0
Mazda Protege
Also known as Familia in some markets, the Protégé was a compact car produced by Mazda Motor Corporation from 1964-2003 for the North American market. The Protégé was one of the company’s best sellers and was manufactured in eight generation models.
1,312 Questions
You have a 1992 Mazda Protege hold light remains on?
I suspect your hold switch on the shift lever might be bad..or ahs a broken wire.
Where is map sensor located on 1998 Mazda protege?
Under the hood on the firewall passenger side it will say hitachi boost sensor on the top of it
How much is it to replace a 99 Mazda protege serpentine belt?
The cost to replace a 1999 Mazda Protege serpentine belt will vary depending on the cost of parts and cost of labor. The prices for the serpentine belt start at $14.56.
What are the speaker specs for a 1994 Mazda Protege?
6.5 inches. No screw patters match the protege, you'll have to drill alittle bit.
How do you check non-interference interference engines Mazda Protege 5?
According to Gates Rubber and Preferred Components, two timing belt manufacturers, Mazda has several engines that are "interference-type" engines. On some Proteges, the 1.6 and 1.8 are safe, but the 2.0 (1991cc DOHC) most definitely will cause major damage if the timing belt breaks. Mazda recommends T-belt replacement every 60,000 miles on most of their engines, interference or not. The two belt manufacturers I mentioned above have details on engine specifications from all auto makers available on their websites.
How can i fix my 94 Mazda protege got flooded and cranks but won't start?
Flooded in the river or flooded by gas? Any "check engine lights"? Full gas pedal depression is the normal way to clear gas flooding or first remove the spark plugs and blow out the excess gas.
Does a Mazda Protege 5 have a voltage regulator?
yes it does it is mounted in the rear of the motor. ////// i would think it would be like other cars integrated in the alternator
Where is the fuel pump located on the 1995 Mazda Protege with a 1.5 engine?
The fuel pump is located under the back seat. Pull up on the front of the back seat and you will see a cover plate with four screws. There is also a wire going through the middle of th plate.
How do you change an alternator belt on a 1998 Mazda Protege?
Go to your local library and look at the Chiltons automotive book for your year car. It can help you tremendously. I do know you need a tension bar and two people to do this. Be careful as the belt is under alot of pressure and can snap in your face.
Take it to a place that does free check engine light check. Some will reset it after they check it for you. Place in New York State are listed on http://NewYorkForum.us
Where can you find the wiring diagram for a 2000 Mazda Protege?
A quick chart is available in pdf format for Mazda cars 1992-newer at www.installdr.com/Harnesses/Mazda-Wiring.pdf
hey all i know is that BLK = GROUND
BLU/RED = BATT
PINK/BLK = IGN ACC
GRN/BLK = PANEL LITE CTRL
YEL = DIMMING
BLK/RED = DOOR LH +
BLK/WHT = DOOR LH -
RED = DOOR RH +
WHT = DOOR RH -
BRN = REAR LH -
BRN/WHT = REAR LH +
GRN = REAR RH -
GRN/YEL = RER RH +
What type of oil does a 2000 Mazda Protege use?
the same type of oil as any car i believe ask your dealer they will know
To purge a gas line go to the gas line at the appliance. Turn the gas cook(cut off) to the off position(perpendicular to the gas line). loosen the gas line on appliance side of gas cook (this is done at a flare fitting or union). Next turn the gas cook back on until you smell gas.Turn gas back off and re-tighten gas line. Turn gas back on and check for leaks(50/50 water and dish soap sprayed onto fittings). No bubbles means no leaks.
Where are the spark plugs on a 2002 Mazda Protege?
The spark plugs are located at the top of the engine block. Two have Plug Wires going to them the the other two have the coil already attached to it. These can be remove with a 10mm socket. Gently pull up on the plug wires as to not break the connection from the wire to the Plug Wire socket. Hope this helps.
What have you done so far? Have you checked the brake fluid level?
How do you replace the headlight bulb located on a 1999 Mazda Protege?
Then you have to pull back the round rubber boot from the back of the head light assembly. Remove the boot and lay it aside. (Or, if you cannot pull out the connector, just bend it back.)
[For easier access to the assembly, pull the coolant container straight up. It will come off the flat peg it sits on.]
After that, you can flip the metal tab wire that is bent in the shape of a small paper clip off the bulb. Go the the starboard (right while facing forward) end of the wire. You can push down the end of the wire, and disengage it from the tab that end sits begin. Then you can flip the entire wire off the bulb. While the tab is pushed down it also must pop toward the rear of the car to clear the plastic notch that it is hooked into. I used a small screw driver. This same wire extends around to the opposite side of the bulb where it is hinged. This wire holds the bulb in its mount.
The bulb will come out easily now. (If you still need to, pry the three bulb prongs (look at the new bulb to visualize this) out of the power connector. Now you can remove the rubber boot.) Note the way it comes out and put new bulb back in the same way. There are 3 square tabs on the bulb that need to go into the 3 matching notches inside of the headlight assembly. They keeps the bulb in the correct position. Inserting and positioning the new bulb does not require any force. Re-connect the wire tab mount that secures the bulb. Remember... fingers off the glass part of the bulb.
Then put the rubber boot over the end of the bulb, and over the hole so it acts as a gasket. Then put the three prongs into the power connector, and you should be all set!
Where is the oil dipstick for a Mazda protege?
This applies to a 2003 Mazda Protege: It depends on what type of engine you have.
For the 1.6L engine, the oil dipstick is the front-passenger side area, close to the power steering reservoir.
For the 2.0L engine, the dipstick is on the same side but towards the back, close to the wheel.
Mazda protege it has water in the spark plug slots?
You have either a blown head gasket or a cracked head
How do you replace the alternator belt on a Mazda Protege 1995?
you have to loosen the top alternator bolt alowing the alternator to swing forward loosening the belt
Trouble code P0170 means: Adaptive Fuel Trim Too Rich or Too Lean (Bank 1)
Either the battery just shows charged under no load or a bad ground at the terminals or starter. I think?
How do you replace the horn on a 2000 Mazda Protege and where is it?
I could not find it either :)
Its under the front grill :-) just remove the grill (two screw on top as I remember and then you have to just pull it off) and rest is VERY VERY simple :-)
