4
1980-1994 Dodge Omni GLH
1980-1994 Dodge Shadow
1980-1994 Dodge Spirit
1995-2007 Dodge Stratus Sedan
2001-2007 Dodge Stratus R/T Sedan
1990-1991 Lexus ES 250
1992-1997 Oldsmobile Achieva
1992-1997 Oldsmobile Achieva S
1992-1997 Oldsmobile Achieva SC
1992-1997 Oldsmobile Achieva SL
1982-1991 Oldsmobile Calais
1982-1991 Oldsmobile Ciera
1982-1991 Oldsmobile Cutlass
1982-1988 Oldsmobile Firenza
1980-1985 Oldsmobile Omega
1984-1988 Pontiac Fiero
1984-1988 Pontiac Fiero GT
1986-1998 Pontiac Grand Am
1985-1994 Pontiac Sunbird
1995-2005 Pontiac Sunfire
2003-2008 Pontiac Vibe
2009 Pontiac Vibe 1.8
2005-2006 Saab 9-2X
2005-2010 Scion TC
2008-2011 Scion XD
2008-2009 Scion XD TRD
1997-2011 Subaru Forester
1993-2009 Subaru Impreza
2002-2009 Subaru Impreza WRX
2003-2004 Subaru Impreza STI
2010-2011 Subaru Impreza 2.5
2010 Subaru Impreza WRX
1990-2011 Subaru Legacy
2000-2009 Subaru Legacy GT
1995-2007 Subaru Outback Wagon
2005-2011 Subaru Outback
1986-1991 Toyota Camry
1986-2005 Toyota Celica GT
1990-1993 Toyota Celica All-Trac
1990-2005 Toyota Celica GTS
1992-1999 Toyota Celica ST
2003-2010 Toyota Corolla
2002-2009 Toyota Matrix
2009 Toyota Matrix S
2010 Toyota Matrix Base
2004-2011 Toyota Prius
2006-2009 Toyota Prius Touring
1998-2010 Volkswagen Beetle
1998-2009 Volkswagen Beetle turbo
1993 Volkswagen Corrado SLC (V6)
1993-1998 Volkswagen Golf III GTI
1993-1998 Volkswagen Golf III VR6
1993-1998 Volkswagen Golf VR6
1999-2005 Volkswagen Golf IV
1999-2005 Volkswagen Golf TDI
2004 Volkswagen Golf R32
1999-2005 Volkswagen GTI 1.8T
1999-2005 Volkswagen GTI VR6
1993-1998 Volkswagen Jetta III GLX
1995-1998 Volkswagen Jetta III VR6
1999-2005 Volkswagen Jetta IV (4 cyl.)
1999-2005 Volkswagen Jetta IV VR6
1992-1997 Volkswagen Passat VR6
Why did the trunk motor on a 1991 Park Avenue suddenly stop working and now the trunk won't latch?
I have a 1992 Buick Park Ave. My trunk did the same thing. You need to go to the GM dealer and order or buy a trunk motor switch. They are only $18.00 and will take you only 30 minutes or less to install. The switch is a little black colored rectangular box shaped thing, with 2 long screws bolting it up next to your trunk closer motor. Without the above, you won't be able to close the trunk unless you "jerry rig" the trunk latch. Save yourself lots of aggrivation...do it the right way! Doc..
What is the fastest motor you can fit in a 91 Honda accord?
The 91 Accord engine bay will fit a Prelude H22A or H23A motor without too much modification. You should even be able to use the same wiring harness on earlier donor car motors. If the donor motor is from a pre 1995 it should basically bolt in. The 91 Accord engine bay will fit a Prelude H22A or H23A motor without too much modification. You should even be able to use the same wiring harness on earlier donor car motors. If the donor motor is from a pre 1995 it should basically bolt in.
Where is the brake light failure sensor located on a 1991 accord?
In the rear tail light assembly one for each side.
Where can you get the screw for the 2008 Honda accord keyless enter remote?
I would try a clock repair shop.
Where is the torque converter on a 2006 Honda accord?
Mounted between the engine and the transmission.
some thing is probley cloging the vents take it appart and ckeck.
Can anyone supply me with a Wiring diagram for a Ryder Split charge relay unit?
Hi,
Full instructions and very comprensive information can be found on the manufacturers web site www.rydertowing.co.uk
I am sure this will answer all your questions.
Dave
2002 Mercedes Benz S430 the car is raise up and now it would not lower down?
I had same issue, I had to replace a computer module and the buttons on the dash for it to be fixed. I am sure only one was the issue, but you know how Mercedes is once they install it and it doesn't fix it they don't want to take it back out. They also tried to replace the air shock seals, but they had just been replaced so they weren't able to charge me again for those. Good Luck
