Isuzu

Wiper motor is not working properly or the combination switch in the steering column is not working properly which is the lever that turns the wipers on.

6-8 kilometer/ltr

The location of the coolant temperature on the 1996 Honda Passport is actually behind the alternator. You can see the sensor in any Haynes or Chilton's manual for that vehicle year.

16

Mr Shinzo Nakanishi is Managing Director and CEO of Maruti Suzuki

Most recent inquirey is 20.5 L.......maybe.

They hold 13.3qts filter dry......100% correct!! No maybes from this tech.

What engine ??

4he1 10lt

4hf1t / 4hf1t 13.5lt

98 Isuzu npr oil capacity

Well I could go into a long drawn out discription on how to do the hpp on an 4hk. Here's a quick overview. set enging to tdc #1 cyl conpression stroke. remove fuel lines and pump.

Head stud tension on Isuzu G200

Phase 1. 29ft/lbs or 39 newton meter

Phase 2. 54ft/lbs or 73 newton meter

Phase 3. 72ft/lbs or 98 newton meter

injection pump crankshaft camp

1342 (typical)

1991-1996 Isuzu Rodeo's use THM4L30-E Automatic Transmission. It also bolts directly to the transfer case and is claimed as one unit, and is recommended to be removed as one unit, then separated from each other outside of the vehicle. Hope that helps you. That is what my service manual said. Nothing quoted or directly reworded.

My TOD light is flashing. My brother's TOD light has been flashing for over a year. There are only three components that are possible to fail in this system. 1) the TOD computer 2) the viscous coupler (clutch) inside the transfer case 3) the speed sensors on transfer case.

The clutch in the transfer case almost never goes bad, and would be a lot more major to fix, so start with the easy stuff. My brother replaced his computer with a known working computer, still didn't fix the problem. He then bought new (used) speed sensors and installed them. Problem didn't go away. He then checked every single electrical connection in the system, didn't fix it. Installed another known working set of speed sensors (there are two), and that fixed the problem. It seems like this is the most common reason for failure of the TOD system. I haven't located new speed sensors for mine, but I'm fairly certain that is the problem. You can verify by pulling the codes using a code reader, or a simple test light (the code reader is a much easier way and most auto parts stores will run the codes for you).

Good luck.

Cleaning will not help. The piston is going cocked in the bore. Rebuild or replace.

This displaces the fuel vapor as it's purged into the combustion process. Code P0446 indicates that there is an improper voltage drop in the EVAP Vent Valve circuit, which can be caused by either too little or too much electrical resistance. This improper electrical condition will cause the vent valve to malfunction.

go to myisuzuparts.com, once there if you type in a part that your looking for it will have a little camera symbol to the far right and if you click on it it will show a pretty good diagram, you can type in 3.5 L eng and get a decent diagram,

The glow plug relay is on the drivers side of the truck in a relay box on the chassis frame behind the drivers side tire.

which module is it?

how do i install a radiator on a 1993 isuzu npr?

1 8 7 6 5 4 3 10 9 2

1. Move the driver's seat forward, and locate the security system control unit mounted on the underneath the seat.

2. Turn on ignition switch on.

3. Press and hold the green programming button on the control unit with a pen. you will have to poke through a hole about the size of a pencil located on the side of the unit. when the security system LED on the instrument panel comes on, release the program button, (Step 3 and 4 must be done within 5 seconds of each other.)

4. Press and release the top button on the transmitter, check that the LED goes out chirps once, and the front marker lights flash to confirm that the transmitter's code worked by the control unit.

5. if you have other transmitters to program, repeat steps 3 and 4.

6. Turn the ignition switch off to exit the programming mode.

Dextron 3

10.5 qts

Not sure about the sub model, but a 3LB1-EAO4 is 0.02 millimeters. Good luck!

6